Date: 9/4/2020 23:31
0

Customers Q&A on Air Venturi Tank With Stock & Adapter, 13 cu in, Aluminum, 3,000 psi, Black

Pre-order

Out of Stock

Got a question? Got an answer?
Log in, then enter your text.

  • antonello from Italy asked:

    Salve vorrei sapere questo sistema va bene per la mia SIG Sauer MCX 4.5 c 7.5 J ?

    • Mark from USA:

      No. It is regulated to operate at 16.7 Joules. Too powerful for your Sig. No. regolamentato per operare a 16,7 Joule. Troppo potente per il tuo Sig.

  • Riel from USA asked:

    Will this work with the Hatsan barrage

    • Mark from USA:

      No. the tank is regulated for CO2 powered guns.

  • Jerry from USA asked:

    The spec sheet doesn't give dimensions of the bottle body. So what is the length of the bottle from below the valve and diameter?

    • Mark from USA:

      From below the reg/valve assembly 6 5/8" The dia is 1.5"

  • tyree from USA asked:

    Will this work on my hatsan flash.22? If so, what, if any extras do I need?

    • Mark from USA:

      No. That is a low pressure (CO2 pressure) regulated tank. It will not mate with your Hatsan Flash,nor would it work.

  • Justin from USA asked:

    Does anyone know what adapter I should use for a qb78? Im going to buy a qb79 main tube off archer airguns so it'll essentially be a 79

  • Billie from USA asked:

    what fill station adapter do i order to fill from my scuba take?

  • William from USA asked:

    Can this tank be used on the Talon P ?

    • Mark from USA:

      No

  • Evan from USA asked:

    Does this work well with a sig mpx?

    • Johnnie from USA asked:

      Is the cylinder empty when shipped?

      • Mark from USA:

        It is shipped empty.

    • Drew from USA asked:

      I own the tank with the adaptor on a Sig MCX. When I first used it, it worked fine. Now it slowly leaks air when "plugged" into the MCX. About 3000psi to <500 overnight. I don't know what the problem is. CO2 cartridges work on it but I can't detect a leak as easily being there's no guage on a disposable tank

      • Drew from USA:

        The adapter I either bought from Sig directly or from you guys. It came with some white epoxy-like glue inside. It has since disebregrated. I replaced the o-rings on the tank but when screwed in, after the adaptor, it leaks air. Does that change anything? Are there seals I need for the adaptor itself?

      • Mark from USA:

        The problem is probably with the adapter not the tank. Replace the seals/o-rings or get a new adapter.

    • Brett from USA asked:

      After using this item, I am unable to use CO2 cartridges in my Sig Sauer MPX (the CO2 cartridge will not pierce). Why is this and how do I fix it?

      • Stacey from USA:

        That would have nothing to do with the use of the air in the gun. The adapter does not touch the piercing mechanism at all. Some CO2 tanks have shorter screw ends on them and the wider body of the tank will bottom out against the back of the Sig Sauer MPX and MCX frame. Walther tanks usually work the best

    • BRETT from USA asked:

      When I installed this on my MCX I could hear the air leaking right through the rifle (slowly), but when I removed it and put a Co2 back on, no leak whatsoever....am I doing something wrong?

      • Tyler from USA:

        Hmmm, that is odd. I would suggest giving the tech department at PA a call, they can better help troubleshoot over the phone

    • David from USA asked:

      Witch hand pump can I use

      • Tyler from USA:

        Any pump with a female quick disconnect fitting on the end of the hose will work

    • David from USA asked:

      What airguns will this work on

      • Tyler from USA:

        This specific set up is for the Sig Sauer MPX and MCX

    • Don from USA asked:

      After filling this can I fill a Benjamin Armada with this Tank

      • Tyler from USA:

        No

    • Patrick from USA asked:

      How can I adjust the hammer spring tension or replace with a higher spring rate. And are there any other modifications I can do,I.e. valves,seals etc. and does anyone sell kits? I too purchased an air Venturi tank and want max FPS.

      • Tyler from USA:

        Max FPS out of what?

    • William from USA asked:

      Just got this tank and put around 500 pellets through it and the fps seems alot lower then using an 90 gram co2. Is this to be expected.

      • Tyler from USA:

        You may see a little drop off in velocity compared to warm weather performance of CO2, but you should see generally tighter velocity strings comparing the first mag to the last.

    • Randy from Canada asked:

      How many shots should I expect to get from a full tank through an MPX?

      • Tyler from USA:

        250-300

    • Carlos from USA asked:

      I would like to buy a pump to supply the tnanque. What pump can I buy to supply this tank?

