SHADOW OPS SNIPER UTG S368 Owner's Manual

 

TECHNICAL DATA

Hop Up: Adjustable
Effective range: 100 yd
Length: 48.4inches (1230.0 mm)
Weight 8.5 lbs
Magazine Capacity: 23
Type: Bolt ActionVelocity:
465 fps with .20g BBs
415 fps with 0.28g BBs
310 fps with 0.43g BBs


      Component Chart
      1. Fire/Safety Selector
      2. Trigger
      3. Cocking Handle
      4. Upper Picatinny Rail
      5. Hop-up Adjustment Switch
      6. Barrel
      7. Double Detachable Butt Pads
      8. Adjustable Cheekpiece
      9. Magazine Release Lever
      10. Double Magazines
      11. Tri-Rail Bipod Adaptor
      12. Allen Wrench
      13. Deluxe Tactical Bipod

Warning! Before you follow the assembly instruction , make sure to remove the magazine and set theFire/Safety Selector to the "SAFE" position.

Assembly

- Install Kit A (Receiver& Barrel) into Kit B
(Stock) (Fig 2.1).
- Lock Kit A into Kit B with built-in screws
and provided M5 AIlen Wrench. Make
sure to tighten screw B first before
tightening screw A to prevent installation
difficulty (Fig 2.2).
- Insert the Tri-Rail Bipod Adaptor into the
Housing of the front handguard under the
barrel (Fig 2.3 and Fig 2.4). Make sure it
click and is fully engaged
.

Adjust Cheekpiece and Butt Pad
To Adjust the Height of the CheekpieceLocate and loosen up the two Hex Screws on the stock with the provided M5 Allen Wrench. Pull the cheekpiece up to a desired position, then tighten the hex screws (Fig 3.1).

To Adjust the Thickness of the Butt Pad
Locate and remove the two Hex Screws on the Butt Pad Cover.Remove one or both middle layers based on your preference. Replace and tighten the Butt Pad cover with the provided M5 Allen Wrench

(Fig 3.2).

Load BBs

Warning! Always use NeonFire Premium Precision Ground 6mm

BBs for accuracy and safety. Never re-use BBs.

*Disengage the magazine by pressing the Magazine Release Lever. (Fig 4.1)
*Feed BBs into the magazine through Pellet Drop. (Fig 4.2)
* Insert the loaded magazine back into the rifle.

Install Bipod

Make sure the Tri-Rail Bipod Adaptor is installed first. Mount the deluxe tactical bipod onto the Tri-Rail Bipod Adaptor (Fig 5.1).

Install optional accessories

The airsoft rifle comes with a great quality Picatinny Rail and a Tri-Rail Bipod Adaptor for installing your accessories such as scope, bi-pod, flashlight, laser sight or others. To mount accessories, please follow their respective instructions.


1. Mount on Picatinny Rail

Locate the Tri-Rail Bipod Adaptor on the front hanguard. Align and mount the Bipod into the bottom Picatinny rail. Make sure the locking bolt at the clamping head of the bipod sits into one slot of the rail. Then tighten the thumb screw to fully secure the Bipod.

2. Panning and Foldable
Press down the Posi- Lock Button to fold or unfold bipod legs. Unique Posi-Lock feature prevents tipping. Bipod pans for easy aiming adjustment.

3. Fully Extendable

Unscrew the nut and adjust the length. Once done, tighten the nut to lock the legs.

Firing (Ensure complete safety of environment before firing.)
Activating the trigger carelessly is extremely dangerous. Never set the Safety/Fire Selector off the "SAFE" position or put your finger on the trigger unless the protective plug is removed and you are ready to shoot at a target.


Shooting Operation
-Set Fire/Safety Lever to "Fire" position.(Fig7.1)

-Pull the cocking handle upward and all the way back until it clicks.

Then push it back to the original position to complete cocking in one continuous movement.

-Hold the gun firmly and rest the stock at a comfortable position.

- Aim the rifle at your target and pull the trigger to fire.

 

Adjust Variable Hop-up System for Best Shooting
- Locate the Hop-up Adjustment Screw at the front of the magazine. (Fig 7.2)
- Use provided M2.5 Allen Wrench to adjust the Hop-up to a desired state by tightening down clockwise or loosening up counter-clockwise.
- Shoot a few pellets, exam the trajectory and make further adjustment if necessary.

Maintenance

*Keep the rifle in clean condition.
*Regularly clean the barrel with soft cleaning rod.
*Never use dirty, damaged or distorted BBs.


HomeSearchBrowseAboutContactFAQ
ManualsCustom Venom ShopPrivacy StatementLinks
Shop at Gun Mall
Shopping Cart Items

    CheckoutSubtotal (USD):
    does not include shipping and tax

    Back to Top