*Offer expires 04/30/24 at 3 a.m. ET. Some exclusions apply.
Create an online review and share your thoughts with other customers
5.0 5.0
5.0 5.0
By Jeff from USA on 2014-04-12 16:27:33
Well made, very precise, looks terrific, mounts tightly. Other mounting systems I've tried leaned to the left a bit, but not this one! It has two stop screws, four clamping screws, and decent drop compensation.
Things I would have changed:I had to trim the "wedges" that actually fit into the dovetail, on the rear of the unit. I only found this necessary to get the rail back far enough on the receiver. I'm sure most guns won't have this problem, but one of mine needed the mount to go all the way to the back of the dovetail, where it actually widens before ending (look at yours, you'll see what I mean). Not a big deal, just a few minutes with a Dremel tool, and all is well. Probably wouldn't be necessary with a longer scope.
What others should know:Well worth the money, and easy to install. Bear in mind that this adapter will raise your scope height about 15mm/little more than half an inch, so think of that when you're ordering scope mounts. Most scopes seem to come with "medium" rings, so I suggest buying a set of short rings as well, to make sure you can achieve a proper cheek weld.
1.0 1.0
1.0 1.0
By Marc Bruno on 2023-08-01 17:48:51
Comes with one extra mounting bolt and one extra anti-slip pin. Its full-length and has four mounting bolts.
Things I would have changed:The cross-sectional manufacturing specs need to be adjusted, because the base was clearly NOT MOUNTING DIRECTLY OVER THE BORE. It looked about 1/8-inch to the left (the bolt side) of center on the 11mm dovetail that came on my RWS Model 54.
What others should know:I tried several different rings in an attempt to compensate for the deviation, but nothing worked. Also, FYI, the older one-piece, ring/mount unit that I used to use didnt have this problem, so I know that the 11mm dovetail that came on the rifle is indeed centered.
Sort by: | Date
| Helpfulness
| Rating
|
---|
Filer by: |
---|
5.0 5.0
5.0 5.0
Verified Purchase
This scope rail fit my Diana 48 T-6 perfectly and allowed me to mount Weaver type rings to the rifle. The mount has stop pins that fit the Diana 48 perfectly and the rail locks to the dovetail like a bank vault.
Things I would have changed:No changes.
What others should know:This mount might have a little too much droop compensation for my rifle and I might try rings or a mount with no droop compensation to compare the difference in scope adjustment.
5.0 5.0
5.0 5.0
Verified Purchase
Very well made
What others should know:Installed this on a RWS Mod 45 that I purchased when I was kid. Not realizing this model didn’t need compensation for barrel droop. Got too much elevation could not adjust scope to low enough. I reinstalled it in reverse to raise scope and it works perfectly no movement whatsoever
1.0 1.0
1.0 1.0
Verified Purchase
Comes with one extra mounting bolt and one extra anti-slip pin. Its full-length and has four mounting bolts.
Things I would have changed:The cross-sectional manufacturing specs need to be adjusted, because the base was clearly NOT MOUNTING DIRECTLY OVER THE BORE. It looked about 1/8-inch to the left (the bolt side) of center on the 11mm dovetail that came on my RWS Model 54.
What others should know:I tried several different rings in an attempt to compensate for the deviation, but nothing worked. Also, FYI, the older one-piece, ring/mount unit that I used to use didnt have this problem, so I know that the 11mm dovetail that came on the rifle is indeed centered.
5.0 5.0
5.0 5.0
Verified Purchase
Well made and easy to install
Things I would have changed:Make it longer by 3/4 inch
What others should know:Use this if you are scoping a break barrel rifle.
5.0 5.0
5.0 5.0
Verified Purchase
I bought the UTG Drooper Scope Rail, 11mm-to-Weaver Adapter for my RWS 34 Classic to mount a rifle scope I already had. Easy to install, scope mounted good and it is high enough that removal of the open sights was not necessary, it all looks good together as well.
Things I would have changed:Nothing at this point.
What others should know:The rail is sturdy, mounts easily and looks good. I have not had it long or used it enough to know how it will hold up over time though it seems it will last as long as the rifle.
5.0 5.0
5.0 5.0
Verified Purchase
Good price, extra screws.
