Do you know when this rifle might be available again?
This item has been discontinued. The closest model is Hatsan AT44 QES PCP Air... The long w/open sights.
The Bundles with scope do you mount and zero the scope as well?
Below all the item selections you can choose a mount scope/sight in service for $20 plus $39.99 for a hard case, A scoped rifle can only fit in a hard case to ship.
Im looking for the right scope mounts. For the ATT44 10 Long. The scope I want is the Leapers 4-16/50. My concern is the mounts that comes with that scope. Thanks in advance for your help.
My scope is an MTC Viper 50mm and uses high Hawk mounts.
What is the best pellet for hunting in this gun?
JSB "s seem to be a good starting point . In my 22 caliber Crosman hollow points seem to work very well so far.
How many pump from 0 psi all the way to max. on this gun?
Never really counted as of yet ? This has a 230cc air reservoir . Just for comparison my Airforce SS and Condor guns have a 490cc reservoir and they take between 450 and 500 pumps to fill from empty , so I'm sure these would take around 300 to 350 pumps give or take? For that reason i don't shoot mine til there empty . With the dawn of affordable compressors it could only take minutes now days
Does anyone know where I can get replacement baffles for the Hatsan AT44-10 QE Long .22 air rifle?
Give Hatsan a call or email. HatsanUSA.com
Has anyone tried the Predator Polys, H&N Hornets, 33.95 gr JSBs, or the 31 gr Newboys in the .25 cal. I know that the magazine is rather thin, however, I'm wondering if I'm going to be limited the the 25 gr JSBs.
Hi I just bought an at44 long qe and I noticed that the barrel seemed to touch the air cylinder and when i slid a piece of computer paper through the crack it proved my suspision. Will this effect my shooting?
I have the QE long in 22 caliber and mine moves too , but doesn't seem affect accuracy one bit.It seems only the shroud itself is whats moving not the actual barrel . Mine moves enough to touch the air reservoir but thats it.
Which would you consider .22 or .25, .22 for efficiency and quietness or .25 for power and knockdown
I have the QE Long in 22 caliber and i use 14.3 hollowpoint. There is such a wide range of choice available in this caliber plus you can buy them almost anywhere , that being said i have heard that the QE is very quiet all calibers thanks to the QE noise reduction system. I have the Gladius Long in 25 caliber and it puts the hurt down on whatever your shooting at ( great knockdown energy ). If your looking for knockdown bigger is always better. Maybe one day the 25 caliber will be more readily available in different weights. I like the JSB Exact Kings 25.39 grain in my 25 calibers. Good all around pellet. You can't go wrong with either caliber .My opinoin for what its worth.
Hi Do they make a tray for this rifle so you can hand load for the the poll mags and what not that won't fit in the magazine Thanks in advance
Unfortunately they don't that I've ever heard of ? You can contact hatsanusa.com and inquire and they could answer your question.
Hello once again which. 177 caliber pcp is more accurate for small game hunting....and can we decock hatsan pcp's
For small game .177 is very effective ( depending on the pellet chosen) in .177 i use crosman premier 10.5 grain dome . Have taken out rock chucks with this pellet that are bigger than a house cat . My QE long is 22 caliber and i use crosman premier 14.3 grain hollowpoints with great results. Everyone has there own opinions on what the best pellet is , you just have to experiment for yourself , this one works for me, thats all i can tell you. Yes the rifle can be decocked .
Can you use the wire brush in the barrel to clean it.. Really don't want to damage it
There are rifle cleaning kits available for a reasonable price. I wouldn't use a wire brush. Or you could search the internet for ideas , like you tube ? I started shooting mine right out of the box , and is very accurate.
What would be the heaviest pellet you would shoot out of the hatsan at44-10 qe long?? I'd like to try the 31 grain in my .25 caliber??? Not sure if it would damage it.. .
As you know the rotary mag isn't that deep so as long as it fits and doesn't stop it from turning , then it should work . I believe i read a review were someone tried a 31 grain with no problems ? Might have been a Gladius 25 ? Same mag.
Hello which hatsan pcp is lighter
The AT44-10 QE . Not the long version. Weighs in at 8.0 pounds .
Which one you recomend, hatsan 44-10 QE or benjamin marauder bote .22 pellet for dove and rabbit hunting and which scope for ea ha one
Either one would be a great choice , the m-rod would be the lighter of the two .I have the QE Long in 22 caliber and it is extremely powerful and quiet . I have read about a lot of issues with the m-rods, but in the the end its up to you? There many video reviews and articles on both ,compare and make your choice. My QE has an MTC Viper 6x24x56 side focus scope with high hawk mounts. Can be comparable to a Hawk sidewinder , i favor the Hawk scopes mostly because the controls are smoother and more precise. I know thats a lot of scope but at long distances its hard to beat. There are lighter scopes out there .Good luck.
Is the stock ambi?
Mine and other reviewers have said it comes out of box discolored , don't alarmed it cleans off with simple green.
