Date: 21/5/2019 21:51
0

Customers Q&A on UTG Low-Profile Dragon Claw Clamp-on Barrel Bipod

Add to Cart

In-stock

Got a question? Got an answer?
Log in, then enter your text.

  • Neeko from USA asked:

    Allow me to refer back to Michael's inquiry if bipod needs to be removed to load breakbarrels. Stanley responded and within his reaponse had made the statement ..."Most spring or gas piston rifle aren't accurate when shooting from a bipod."... If this statement is true, outside of bringing a gun vise/lead sled, what platform should those shooting gas piston breakbarrels utilize in the field for added accuracy and stability?

    • Gavin from USA asked:

      Does this fit a crosman mtr77 np

      • Stanley from USA:

        Measure the barrel to be sure stats say 0.43 to 0.75 or almost a half an inch or 3/4 of an inch.

    • Paul from USA asked:

      So why is it called dragon claw if it can not fit the dragon claw? That is so wired.

      • Stanley from USA:

        For sure ??

    • sam from USA asked:

      can i put it on the air force texan

      • Stanley from USA:

        As long as the barrel is not larger than 3/4 of an inch.

    • Jaclyn from USA asked:

      Will this fit and work on the Gamo Whisper Silent Cat?

      • Stanley from USA:

        11mm to 19mm or just under 1/2 inch to 3/4 of an inch . Measure before you buy !

    • Ron from USA asked:

      Does this fit Benjamin Trail NPXL series with 22.5mm diameter barrel?

      • Stanley from USA:

        No only barrels to 19mm maximum .

    • Michael from USA asked:

      Won't it get in the way when you cock a spring or gas piston rifle? Do you have to remove it after every shot to cock your rifle?

      • Stanley from USA:

        Barrels need to be in the 11mm to 19mm range in order to fit , so it depends on the application.Most spring or gas piston rifle aren't accurate when shooting from a bipod. If there's enough clearance then it shouldn't have to be removed after each shot .

    • Don from USA asked:

      Will this work on a AA S510?

      • Stanley from USA:

        No it will not. Instead install a sling stud in the bottom of the stock , some of the higher end Air Arms models come with this. Then the bipod fits directly to the sling swivel stud.

    • stephen from USA asked:

      will this work on .22 airforce condor

      • Stanley from USA:

        There are better choices , the clamp on this bipod allows the rifle to rotate when sitting unattended especially if you have a large scope. It would be better to purchase a dovetail to weaver mount either from airforce or from another maker like UTG.

    • Alexander from USA asked:

      Can this UTG Low-Profile Dragon Claw Clamp-on Barrel Bipod fit on a .22 caliber air gun

      • Richelle from USA:

        It will as long as the barrel is between 11mm to 19mm.

    • Luke from USA asked:

      will this work on my crosman fury breakbarrel?

      • Stanley from USA:

        Measure your barrel if its smaller than 5/16 or 11mm it won't fit or if its larger than 3/4 of an inch or 19mm it won't fit. The specs say 11mm to 19mm. It will fit most guns.

    • Evan from USA asked:

      Will this work on the Winchester M-14 CO2 Pellet Rifle?

      • Stanley from USA:

        Measure your barrel.(SEE ABOVE)

    • Forrest from USA asked:

      Would this fit on the crosman vantage .177

      • Stanley from USA:

        Measure the barrel 11mm to 19mm or 5/16 to 3/4 of an inch smaller or bigger won't fit.

    • Jack from USA asked:

      Will this bipod fit the Benjamin Trail NP All Weather .22?

      • Stanley from USA:

        See above.

    • spider from USA asked:

      Does this fit the dual air tank dragon claw?

      • Tyler from USA:

        No. It would not be able to clamp fully around an air tube.

    Navigation