Things I would have changed:None
What others should know:Needed a different base for new scope and rings and this works very well.
5.0 5.0
5.0 5.0
Verified Purchase
I hadn't experienced 'barrel droop' prior to purchasing a Ruger/Umarex break barrel rifle. This mount most definitely corrects it. At 50', even after turning the elevation a half-turn down, I was still hitting the top of the target. Now I'm shooting 'ragged hole' groups with the H&N Barracuda Hunter Extreme, and dead center at that, with a gun that's definitely NOT a target rifle. There's also been no movement of the scope or the mounts. This mount really does the job.
Things I would have changed:Nothing that I could think of.
What others should know:If properly torqued, the four screws on this mounting system will prevent scope/mount movement, even if there are no holes in your receiver for the staking screws in the center of the mount.
5.0 5.0
5.0 5.0
Enables you to adjust scope turret spring to high tension and still have enough elevation when sighting in scope. This helps prevent scope reticle shift.
Things I would have changed:Nothing
5.0 5.0
5.0 5.0
Verified Purchase
Excellent quality. Did what its intended to do fixed my droop.
Things I would have changed:Nothing
What others should know:Mounted on Diana 45/.177 Tuned with Hawke 3-9x40 AO with UTG high strength quick detach. Was Leary of the rings at first. Re -Centered scope via V blocks. Shot 5 HN baracuda match @ 20 . Elevation 0 windage 1.5 Rt.1/2 group. Bench. I was amazed not much adjustment at all . 50 rounds later no movement at all on any ring or base mount Marks. I still cant Get over how little scope adjustment I needed to zero. V blocks are more accurate then the mirror or counting for Centering. Make a good one out of wood with a decent size base and clamp it down.
4.0 4.0
4.0 4.0
have so many different types airguns this will work with, fast easy
1.0 1.0
5.0 5.0
Had great potential to be a good transition from the 11mm dovetail to the Weaver adapter rail. The four hex screws on the Weaver adapter rail made for a firm attachment to the dovetail.
Things I would have changed:Description said this was for RWS rifles, but that it would fit any 11mm scope dovetail rail. It did not fit my Weihrauch 35 air rifle b/c only 1 of the stop pins lined up with the "holes" in my HW35. The stop pin that screwed down into the "hole" was not the right size/width/depth, therefore not a snug fit b/c it didn't fill up the hole in my Weihrauch 35. If I knew what to replace it with, I would. Should have been a picture of the bottom side or a better one from the top showing where the spacing was for the stop pins. I was able to use only the rear stop pin and I'm apprehensive it won't last for the long-term. Also, there were no directions on the correct direction to put the adapter rail on so I had to take everything off and reverse it when I found out my Hawke scope wouldn't adjust for correct POI. I didn't know whether the writing on one side of the adapter rail went on the left side or right side, haha! Sorry, I'm a retired 69 yrs old guy, new to air guns.
What others should know:Check spacing & measurements of the stop pins.
2.0 2.0
2.0 2.0
Seem to be good quality and clamp tight.
Things I would have changed:Did not give me enough elevation on a cheap break barrel Crosman.
5.0 5.0
5.0 5.0
solid 4 screw mount and seems well made and fit perfect
Things I would have changed:nothing
What others should know:fits my 11mm rail good and solid. I recommend it
4.0 4.0
5.0 5.0
Verified Purchase
Strong, light weight, quality construction. Nothing fancy, it does the job it was designed to do.
Things I would have changed:nothing
What others should know:I mounted a 3-9x40 scope using low profile rings and this droop compensating rail to a vintage Diana Model 34. This rail brought the scope vertical adjustment down below the mid-point.
5.0 5.0
5.0 5.0
A must have if you own a Diana break-barrel air rifle and plan on using a scope with it.
Things I would have changed:Nothing
What others should know:Installing a UTG AccuShot SWAT 4-16 x 56 scope I used Medium Leapers AccuShot 30mm Rings.
1.0 1.0
1.0 1.0
Verified Purchase
Inexpensive
Things I would have changed:Construction quality.
What others should know:Had this on a swarm magnum .22! Complete failure and the company would not stand behind it.. Perhaps it wasn't designed to handle Mangum rifles!
