Metal Gear Box System, High Torque Motor, Adjustable Hop-up System Gun Type: Electric Mode: Semi/Full Auto HopUp: Adjustable Caliber: 6mm Ammo Type: 0.2-0.25g Capacity: 600 rds Weight: 6.80lbs Length: 34.50" | ![]() |
![]() |
back to top |
![]() | WARNING: Battery charge time is 4.5 hours with the included charger. Do not overcharge your battery or you will damage it. (Calculate the proper amount of time required to charge a battery by dividing the battery's milliamp capacity by the chargers charge rate) The temperature can't exceed over 45 Celcius during charging or will damage the battery NOTE: The manual for the AfterMath guns states that you should charge your battery up to 11 hours. This incorrect and will result in an overcharge of the battery that may damage your gun and ruin the batteries 'memory.' |
back to top |
![]() ![]() | Warning: To prevent malfunction of the switch do not change the selector lever from semi to full auto while pulling the trigger.
1.Safety setting (the trigger cannot be pulled) When you are not firing the gun or during storage always set the selector to the safe position. |
![]() ![]() | 2. Fully automatic (automatic firing). The gun will fire automatically while the trigger remains pulled.
3. Semi automatic The gun will fire one shot each time the trigger is pulled |
back to top |
![]() Attach the protective cap to the muzzle and direct the muzzle towards safe direction(Always set the selector lever to the Safety position) | |
![]() Remove the butt plate by pressing it downwards and pull out the connector. | ![]() Insert the battery in the stock and connect connecters. |
![]() Press down the fuse box and insert connectors and cords between the fuse box and battery. Bend cords in the S shape. | ![]() When the battery and cords are set in positions, reinstall the butt plate as shown. |
back to top |
![]() Open the magazine | ![]() Insert 6mm BB bullets supplied by into the charger. (300 bullets can be inserted.) |
![]() Replace the magazine cover | ![]() Move the gear with hand clockwise until it is fully wound, and the bullets will be sent up automatcially(It can send about 150 rounds automatically) |
1. First set the front. 2. Press to the rear. 3. Press the release lever towards the trigger to lock. | ![]() Slide the rib in the arrow direction to remove remaining BB bullets. (Be careful since B bullets may jump out.) |
back to top |
![]() | The 028 series rear sight is a tangent type which is adjusted vertically according to distance to the target. Press the adjust button and slide it forward or backward to move the sight up or down. The larger the number, the longer the distance to the target. |
![]() | Insert the front sight adjustment tool in the front sight and turn it for adjustment. Counterclockwise:lower sight point Clockwise:higher sight point Caution:Be careful so as not to lose the adjustment tool. |
back to top |
![]() | The cocking lever can be moved. |
![]() | Variable hop-up adjustment lever. |
![]() | The multi protector is fixed by reverse thread as in the case of the real gun. 1. While pressing the lock button. 2. Remove by turning the multi protector. |
back to top |
![]() | |
1. Set the selector lever to Semi or Full Auto. 2. Pull the trigger. Caution:A blank firing may occur at triggering after the magazine, this is normal operation of the gun. Cautions on Motor and Battery Charge the battery if the firing cycle becomes slow.Give the air gun a rest for 5 to 10 minutes after firing about 500 rounds, in order to ensure long service lives of the motor and battery. When bullets are clogged If bullets are clogged, remove them and apply a few drops of silicone oil into the chamber from the magazine entrances shown or spray silicone oil for 0.5 to 1 sec, to obtain smooth continous Caution There are possible cases that no firing occurs after pulling the trigger in the semi-auto mode. In this case, do not pull the trigger furiously. Fire 5 to 6 shots in the full auto mode and then return to the semi auto operation. Smell may be generated from motor for a while when a new air gun is operated. This is the normal operation of the gun. The hopping up operation may be unstable for 200 to 300 rounds after using silicone oil, this is the normal operation of the gun. | |
![]() | After Operation Remove the magazine and dry fire the gun in the semi auto mode directing the muzzle to a safe direction.(Otherwise the spring may be weakened.) Set the selector to the Safe postion. Bullets may remain in the chamber even if the magazine contains no bullets(or if the magazine is not connected)(Two or three bullets may drop from the magazine, this is the normal opweator of the gun.) Always disconnect the battery and attach the protective cap whenever you do not operate the gun. Always attach the protective cap during storage |
back to top |
Symptom | Cause | Action |
No operation at all | Selector is set to safety. | Set the selector lever to Semi or Full Auto. |
Battery is not charged. | Charge the battery. | |
Battery connector is disconnected. | Connect the connector. | |
The + and - or battery connector is reverse. | Connect the connector correctly (check the fuse) | |
Fuse is blown out. | Replace the fuse. | |
Expired motor life (50,000 to 60,000 rounds) or poor electrical connection. | Replace the motor (purchasing from your dealer or check and repair the contacts) | |