This rifle use a barrel by Lothar Walter? Can I use a diferent gas mixture like Co2 or Nitrogen? Do you have recent facts of sales and shipment to Brazil? Thanks.
The barrels are german steel just as accurate as lothar walther . High pressure air only.
Hi guys Where does the regulator upgrade go on this rifle? Also, what will happen to the 1070fps when regulator is installed, will it drop to 800s or something? I would like to have the more accurate shots and would not mind losing some velocity, says it set at 125 bars and am not sure what that means in relation to power loss.
It goes inside the air cylinder. You will have to adjust the hammer pre-load so you will lose some velocity. Not sure what the approx. loss in velocity will be though. The reg being set at 125 BAR means that as long as you have over 125 BAR in the cylinder, the regulator will function as it should. Once you drop below that pressure, you will be "off the reg" and experience a pretty quick drop off. But up to that point, the shots will be far more consistent in terms of velocity variation from shot to shot.
can i pump this thing up from 0 psi all the way to the max with a air venturi g6 pump
Im using the hill pump no problems.
I use a benjamin hand pump, so I don't see why other hand pumps wouldn't work.
Any hand pump made for filling PCP's will do the job . So yes.
can i leave air in the gun if im done hunting u know come home and put the gun up with 2000 psi in the tank
Yes, I keep mine stored at 2900 PSI. I have read It is best to always keep some positive pressure in the gun, to keep contaminants from getting in.
I own this rifle in 22 caliber and it holds air indefinitely , doesn't leak out.
Hi, about the 44 10 qe long 22. Its rated 2 low medium but it sounds like a 22 rimfire at any pressure, shooting a 14.3 pellet. Why anybody have any idea?
Thanks paul and stan.
When you shoot lighter weight pellets, they may break the sound barrier, which causes the "rimfire" crack you hear. I use a 21 grain pellet and mine only shoots at 900 FPS, which is below the speed of sound, so much quieter. :)
I have this in 22 caliber and is an awesome rifle when you shoot it all you hear is a ping from the hammer hitting the valve . More noise is made when the pellet hits the target than anything. I use crosman premiers 14.3 hollow points and they are accurate from this rifle. When you hit something it stays down.
Does PA carry the same versions as this gun in a woodstock?
PA does not currently show any wood stock QE versions of the AT44. Only the non-QE models
What are the specs for the scope and bipod they are currently including with the rifle?
what rail system can i use on this rifle. and keep the scope low?
Depends on the scope you want to use and the rail system? I mounted a viper 6x24x56mm scope on mine with hawk two piece rings.Even for a scope this big it mounts low. I like them that way too.
Is there any way to quiet the ping made by the hammer striking the valve?
Install bottle brush half way down air tank works great check you tube
Can the air cylijder be stored while filled can the air cylinder be stored full
I have the 22 caliber and seems to hold air indefinitely . It shouldn't leak. If it does return it.
Can the air cylinder be stored while filled
Yes. There should not be a leak in the cylinder, so it should hold air. The seals should also be able to withstand the pressure for long periods of time.
can this rifle use dry nitrogen instead of hpa
No, just hpa.
Its only designed to use HPA .
What kind of o-rings should I order for replacement on the quick disconnect valve and air cylinder?
P.A. sells replacements # O-Ring Set, 0099-W Replacement for... 4.95 for 4. Also try some silicone divers grease (a thin layer) it works wonders.
can it be send to Brazil? If so,how is the total price?
You will need to check with customs in Brazil to find out if you could import it. I do not show any explicit restrictions currently. The shipping cost could be calculated by adding the item to your cart and entering your address on the shipping information page.
hatsan show this unit with thumb hole and adjustable comb. Is the image your using accurate?
Yes, this is the version we carry. I have yet to see a thumbhole/adjustable cheek version of the AT44 in the US.
Does this fill via foster fitting? I have a air force pump do i need additional fittings?
According to PCP Hookup tab here, you will need the AirVenturi Male Quick Disconnect Female adapter
Will PA carry the thumbhole stock at44 long QE soon?
No, that one has been discontinued. We now have the Hatsan Galatian QE Air Rifle which has a thumbhole stock.
do i need a special fitting to fill this? I have a foster fitting for my Maurauder and a different on for my Walter 1250 Dominator.
You will need Air Venturi Male Quick-Disconnect, 1/8"... to fill this rifle.
You can use the PCP Hookup tool (tab to the right of Questions & Answers) to determine what is needed.
Is this rifle available in the thumbhole like the hatsan web site?
Not the long version. Short version AT44-PA is available, but it's not QE series (no sound suppression at all)
Is this rifle adjustable like the Marauder?
The Marauder is totally adjustable, hammer preload, hammer throw, etc. Tha AT44 is also adjustable; you can adjust the hammer preload. It takes a chronograph and a lot of fine adjustment though.
Marauder power (FPE, FPS, shot count is not adjustable). You probably are looking at what the specs are for different calibers (and different calibers have different characteristics).
Just about everything. FPS, FPE, Shot count.
what's adjustable in Marauder?