- Home
- Air Gun Manuals
- DPMS-M4-A1-CQBR-17934
Panther Carbine CQBR Colt M4-A1 Airsoft Rifle Owner's Manual
Panther Carbine CQBR Colt M4-A1 Airsoft Rifle
| Weight: 6.50 lbs Overall Length: 28.50" Capacity: 300 round(s) Item # 17934 |  |
Panther Carbine Colt M4-A1 Reloading
 To release the magazine, push on the lock located on the side and slide the magazine out of the rifle. |  Open the upper cover and load the magazine as shown on the picture. The maximum capacity is about 300 rounds. |
 Rotate the wheel located at the bottom of the magazine as shown by the arrow in this illustration. Totate until a "click" is heard. Once the available rounds are shot, repeart in order to replenish the feeding mechanism magain. Repeat at will. |  This first step will convey BBs from the storage compartment of the magazine (holds up to 300 rounds) to the feeding mechanism of the magazine for immediate use. |
 Close the tab and slide the magazine in the receptade until it is locked (a distinct click will be heard). | |
| back to top | |
Panther Carbine Colt M4-A1 Setting the Battery
 First, remove the rubber stock cover. |  Unscrew as shown. |
 Press on 2 flaps simultaneously to remove the lid. | |
 Install the split battery in the stock and plug the connector. | |
 | Take care to arrange the wires properly as shown on picture. |
 Put back the stock cover. Take care to arrange the wires in the notch of the cover as shown on the pictures. It's possible the stock does not entery totally. Do not insist, you can damage the wires. | |
 | To put back the cover, reverse the initial operations. |
| back to top | |
Panther Carbine Colt M4-A1 Installing the Grip
 To install the vertical grip, unscrew the base of the grip and slide the grip in the rail. Then, take care to place your vertical grip in a right position(in right position, you can see the free position through the hole). Screw the base to stop the grip. | |
| back to top |
Panther Carbine Colt M4-A1 Protection Panel
 Slide the protection panel on the rail and lock it by pushing on the spring as shown on the pictures. To remove it, you have first to push on the spring. | |
| back to top |
Panther Carbine Colt M4-A1 Firing
 To start shooting, aim at a target, put the selector on the "semi" or "auto" position. Pull the trigger. Once the available rounds are shot, repeart step 3 in order to replenish the firing compartment again. Repeat at will. | |
| back to top |
Panther Carbine Colt M4-A1 Hop Up
 | To adjust the Spin Up / Hop Up Accuracy system, pull the loading handle back to reach the Spin Up / Hop Up adjustment. |
 | Turn this screw to adjust the Spin Up / Hop Up and to fine tune your shot, according ammo weight and weather conditions. |
| back to top | |
Panther Carbine Colt M4-A1 Rear Sight
 Unscrew slightly the screw of the rear sight support. Then, slide the rear sight on the rail and lock with the mentioned screw. |  Rear sight can be adjusted in elevation and windage. |
| back to top |
Panther Carbine Colt M4-A1 After Shooting
 | Once finished shooting, put the shooting selector back on the "Safe" position. Make sure the rifle is stored empty of any ammunition, magazine removed. |
| back to top | |
Panther Carbine Colt M4-A1 Charging the Battery
 | Plug your battery pack on the small charger and plug this small charger on 110 or 220 volts. If your pack is empty, it will need between 2 and 3 hours to be fully charged. TIP: Do not forget that any pack which begins to rise in temperature after a certain period of charge is a battery pack fully charged. Caution:Do not charge more than 3 hours. |
| back to top | |
Caution
 |
| CAUTION DISASSEMBLING (TAKING APART) THIS SOFTAIR PRODUCT VOIDS ALL WARRANTY. PRODUCT MUST BE RETURNED IN ITS ORIGINAL PACKAGING. FEDERAL LAW PROHIBITS ALTERING OR REMOVING THE ORANGE MARKING OR PAINTING OVER THE TRANSPARENT PART OF THIS PRODUCT. Do NOT use 6mm paintballs with this softair. Shooting paintballs with this unit will result in jamming and will void warranty. Warning |
| back to top |