Although motor is moving, no bullet jump out. | BBs are clogged in the magazine. | Insert the charging rod into the magazine and move up and down a few times to remove clogged bullets. |
BBs are clogged in the chamber. | Remove clogged bullets using the cleaning rod. | |
Faulty gear | Purchase the replacement gear from your dealer and repair. | |
Impossible full-auto operation (automatic firing) | Insufficient battery power | Charge the battery |
Faulty BBs feed of magazine | Repair clogging the magazine. | |
Impossible semi-auto operation (single shot) | Poor electrical connection | Consult your dealer for overhaul maintenance or repair. |
Deviation in gear timing | Set to semi auto after firing 5 to 6 rounds in full auto. |
Use of poor quality BB bullets will cause problems. Never diassemble or modify the gun. | ||
Symptom | Cause | Action |
Impossible semi-auto operation (single shot) | Insufficient battery power | Charge the battery |
Poor electrical connection. | Consult your dealer or us for overhaul maintenance or repair. | |
Automatic firing become shorter. | Insufficient battery power | Charge the battery |
Shooting distance become shorter | Worn or damaged chamber packing (O-ring) | Consult your dealer for overhaul maintenance or repair. Replace the chamer packing, piston assembly. |
Worn or damaged chamber packing. | ||
Deteriorated piston spring | ||
Faulty BBs (too small or too heavy) | Use genuine BBs. | |
Shortage of damaged gear | Drop a few drops of silicone oil from under the chamber. | |
Gear problem caused by too many blank firing | Consult your dealer for overhaul maintenance, part replacement (gear, etc.) or repair. | |
Too loud operating noise | Gear problem caused by too many blank firing | |
Bullets being fallen out from barrel end | Worn or damaged chamber packing | |
NO hop setting | Turn the hop adjustment lever toward HOP | |
Faulty BBs (too small) | Use genuine BBs. | |
Being wet by or dropped into water (rain) | Stop operation immediately, disconnect the battery, wipe off water from inside the main body and the battery, and, after complete dry, carry out trial firing. If no operation or malfunction is detected, consult your dealer or us for repair. | |
back to top |
By producing a back-spin to the BB bullets, this system allows for straighter and longer distance shooting than normal air gun. Unlike the fixed type, the variable hop up system permits one-touch adjustments using the dial and lever, making it an ideal hop up system. | |
![]() | Adjustment Procedure (Adjust by carry out trial firing) Gradually turn the adjustment dial towards Hop to give hop up to bullets. (The best setting is where bullets fly horizontally.) Turning excessively adversely affects the trajectory. So stop turning the hop adjustment lever when bullets fly horizontally. |
![]() | The best position is where the bullets fly horizontally, and the longest flying distance is obtained. Too much hop-up (return the lever towards NORMAL) |
![]() | Operational Caution: Strictly observe the following caution) |
If bullet clogging occurs, immediately stop firing the gun, return the hop lever to the Normal positioning and remove clogged bullets using cleaning rod. Make sure to return the hop adjustment lever to the Normal position when removing clogged bullets or cleaning. (Otherwise, the chamber packing is damaged.) Never use used or dirty bullets. (Otherwise, the chamber becomes dirty, resulting in unstable hopping up.) When about 10,000 rounds are fired, spray silicone oil into the chamber for 0.5 to 1 sec. The hopping up operation may be unstable for 200 to 300 rounds after spraying the silicone oil, this is the normal operation of the gun.) We will not be held responsible for any damage or accidents arising from wrongful operation, disassembly and modification of the gun. Any costs for repair of such damage shall be paid by the user. | |
Caution: If the hop-up is adjusted excessively causing clogging of bullets, immediately stop operating the gun. Return the lever to Normal, fire to 2 or 3 shots and readjust. Since a precision tight barrel is used, use of dirty bullets or those with burrs causes clogging of bullets and possible fatal damage to the mechanical box and system. Warning: Never hold the gun side ways the Bb bullets will curve right or left. This is due to the HOP-UP adjustment. | |
back to top |
When Hopping Up is Improper | ||
Symptom | Cause | Action |
Bullets flying upwards. | Too much hop setting | Gradually return adjustment lever towards normal |
Short flying distance of bullets (less hopping up effect) | Too much hop setting | Gradually return adjustment lever towards Normal. |
Hop packing contaminated by oil or dirt. | Fire bullets equivalent to 4 or 5 magazine or clean the chamber using cleaning rod | |
Worn or damage hop packing | Purchase the replacement part at your dealer | |
Cannot adjust | Damaged adjustment lever or other parts | Purchase the replacement part at your dealer and replace it. |
Frequent bullets clogging | Too much hop setting | Gradually return adjustment lever towards normal. |
Improper or too large sized BB bullets | Use the BB bullets for Electric Gun. | |
Dirty hop packing | Clean using the cleaning rod or consult your dealer for repair. | |
back to top |
![]() | 1. Fuse replacement procedure The fuse box comest out when the connectors are pulled out of the stock. When the fuse is replaced, push into the stock all the way. |
