Date: 28/3/2024 20:56

Leapers Accushot 1-Pc Bi-directional Offset Reviews

Leapers Accushot 1-Pc Bi-directional Offset Mount w/1" Rings, High, 11mm Dovetail

Average Customer Review

Rating 4.54.5 (86 reviews)
Add to Cart

Only 3 left in stock

Create an online review   and share your thoughts with other customers

The most helpful favorable review

1 of 1 people found the following review helpful:

Rating 5.05.0 5.0

Rating 5.05.0 5.0

By Alan from USA on 2009-01-07 20:17:01

Things I liked:

Cheap and good quality as usual with Leapers products, particularly their mounts.

Things I would have changed:

Nothing.

What others should know:

This mount is a must if you are purchasing one of the Leapers Bugbuster scopes. Without it the eye relief will be all wrong for comfortable shooting on any rifle.

The most helpful critical review

0 of 0 people found the following review helpful:

Rating 1.01.0 1.0

Rating 2.02.0 2.0

By Clint from USA on 2021-07-08 21:04:16

Things I liked:

The finish is nice and it comes with tools and extra screws

Things I would have changed:

The clamp itself is extremely weak

What others should know:

I used this to mount a Hawke scope to a gas piston Hatsan 95 and was confused as to why I couldn't seem to get a consistent zero until the scope stop block and two screw heads fell in my lap. Before installing it, I cleaned the oil off the screws and then applied blue threadlocker but the mount, with the clamp and set screws tightened, still moved back with enough force to make a large impression in itself and eventually shear off the two bolts holding the block. I dry fired the gun and watched as the mount walked back with each shot. In all, it was not only completely unusable on my gun, it also broke the screws off in the holes and marred the barrel where the set screws slid back.

Sort by:
Filer by:
  • 12345 Next
  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Verified Purchase

    Things I liked:

    Good Quality

    Things I would have changed:

    Nothing

  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Verified Purchase

    Things I liked:

    Good quality construction. Perfect for mounting my UTG Bug Buster compact scope. Brings the scope back far enough for perfect eye relief.

    Things I would have changed:

    Nothing

    What others should know:

    11 mm dovetail mount.

  • Rating 1.01.0 1.0

    Rating 2.02.0 2.0

    Things I liked:

    The finish is nice and it comes with tools and extra screws

    Things I would have changed:

    The clamp itself is extremely weak

    What others should know:

    I used this to mount a Hawke scope to a gas piston Hatsan 95 and was confused as to why I couldn't seem to get a consistent zero until the scope stop block and two screw heads fell in my lap. Before installing it, I cleaned the oil off the screws and then applied blue threadlocker but the mount, with the clamp and set screws tightened, still moved back with enough force to make a large impression in itself and eventually shear off the two bolts holding the block. I dry fired the gun and watched as the mount walked back with each shot. In all, it was not only completely unusable on my gun, it also broke the screws off in the holes and marred the barrel where the set screws slid back.

  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Things I liked:

    Just mounted this on a hatsan 95 . I needed lots of backset .This mount is working great with a utg scope. Seems like a strong mount.

    Things I would have changed:

    None

    What others should know:

    Seems like a good strong mount

  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Things I liked:

    Easy to install.

    Things I would have changed:

    Nothing

    What others should know:

    Used this to mount a bug buster scope, worked great.

  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Things I liked:

    Economic. Sturdy. Distance between rings fits compact scope and off set makes up for short eye relief...see image

    What others should know:

    I put this on a tuned Hat 135 .30 cal w/ the ram filled to 150bar. Wernt room to use Hatsan scope stop. This mount comes w/ a scope stop pin. I used blue loc tite on it. Cause it backed out and i had to remove scope and re zero. Since i used blue loc tite, it hasnt budged. Ram filled to 150bar = more recoil. So it works. Probably cant get a better example of it working = much recoil. Most likely wont work w/ a full size scope=The distance between rings is just right for compact.

  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Things I liked:

    Everything, quality is great

  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Things I liked:

    I purchased this offset mount w/rings to put on my gamo swarm magnum and on my gamo swarm maxxium rifles so my utg 3x9 scopes would set back on the rifles so i wouldnt have to crunch up on the stock to get a good view through the scope. the scope stop pin lined up perfect and now have a comfortable view through the scopes at all powers.

  • Rating 2.02.0 2.0

    Rating 1.01.0 1.0

    Things I liked:

    The over all finish. A fine looking mount.

    Things I would have changed:

    More clearance from the bottom of the rings to the base.

