Home Blog  
Education / Training Airgun seals: Where are they?

Airgun seals: Where are they?

by B.B. Pelletier

A new reader named Carl prompted today’s post. He owns a Daisy 22X and has some questions about oiling the seals. That resulted in this question:

You mention that you should keep your seals oiled. Where are these seals located?

I’ll do multi-pump pneumatics today and if there is interest, I’ll do the other types of airgun powerplants later.

Starting with the pump head
Think of a multi-pump gun as a progression of events. First, you pump air into the gun’s reservoir. That takes a pump head that can seal air against loss as it compresses it into a small space. The pump head is a pliable material that fits the inside of the pump tube tightly enough to compress air but loosely enough to move easily. The pump head usually swells from increasing air pressure. In some guns, there’s an O-ring, like a piston ring, around the head very near the end. Oil on the contacting surfaces of either the O-ring or end of the pump head seals the air in front of the head, just as oil in your car engine helps the piston rings seal the explosive gasses of combustion.

multi-pump-seals-web
This rough diagram shows the relative locations of the seals in a multi-pump.

The inlet valve
As the pump head compresses air, the inlet valve in the end of the reservoir is forced open by air pressure. Air passes into the reservoir, which in most multi-pumps is nothing more than empty space inside the valve body. It doesn’t take much air to drive a pellet! When the pump stroke is complete, the inlet valve’s return spring closes the valve. As the reservoir pressure increases, more pressure is needed to open the inlet valve, so the pump head travels farther before the inlet valve opens. You feel the increased pressure as feedback in the pump stroke.

The exhaust valve
Air remains in the reservoir/valve until released through the exhaust valve. Typically, a spring-driven weight called a hammer knocks the exhaust valve off its seat, releasing the air. The released air flows through the same tunnel the valve stem operates in, but a hole in the side of this tunnel lets the air escape up to the barrel, where it gets behind the pellet. The bolt that loaded the pellet has an O-ring seal on it, so the only way the air can escape is to push the pellet out of the way.

Pump tube to barrel seal
This just keeps the air sealed inside the tunnel so it has to push the pellet out of the way.

Oiling all the seals
When you oil the pump head, oil migrates through the gun with the compressed air. By oiling this one spot, you are oiling the entire airgun.

author avatar
Tom Gaylord (B.B. Pelletier)
Tom Gaylord, also known as B.B. Pelletier, provides expert insights to airgunners all over the world on behalf of Pyramyd AIR. He has earned the title The Godfather of Airguns™ for his contributions to the industry, spending many years with AirForce Airguns and starting magazines dedicated to the sport such as Airgun Illustrated.

28 thoughts on “Airgun seals: Where are they?”

  1. Denny,

    Resealing a CO2 gun isn’t hard if you have the parts, but getting them is very hard.

    Most repair stations make some of the parts they use. Sometimes a manufacturer like Crosman will help with current models, but nobody helps with older guns.

    B.B.

  2. I have a Daisy 990 and was told it had 14 seals.

    I was told this gun was worth some money but have not been able to find anyone to buy it. Can you tell me anything about the 990 is it worth keeping or should I sell them? Where can I sell them?

    thanks

  3. Ya I would like to boost the guns velocity(although it is already a magnum break barrel)even though it is well powerfull enough for hunting,it is nice to upgrade velocity on a nice gun like this.

  4. Jed,

    If Jim Maccari will work on a Legacy I suppose he could do something for you. It might run $100 to 150, or so.

    You might try John Groenewold for a replacement mainspring or a tighter piston seal, and I guess you could shim the inside of the piston with stainless steel shim stock.

    Increasing the preload of the spring with spacers might also help. And a tighter spring guide will smooth out the action.

    B.B.

  5. Hey Jed,

    Congrats on your new purchase!! Would sure appreciate an update on the accuracy of the .22 Legacy once you get her dialed in. How do you think the accuracy compares with BB’s experience with the .177?

    Any other observations, hold techniques, scope mounting recommendations, etc, are also welcome!

    Are you thinking about the Bug Buster 6x? I am giving this scope some consideration. PyramydAir’s recommended mounts are either B-Square on a base or Reapers non-adjustable 2-piece mounts. I think I might prefer 2-piece adjustable mounts personally, but they may not be necessary or justify the expense. Thoughts?

    I’m also assuming that a stop pin will be a must with this springer….

    Anyone care to share their experience/opinion on mounts for the .22 Legacy/Bug Buster?

    Many thanks,
    Will

  6. Speaking of oiling, what is the proper way to oil the combustion chamber of a springer?

    I know not to over oil and to use ony a drop of proper oil. However, when I have waited until the cocking stroke squeaks, put a drop of oil down the transfer port, left the gun upright for a night, and then repeatedly partially cocked before firing — I get a dieseling shot. I don’t like even one shot that diesels. What am I doing wrong?

  7. You aren’t doing anything wrong, but here is a tip. If your gun allows de-cocking, try cocking and uncocking the gun several times after is has been upright all night. This spreads the oil around the piston walls of the compression chamber.

    I like to hold the gun horizontally in four 90 degree rotations around the axis of the barrel. That helps spread the oil everywhere.

    I have found this trick will cut down on first-shot dieseling.

    B.B.

  8. Well I tried the Legacy firing at 20 yds,accuracy is very good.I hadn’t ajusted sights yet and shot without a scope or much concentration but I got good accuracy half 0.50 to 1.00 inch group.

  9. B.B I would like to ask a question.Did your Legacy puff out smoke and give good kickback when you shot it?Because mine did,I never shot a .22 firearm with this much kickback,though what I am wondering most is the smoke cloud puff after shooting it,this gun really makes you forget your shooting an airgun,that is what I like about it.