2. Removing Clogged Bullets (Set the Safety button to ON and remove the magazine beforehand.) | |
![]() ![]() | Insert the Cleaning road into the bore. |
Be careful so that the angled part of the Cleaning Rod faces down, and remove clogged bullets Caution: The dummy cleaning rod attached to the gun cannot be used for the clogging bullet clearing purpse. Make sure to insert the cleaning road AFTER returning the hop up lever to the Normal position. (Hop-OFF) | |
3.Maintenance when bull speed becomes low | |
![]() | |
Cut the cotton to the size shown. Adjust the length accordingly so that it can be inserted smoothly into the barrel. | |
![]() ![]() | |
Hold at the leading end of the rod and insert the rod into the barrel while turning the rod. | Caution: Inserting the rod will be difficult if you hold rod at the end. |
![]() | |
1.Apply a few drops of silicone from the bullet entrance, insert BB bullets into the magazine and fire bullets and ire bullets equivalent to 1 or 2 magazine. 2. To complete the cleaning, Use the cleaning rod (with cotton) as shown, to remove excess oil. Always carry out maintenace AFTER returning the hop up lever to the Normal position. (Hop-OFF) | |
back to top |
![]() | Remove the screw from the grip bottom. M4 hexagon wrench Insert M4 hexagon wrench into the screw hole adjust |
Hold the grip during adjustment. Otherwise, the main body will drop since the grip set screw is removed. It is recommended to lock the adjustment screw by a screw locking agent or instantaneous adhesive after adjustment of the motor position is complete. Normally, do not attempt to adjust. Be careful not to overly tighten screw as it will damage the gun. | |
back to top |
![]() |
CAUTION DISASSEMBLING (TAKING APART) THIS SOFTAIR PRODUCT VOIDS ALL WARRANTY. PRODUCT MUST BE RETURNED IN ITS ORIGINAL PACKAGING. FEDERAL LAW PROHIBITS ALTERING OR REMOVING THE ORANGE MARKING OR PAINTING OVER THE TRANSPARENT PART OF THIS PRODUCT. Do NOT use 6mm paintballs with this AEG. Shooting paintballs with this unit will result in jamming and will void warranty. Warning |
back to top |
![]() | |
![]() | |
back to top |
Get FREE shipping on qualifying orders!
Any order $150+ with a shipping address in the contiguous US
will receive the option for free ground shipping during checkout.
Certain restrictions apply.
Additionally, receive free no-hassle shipping
for orders under 10 pounds, between $120 - $149 and with a shipping address
in the contiguous US including P.O. boxes and military APO, FPO and DPO destinations.
Certain restrictions apply.
Free shipping may not be combined with a coupon unless stated otherwise.
View Shipping Info
We work hard to get all orders placed by 12 pm EST out the door within 24 hours on weekdays
because we know how excited you are to receive your order.
Weekends and holiday shipping times will vary.
During busy holidays, we step our efforts to ship all orders as fast as possible,
but you may experience an additional 1-2 day delay before your order ships.
This may also happen if you change your order during processing.
View Shipping Times
It's important to know that due to state and local laws, there are certain restrictions for various products.
It's up to you to research and comply with the laws in your state, county, and city.
If you live in a state or city where air guns are treated as firearms you may be able to take advantage of our FFL special program.
U.S. federal law requires that all airsoft guns are sold with a 1/4-inch blaze orange muzzle
or an orange flash hider to avoid the guns being mistaken for firearms.
View Shipping Restrictions
We have a team of expert technicians and a complete repair shop that are able to service a large variety of brands/models of airguns.
Additionally, we are a factory-authorized repair/warranty station for popular brands such as
Air Arms, Air Venturi, Crosman, Diana, Seneca, and Weihrauch airguns.
Our experts also offer exclusive 10-for-$10 Test and 20-for-$20 Service,
which evaluates your air gun prior to leaving our warehouse.
You'll be able to add these services as you place your order.
View Service Info
Shop and purchase with confidence knowing that all of our air guns (except airsoft) are protected
by a minimum 1-year manufacturer's warranty from the date of purchase unless otherwise noted on the product page.
A warranty is provided by each manufacturer to ensure that your product is free of defect in both materials and workmanship.
View Warranty Details
Didn't get what you wanted or have a problem? We've got you covered!
Return any item in new condition along with its original packaging and any accessories
that might have come with your air gun and receive a full product refund within 60 days of purchase
or, if you'd prefer, exchange for another product.
Our customer service team can help determine the best course of action and provide you
with some options in the event you're interested in an exchange.
Learn About Returns
Join the Pyramyd Air mailing list: Our e-mails are filled with new products, deals, sneak peeks, tips and tricks, contests and more - sign up today!
Airgun safety is no accident. You must be 18 years or older to buy any air gun or air rifle in our store.
Text JOIN to 91256 and get $10 Off Your Next $50+ Order. *Must be 18 years old. Message Frequency Varies, Text HELP for Help, STOP to Opt-Out. Message & Data Rates May Apply.