    • Ozzman from USA asked:

      What adapter do I need to fill this with the Hill Mark 4 hand air pump?

    • victor from USA asked:

      if you modify the stock on a Hammerli 850 will the hpa conversion fit.

      • Tyler from USA:

        Haven't attempted it, but I have seen similarly sized bottles used in converting the 850

    • victor from USA asked:

      Is the only obstacle with this fitting on a Hammerli 850 the space. If the stock is modified will this function properly or are there any technical changes need?

      • Tyler from USA:

        That depends on what kind of performance you are looking to get. More power than the stock CO2 might require valve, plenum, hammer and hammer spring tension changes.

    • Ken from USA asked:

      Can you use this for an evanix Rex p?

      • Tyler from USA:

        No

    • Kelvin from USA asked:

      How do you refill these tanks?

      • Tyler from USA:

        You can use a high pressure hand pump or a larger capacity air cylinder. It fills via the male quick disconnect fitting at the neck of the bottle

    • johnny from USA asked:

      Can i pump air into the tank while it's connected to a gun?

      • Tyler from USA:

        Yes

    • johnny from USA asked:

      should i disconnect this from my sig mcx when im done shooting?

      • Tyler from USA:

        It can't hurt, but you don't have to. It will not cause any harm leaving it attached to the gun

    • Howard from USA asked:

      How long (or how many pumps) from an Air Venturi hand pump does it take to fill this tank to 3,000 psi?

      • Tyler from USA:

        It's about the same size as the Benjamin Marauder cylinder, right about 213 cc (Marauder is 215). You could likely fill in 5-7 minutes with a steady pace.

    • curtis from USA asked:

      Can this be filled with a benjamin hand pump?

      • Tyler from USA:

        Yes

    • David from USA asked:

      What would be needed to mate this with a fake CO2 cartridge type HPA adapter conversion (common method to convert Crosman CO2 rifles to HPA)?

      • Jonathan from New Zealand asked:

        Hello, will this work on a Hammerli 850 that curently uses 88g CO2?

        • Tyler from USA:

          No, it will not within the stock space provided because of the quick fill.

      • michael from USA asked:

        Could this be used on the Crosman QB78S with an adapter?

        • Tyler from USA:

          If you had the appropriate adapter, yes

      • chazm from USA asked:

        If you do this conversion you might also need to increase the hammer spring pressure to get the full benefit of 1100psi. Otherwise your fps might actually go down with the higher pressure because your airgun hammer cannot strike the valve hard enough at 1100 psi backpressure.

        • chazm from USA asked:

          Is the adapter sold separately?

        • Scott from USA asked:

          Can this tank be filled with my pcp hand pump?

          • Tyler from USA:

            Yes

        • Dmitry from USA asked:

          So, since it won't really increase velocity on mcx, would a tank without a regulator (which is like $60 cheaper) will bd a better fit?

          • Alex from Canada:

            No bad idea. Co2 guns are not manufacturered to take 3000psi inside the valve

        • Ross from USA asked:

          Will this work for the crosman AS2250, (king ratcatcher)?

          • Arcadian from USA asked:

            Is the regulator adjustable (2000 psi or more) ?

            • Michael from USA:

              No

          • Richard from USA asked:

            Is 1100 PSI too much for the Sig Sauer MCX

            • agustin from USA:

              The 1,800psi burst valve is to proctect the gun and user in case the regulator (1,100 output) fails. Is what the manual says. :-)

            • Michael from USA:

              88/90 gram Co2 disposable tanks should have 700psi in them when new

            • Michael from USA:

              This tank has 2 burst valves ,one set for 5000 psi and another for 1800psi . If you exceed 1800 psi the burst valve ruptures and all pressure in tank is released and it cannot be refilled or hold any pressure until a new Burst valve is installed.

            • Stanley from USA:

              No it can be filled to 3000psi per description.

          • Vegas052 from USA asked:

            Can i use this to fill my Sam Yang 909 light hunter

            • Val from USA:

              No

          • Sean from USA asked:

            Will this work with the SIG Sauer MCX CO2 Rifle

            • Tyler from USA:

              Yes

          • Sean from USA asked:

            Can I fill this with a small air compressor?

            • Tyler from USA:

              Not unless your compressor has an output capability of 3000 psi

          • richard from USA asked:

            I have the sig MCX. What will one of these tanks to the FPS on. .177?

            • Tyler from USA:

              About the same as with CO2. High 400's in my testing.

          • CNYwarlock from USA asked:

            Will this tank work on a Talon Pistol? thanks in advance.

            • Tyler from USA:

              No, it will not.

          Navigation