Will this fit the Gamo Bone Collector Bull Whisper or do I need to order the 11 mm unit?
Yes it will fit , 3/8 is the same as 11mm .
What is the saddle height of this mount?
14mm from the bottom of the mount to the bottom of the rings. 26.5mm from the bottom of the mount to the center of the rings.
Will this work on a tx200? Thanks
yes, it will
Will this work with leapers bug buster scopes?
yes, it will
I have a Daisy Model 131. Do I attached this directly to the dovetail rail or use a base that I attach to dovetail rail 1st? My 2 pc mounts just continue to walk. Is this matte finish? Thank you.
If your current mounts don't work they not be for airguns. Many people use typical 22LR mounts and that's generally a fail on a springer. These mounts hold very well, but if a gun is harder on them you have the option of adding two more rail clamp screws making it a 5-screw which won't budge, and looks better imo. Finish is matte but fairly shiny for matte so I'd say more of a gloss/matte. Whatever it is it's a great match for the bluing and scopes.
yes, you can attach it directly to the dovetail on your air rifle. It's matte finish.
Hi. Will this fir 11mm receiver dovetail rails (HW95)? Thanks
Actually it will work and it's no doubt the best option if you don't want to spend a lot more $ on one that has four clamp screws. Plus this has 5mm clamp screws, many have 4mm and thus less clamping force per screw so four 4mm screws may have less grip. With its 3-screws and the pin it's strong enough for any gun I'm aware of. I really like is the looks, it's super strong and very cheap. Since the 95 is such a nice gun I did not want to use the stop pin for fear it may mar the hole in the gun. So while I believe it will work as-is w/o the pin, and certainly will with the pin, what I did is add two more screws making it a 5-screw clamp. It's a little work but worth it imo, and it looks even better. So I'd get it and try it w/o the pin, if by chance it still slides on the rail then decide to use the pin or add two screws. Also, many mounts slide because people don't tighten the screws enough, they tighten like it's a 22LR or something and springers are substantially more more abusive. Not sure what I torque them too, I do it by feel, but it's more than the spec. Hope this helps...
in your case, no. if it was a pcp, co2, or pump action, it would work because there is not that much recoil. I do not own product, but I can tell you than for a magnum gas ram, this will not do.
will this mount work on my Nitro Venom 22?
Is there a stop pin
Is the mount body made of steel or aluminum?
Aluminum. It's a very nice unit. See the reviews, everyone is happy. It will fit a 40mm objective lens, maybe 44. If you have an objective adjustment ring it's tighter but should fit most 40AO scopes.
Is it one piece or 2. The picture is ambiguous.
One piece. It's actually 4 parts plus 12 screws, but this design is called a "one piece" as opposed to two piece version which would be pyramid # Leapers Accushot 1" Rings, Medium,.... Both types are very nice and I'd recommend them for anything.
It's a 1 piece mount
Will it work with 11mm dovetail?
Will this mount (Med.Height) work with a Benjamin Titan rifle w/Leapers 3-9x40 AO scope? Not sure if this is the best option or a dovetail to weaver/pictanny adapter with a set of Low Weaver rings. Concerned about clearance issues with a 40mm AO as well as having enough fore/aft adj. travel. Thx in advance!
Yes, you would want a medium profile mount for a 40 mm objective scope