  10. You wrote: “I’ll do multi-pump pneumatics today and if there is interest, I’ll do the other types of airgun powerplants later.”
    please do, I would greatly appreciate it! Thank you.

  11. Jed,

    The smoke is from dieseling. Yes, mine did it, too. Most new spring guns diesel.

    The recoil is from the spring and it doesn’t go away. Don’t hold the rifle tightly when you shoot. Let it recoil as much as ity can for best accuracy.

    B.B.

  12. Totally off topic;

    I am trying to replace the stock on my Gamo CF-X and so far have not found an exploded view of it, so am forced to guess. Anybody know how the front is attatched to the barreled action/chamber/cocking mechanism?

    Or maybe where I can find an exploded view if CF-X?

    dsw

  13. Ya didn’t have a problem with the recoil in fact I like that it has more recoil.Good to know thats all that was causing the smoke.I definately paid little for a rife this nice.I like the .22 version real good.

  14. I shot Beeman eatra heavy Kodiac pellets(22 grain) in the Legacy .22,the gun definately has the power to use them,they did just fine with accuracy and power.

  15. That is stupid of them.If I buy an airgun that is medium or high end and it’s available in .22.I certainly will buy it in .22 not seventeen caliber!I don’t like that caliber .177 is too small,once you get larger calibers you never want a .177 rifle again.At least thats how it is for me.

  16. Gamo and .22,

    I covered this some time back. Gamo sells by the truckload to Wal Mart and the other big box stores. They are not interested in adult airgunning unless there are thousands of adults clamoring for something. In this case, there aren’t.

    This is a numbers game for them, and .177 is winning the race. One reason for that is the American communities that have demonized .22 caliber by making it illegal. So Wal Mart won’t buy them and Gamo isn’t interested in selling to anyone else.

    B.B.

  17. I am going to dust off my late 80s/early 90s RWS Model 34. I haven’t shot it in over a decade. I am going to clean and oil it. I have the RWS shooters cleaning kit. I am not sure if I should both oil the main spring and the chamber. On the RWS site it says you can use a drop or two in the chamber or ALTERNATIVELY just oil the mainspring. So, what would you recommend? Also, to do the chamber…where would I want to use the needle/oil…where is the ‘compression chamber port?

    Thanks!

  18. BB,

    Thanks a lot for your post. I was thinking that to oil the seals of my Daisy 22X, that I’d have to take the gun apart. It’s nice to know that oiling the one spot will do the trick for the whole gun:)

    Thanks again,

    Carl

Leave a Reply to Will Cancel reply

Buy With Confidence

  • Free Shipping

    Get FREE shipping on qualifying orders! Any order $150+ with a shipping address in the contiguous US will receive the option for free ground shipping on items sold & shipped by Pyramyd AIR during checkout. Certain restrictions apply.

    Free shipping may not be combined with a coupon unless stated otherwise.

    View Shipping Info

  • Shipping Time Frame

    We work hard to get all orders placed by 12 pm EST out the door within 24 hours on weekdays because we know how excited you are to receive your order. Weekends and holiday shipping times will vary.

    During busy holidays, we step our efforts to ship all orders as fast as possible, but you may experience an additional 1-2 day delay before your order ships. This may also happen if you change your order during processing.

    View Shipping Times

  • Shipping Restrictions

    It's important to know that due to state and local laws, there are certain restrictions for various products. It's up to you to research and comply with the laws in your state, county, and city. If you live in a state or city where air guns are treated as firearms you may be able to take advantage of our FFL special program.

    U.S. federal law requires that all airsoft guns are sold with a 1/4-inch blaze orange muzzle or an orange flash hider to avoid the guns being mistaken for firearms.

    View Shipping Restrictions

  • Expert Service and Repair

    Get the most out of your equipment when you work with the expert technicians at Pyramyd AIR. With over 25 years of combined experience, we offer a range of comprehensive in-house services tailored to kickstart your next adventure.

    If you're picking up a new air gun, our team can test and tune the equipment before it leaves the warehouse. We can even set up an optic or other equipment so you can get out shooting without the hassle. For bowhunters, our certified master bow technicians provide services such as assembly, optics zeroing, and full equipment setup, which can maximize the potential of your purchase.

    By leveraging our expertise and precision, we ensure that your equipment is finely tuned to meet your specific needs and get you ready for your outdoor pursuits. So look out for our services when shopping for something new, and let our experts help you get the most from your outdoor adventures.

    View Service Info

  • Warranty Info

    Shop and purchase with confidence knowing that all of our air guns (except airsoft) are protected by a minimum 1-year manufacturer's warranty from the date of purchase unless otherwise noted on the product page.

    A warranty is provided by each manufacturer to ensure that your product is free of defect in both materials and workmanship.

    View Warranty Details

  • Exchanges / Refunds

    Didn't get what you wanted or have a problem? We understand that sometimes things aren't right and our team is serious about resolving these issues quickly. We can often help you fix small to medium issues over the phone or email.

    If you need to return an item please read our return policy.

    Learn About Returns

Get FREE shipping on qualifying orders! Any order $150+ with a shipping address in the contiguous US will receive the option for free ground shipping on items sold & shipped by Pyramyd AIR during checkout. Certain restrictions apply.

Free shipping may not be combined with a coupon unless stated otherwise.

View Shipping Info

Text JOIN to 91256 and get $10 OFF Your Next $50+ Order!

* By providing your number above, you agree to receive recurring autodialed marketing text msgs (e.g. cart reminders) to the mobile number used at opt-in from Pyramyd AIR on 91256. Reply with birthday MM/DD/YYYY to verify legal age of 18+ in order to receive texts. Consent is not a condition of purchase. Msg frequency may vary. Msg & data rates may apply. Reply HELP for help and STOP to cancel. See Terms and Conditions & Privacy Policy.