








Mendoza Front Sight Riser Assembly For Air Venturi Bronco
PY-A-4182
Not Available
View more products from Mendoza
Description
- Riser assembly
- Slides under the front sight of an Air Venturi Bronco
- Includes 4 plates and 2 long screws
- Raises front sight to match the elevation level of a Bronco fitted with the Mendoza rear peep sight (ME-555-12-1000)
The Air Venturi Bronco is an accurate rifle that's easy to shoot. If you'd like to upgrade your Bronco to the Mendoza rear peep sight (ME-555-12-1000), you'll have to raise the Bronco's front sight to the correct elevation so you can see it with the upgraded rear sight. These 4 riser plates will do that. The front sight screws that came with your Bronco will not be long enough to attach the plates, so we're including 2 longer screws.
Specifications
Overall Rating
Review This Product
Tell us what you think
5 of 5 Mendoza Front Sight Riser Assembly Reviews
Allows you to lift the front sight to enable you to better center the rear aperature sight.
Things I Would Have Changednothing
What Others Should KnowElevating the sight plain a little on the Bronco was necessary for me due to my large face (fat face) and the design of the straight stock. I really do like the straight stock of the Bronco. Reminds me of an 1903 springfield battle rifle.
Metal construction and quality black finish exceeded my expectation for the parts. All required hardware included.
Things I Would Have ChangedIf you want the target special sights get the Bronco Target Special rifle instead of the parts. A small sheet of instructions noting wrench size and an installation illustration would ease fears of the mechanically disinclined.
What Others Should KnowPerfect solution to raise the front sight of the Air Venturi Bronco front sight for use with the Mendoza 11mm dovetail mount diopter rear sight. If you don't already have a Bronco and want the target sights buy the Target Special instead of the standard Bronco.
Well made. Very easy to install. Remove the two stock front sight screws with a 3/32" Allen wrench slip on the plates and new longer screws and re-tighten. Mine had a tiny bit of side slip so watch that as you tighten down the screws to make sure the sight blade points straight up.
Things I Would Have ChangedMy concern is the longer screws damaging the shot tube if you don't use all four plates. The included screws are for four plates to work with the Mendoza sight, and seem to work with two plates on my Bronco and Beeman peep. I don't think the screws are pressing on my shot tube, but it would be nice to include additional screws that were shorter for use with two plates or even one plate to accommodate other peep sights.
What Others Should KnowI used two of these plates to raise the front sight to work with a Beeman peep site. Before, I had the peep bottomed out to get on target. Two of these plates put the sight in the middle of its adjustment range. Apparently with the Mendoza peep you need four plates. Other peep sights may not need all four plates.
Nicely matches the Mendoza peep sight. Easy to install.
Things I Would Have ChangedAn alignment pin in the sight and the Bronco.
What Others Should KnowA little slop in alignment allows it to be installed with a slight tilt. You may need to apply side pressure when tightening the mounting screws.
Get FREE shipping on qualifying orders! Reach your tier's spend threshold to unlock free ground shipping on items sold & shipped by Pyramyd AIR within the contiguous US. Certain restrictions apply.
Free shipping may not be combined with a coupon unless stated otherwise.
View Shipping Info
During busy holidays, we step our efforts to ship all orders as fast as possible, but you may experience an additional 1-2 day delay before your order ships. This may also happen if you change your order during processing.
View Shipping Times
U.S. federal law requires that all airsoft products be sold with a 1/4-inch blaze orange muzzle or an orange flash hider to avoid being mistaken for regulated products.
View Shipping Restrictions
We can test and adjust your equipment in our Pro Shop before shipping, so you receive a product that's ready to perform right out of the box. We can even set up an optic or other equipment so you can get out shooting without the hassle. For bowhunters, our certified master bow technicians provide services such as assembly, optics zeroing, and full equipment setup, which can maximize the potential of your purchase.
By leveraging our expertise and precision, we ensure that your equipment is finely tuned to meet your specific needs and get you ready for your outdoor pursuits. So look out for our services when shopping for something new, and let our experts help you get the most from your outdoor adventures.
View Service Info
A warranty is provided by each manufacturer to ensure that your product is free of defect in both materials and workmanship.
View Warranty Details
If you need to return an item please read our return policy.
Learn About Returns
Get FREE shipping on qualifying orders! Reach your tier's spend threshold to unlock free ground shipping on items sold & shipped by Pyramyd AIR within the contiguous US. Certain restrictions apply.
Free shipping may not be combined with a coupon unless stated otherwise.
View Shipping Info
Text JOIN to 91256 and get $10 OFF Your Next $50+ Order!
* By providing your number above, you agree to receive recurring autodialed marketing text msgs (e.g. cart reminders) to the mobile number used at opt-in from Pyramyd AIR on 91256. Reply with birthday MM/DD/YYYY to verify legal age of 21+ in order to receive texts. Consent is not a condition of purchase. Msg frequency may vary. Msg & data rates may apply. Reply HELP for help and STOP to cancel. See Terms and Conditions & Privacy Policy.
Dec 21, 2012
By SP4449
Very easy to install. I have a Mendoza peep sight that I installed on an Air Venturi Bronco. It works very well.
Things I Would Have ChangedNothing.
What Others Should KnowThis is a must have for the Air Venturi Bronco with the Mendoza peep sight (which I hope will be back in production soon).