M100 Spring Airsoft Gun Sniper Rifle Owner's Manual

M100 Spring Airsoft Gun Sniper Rifle

Features adjustable hop-up
Functional Safety & Adjustable Rear Sight
M14 Spring Airsoft Gun Sniper Rifle
M100 Airsoft Rifle Components
M100 Airsoft Rifle Safety
M100 Airsoft Rifle Loading BB Bullet
M100 Airsoft Rifle Operation
M100 Airsoft Rifle Setting the Open Sight
How to AIM/HOLD
M100 Airsoft Rifle Maintenance
M100 Airsoft Rifle Caution
M100 Airsoft Rifle Components
1 Flash Suppressor 9 Magazine
2 Suppressor Lock 10 Bolt Stop
3 Front Sight 11 Rear Sight
4 OuterBarrel 12 Safety Lever
5 Gas Cylinder Plug 13 Trigger
6 Front Swivel 14 Rear Swivel
7 Hand Guard 15 Stock
8 Hand Guard Rear Band    

M100 Airsoft Rifle Safety

TSD M100 Airsoft Rifle Safety

(Always set the safety lever to safe position before firing)

When you are not firing the gun or during storage, always set the selector to the Safe position and attach the protective cap to the muzzle.

TSD M100 Airsoft Rifle Safety

When the safety lever is set to the "On" position, the trigger will not move. Please do not pull the trigger, otherwise you may damage the gun.

When the safety lever is set to the "Off" position, it is ready for shooting.

The gun will fire when the trigger is pulled.

back to top

M100 Airsoft Rifle Loading

TSD-Sport-M100 Airsoft Rifle Loading

Installation

Always set the magazine upwards. First hook the hook in the front of the magazine and then press in the rear of the magazine until a sound of "click" is heard.

TSD M100 Airsoft Rifle Loading

Removing the Magazine

Press the magazine release lever to remove the magazine.

Caution

Be sure that the safety lever is set to the Safety position and don't place your finger on the trigger except when you are ready for shooting.

TSD M100 Airsoft Rifle Loading

Load BB's into Speedloader

Open the Speedloader Cap. Insert 6 mm BB'S into the Speedloader.

Press the Rod Release button to release the Spring Rod.

Insert Speedloader into the magazine and pump Spring Rod until magazine is full.

back to top

M100 Airsoft Rifle Operation

TSD Sport M100 Airsoft Rifle Operation

The bolt retracts at the same time the operating rod is pulled.
To fire the gun, pull back Operating Rod all the way back, until a "click" is heard, then release.
Make sure the Safety release is in "Off" position. The gun is now ready for firing.
Pull Trigger.
Replace Safety release to "On" position when the gun is not in use.

Warning. Caution
Be careful not to put your finger in the bolt as it will close quickly when the operating rod is released.

back to top

M100 Airsoft Rifle Setting the Open Sight

TSD M100 Airsoft Rifle Setting the Open Sight

Elevation adjustment

Turning counterclockwise lowers the bullet hitting point.

Turning clockwise raises the bullet hitting point.

Turning the elevations adjustment dial will move the bullet hitting point to the uppers or lower.

M100 Airsoft Rifle Setting the Open Sight

Windage adjustment

Turning clockwise moves the bullet hitting point to the left.

Turning counterclockwise moves the bullet hitting point to the right.

Turning the windage adjustment dial will move the bullet hitting point to the left or to the right.

back to top

How to AIM/HOLD

SDM100 Airsoft Rifle How to AIM/HOLD

How to Aim

Look through from the front sight to the hole of the rear sight, and aim at the center of the target.

TSD M100 Airsoft Rifle How to AIM/HOLD

How to hold

Press the butt plate against slightly inside of the shoulder joint and put your cheek on the stock. Aim at the center of the target as shown in the figures.

Be careful not to put your fingers in the moving parts.

back to top

M100 Airsoft Rifle Maintenance

Maintenance when bull speed becomes low

1. Apply Oil as shown below, using the cleaning rod and oiled cotton cloth. Insert cleaning rod into barrel.
2. After completeing cleaning, use the cleaning rod (with cotton) as shown below to Remove excess oil.

SDM100 Airsoft Rifle Maintenance
Hold at the leading end of the rod and insert the rod into the barrel while turning the rod.

Caution
Always turn the hop up lever completely down before inserting Cleaning Rod.
It is difficult to insert the rod if you hold the rod at the end.

Removing Clogged Bullets (Set the Safety button to ON and remove the magazine beforehand.)

1. Remove the Magazine

SDM100 Airsoft Rifle Maintenance 2. Turn the hop up dial completely down and insert the Cleaning road from the lead edge of the barrel.
SDM100 Airsoft Rifle Maintenance 3. Be careful so that the angled part of the Cleaning Rod faces down, and remove clogged bullets

Make sure to clean the barrel chamber whenever bullets are removed.

When bullets are clogged, immediately stop operation, remove clogged bullets and then restart operation of the air gun. (If operation is continued with bullets being clogged, the mechanism may be damaged.)

Be careful during maintenance, as the inside chamber is precisely designed and can be damaged easily. Use of a hard brush may damage the hop chamber packing.

back to top

M100 Airsoft Rifle Caution

Wear protective eye wear and face mask when playing Airsoft Sports.
NEVER brandish or fire Airsoft Sport Gun at animal or people beyond a certified and regulated Airsoft Sport arena. Brandishing a gun in public is against the law, serious consequences could arise.
Read and understand the operating and safety manual before using your Airsoft Sport Gun.
Do not look directly into the gun barrel to avoid accidental discharge of BB.
Be aware of your surroundings to avoid accidents.
ALWAYS transport an Airsoft Sport Gun inside a locked carrying case. Make sure it's unloaded. Never carry your Airsoft Sport gun in open view as a concealed weapon, or brandish an Airsoft Sport Gun in public.
Do not disassemble or modify your Airsoft Sport Gun doing so will void all warranty Service by authorized centers only. Removal of the orange safety barrel marking is a federal offense.
Always install safety barrel plug when you are not using your Airsoft Sport Gun.
back to top
Navigation