    What others should know:

    I am really disappointed with this mount. Maybe if I had looked at the picture more closely I would have seen that the rings are so low to the base. Take a look at the picture to see what I mean. I placed the mount on my Benjamin Titan NP and it mounted with a slight lean to the right. Not quite square with the rifle. Not a big deal, but. I then mounted a UTG 3-12 AO Bug Buster scope. The bulge in the scope where the adjustment are located just barely cleared the base of the mount. It was so close I could not rotate the scope far enough to compensate for the tilt of the mount. I tried the mount on a Crosman 1077 and an old QB77 side lever, and had the same problem. I also reversed the moveable clamp trying to get it to mount more square with one of my rifles but to no avail. I did not think at the time, I could have shimmed both rings to try to get the scope high enough to rotate enough to square the reticle with the rifle. By then I had already ordered a UTG Leapers MNT-DTW145

  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Things I liked:

    Fits a Bugbuster scope to a Diana Chaser very well, allowing use of the Chaser magazine on the pistol or rifle. Very secure mount of good quality, and adjustable for eye relief.

    Things I would have changed:

    -

    What others should know:

    -

  • Rating 3.03.0 3.0

    Rating 3.03.0 3.0

    Things I liked:

    Gives great eye relief for compact scopes like the bug buster.

    Things I would have changed:

    The scope stop screw was drilled on an angle.

    What others should know:

    These work great for eye relief on compact scopes. I am using it on a low powered gun so didnt use the stop screw that is drilled on an angle. Check the screw if your using it on a high power springer.

  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Things I liked:

    You really need this to mount the Bug Buster on the Gamo Swarm.

    Things I would have changed:

    Nothing

  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Verified Purchase

    Things I liked:

    I purchased these Rings to use with the UTG Bug Buster Scope to get better eye relief. They did not disappoint. Worked as planned. Very solid quality Mount!

    Things I would have changed:

    Nothing

  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Things I liked:

    Very well made,has the stop pin for Air rifle, you can't beat it for the price.

    Things I would have changed:

    Nothing

    What others should know:

    I would definitely recommend this. I'm most likely gonna get another.

  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Verified Purchase

    Things I liked:

    Simple and solid with duel stop pins

    Things I would have changed:

    Notta

    What others should know:

    Perfect for getting my new side paralex bug buster back for the right eye relief on my HW 30. I think it would work well on other guns and scopes. The distance between the stop pins is 3/4",

  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Things I liked:

    This mount worked great on my Norrica Massimo break barrel. I was having issues with correct eye relief. This was certainly the ticket. gives you plenty of eye relief adjustment either direction, just flip it around.

    Things I would have changed:

    Nothing

  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Things I liked:

    I have several of these mounts. I use them to bring a short scope back within the eye field of view. Very stable and secure mount.

    Things I would have changed:

    I have had no problems with this mount, so for me no change needed.

    What others should know:

    I find that for me the end of the scope needs to be about nine inches from the butt of the rifle. This allows me to make that adjustment.

  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Things I liked:

    Works great for forward mounting of scope to gain loading clearance on FWB 300"s.

    Things I would have changed:

    Nothing.

  • Rating 5.05.0 5.0

    Rating 5.05.0 5.0

    Things I liked:

    Great mount for FWB 300S for mounting scope far enough ahead to load pellet. Scope is Vortex 6X-18X with 44mm AO.

    Things I would have changed:

    Nothing.

  • Rating 4.04.0 4.0

    Rating 4.04.0 4.0

    Things I liked:

    I had a UTG BugBuster 3-9X32 AO scope that needed to be mounted farther back on my HW30S. This offset mount worked perfectly. It's not as nicely finished as more expensive mounts, but it is worth the money (the same can be said for the scope, too)

    Things I would have changed:

    Nothing.

    What others should know:

    Someone said the mount did not work with the latest version of the BugBuster scope. I have the latest version and it fit mine perfectly, but there is very little room to rotate the scope in the mount. This wasn't a problem as I still had plenty of adjustment to get the reticle vertical.

  • 12345 Next

Buy With Confidence

Get FREE shipping on qualifying orders! Any order $150+ with a shipping address in the contiguous US will receive the option for free ground shipping on items sold & shipped by Pyramyd AIR during checkout. Certain restrictions apply.

Free shipping may not be combined with a coupon unless stated otherwise.

View Shipping Info

Want More?

Join Our Email List for News and Deals!

Join the Pyramyd AIR mailing list: Our e-mails are filled with new products, deals, sneak peeks, tips and tricks, contests and more - sign up today!

Text JOIN to 91256 and get $10 OFF Your Next $50+ Order!

* By providing your number above, you agree to receive recurring autodialed marketing text msgs (e.g. cart reminders) to the mobile number used at opt-in from Pyramyd AIR on 91256. Reply with birthday MM/DD/YYYY to verify legal age of 18+ in order to receive texts. Consent is not a condition of purchase. Msg frequency may vary. Msg & data rates may apply. Reply HELP for help and STOP to cancel. See Terms and Conditions & Privacy Policy.