5.0 5.0
5.0 5.0
Verified Purchase
Great mount. Solved barrel droop issue. Great price point
Things I would have changed:Nada
What others should know:Put on my Hatsan Proxima and thats where it will stay. Had barrel droop issue at 25 yds. With this mount, I was able to dial in at 40 yards with nickel sized groups on a mostly calm day. Thats outstanding for .177 7.9gr CPHP. 16+ ft/lb energy at muzzle
5.0 5.0
5.0 5.0
Does what it says
4.0 4.0
4.0 4.0
Verified Purchase
It is built good.
Things I would have changed:Nothing
Buy With Confidence
Get FREE shipping on qualifying orders! Any order $150+ with a shipping address in the contiguous US will receive the option for free ground shipping on items sold & shipped by Pyramyd AIR during checkout. Certain restrictions apply.
Free shipping may not be combined with a coupon unless stated otherwise.
View Shipping Info
We work hard to get all orders placed by 12 pm EST out the door within 24 hours on weekdays
because we know how excited you are to receive your order.
Weekends and holiday shipping times will vary.
During busy holidays, we step our efforts to ship all orders as fast as possible,
but you may experience an additional 1-2 day delay before your order ships.
This may also happen if you change your order during processing.
View Shipping Times
It's important to know that due to state and local laws, there are certain restrictions for various products.
It's up to you to research and comply with the laws in your state, county, and city.
If you live in a state or city where air guns are treated as firearms you may be able to take advantage of our FFL special program.
U.S. federal law requires that all airsoft guns are sold with a 1/4-inch blaze orange muzzle
or an orange flash hider to avoid the guns being mistaken for firearms.
View Shipping Restrictions
Get the most out of your equipment when you work with the expert technicians at Pyramyd AIR. With over 25 years of combined experience, we offer a range of comprehensive in-house services tailored to kickstart your next adventure.
If you're picking up a new air gun, our team can test and tune the equipment before it leaves the warehouse. We can even set up an optic or other equipment so you can get out shooting without the hassle. For bowhunters, our certified master bow technicians provide services such as assembly, optics zeroing, and full equipment setup, which can maximize the potential of your purchase.
By leveraging our expertise and precision, we ensure that your equipment is finely tuned to meet your specific needs and get you ready for your outdoor pursuits. So look out for our services when shopping for something new, and let our experts help you get the most from your outdoor adventures.
View Service Info
Shop and purchase with confidence knowing that all of our air guns (except airsoft) are protected
by a minimum 1-year manufacturer's warranty from the date of purchase unless otherwise noted on the product page.
A warranty is provided by each manufacturer to ensure that your product is free of defect in both materials and workmanship.
View Warranty Details
Didn't get what you wanted or have a problem? We understand that sometimes things aren't right and our team is serious about resolving these issues quickly. We can often help you fix small to medium issues over the phone or email.
If you need to return an item please read our return policy.
Learn About Returns
Get FREE shipping on qualifying orders! Any order $150+ with a shipping address in the contiguous US will receive the option for free ground shipping on items sold & shipped by Pyramyd AIR during checkout. Certain restrictions apply.
Free shipping may not be combined with a coupon unless stated otherwise.
View Shipping Info
Want More?
Join Our Email List for News and Deals!
Join the Pyramyd AIR mailing list: Our e-mails are filled with new products, deals, sneak peeks, tips and tricks, contests and more - sign up today!
Text JOIN to 91256 and get $10 OFF Your Next $50+ Order!
* By providing your number above, you agree to receive recurring autodialed marketing text msgs (e.g. cart reminders) to the mobile number used at opt-in from Pyramyd AIR on 91256. Reply with birthday MM/DD/YYYY to verify legal age of 18+ in order to receive texts. Consent is not a condition of purchase. Msg frequency may vary. Msg & data rates may apply. Reply HELP for help and STOP to cancel. See Terms and Conditions & Privacy Policy.
By Michael
5.0 5.0
5.0 5.0
Verified Purchase
This thing "fixed" my Crosman Shockwave. I could not get the aim down for anything, until I used this rail. I highly recommended it.
Things I would have changed:As it was not designed for my Crosman, I did have to file an 1/8" off the end to make it fit. But it fit well.
What others should know:Highly recommend.