Page 6 of 6 - Quick-Disconnect Male Fitting + Reviews

Its a foster and made out of nice metal.

Make a cap that fits snug or better yet on the screws on. The on that came with fits so loose it is usless.

Noe of the O-Rings worked on my Sumatra 500. IT has a tapered fitting with a oring and the orings they provided were not thick enough to seal the fitting. I had to go and by a 3/8X1/8X1/8 O-Ring so it would work. THe dust cap they give you is useless!!!! I got a 5/16 bolt cover from manards and it fit great all I had to do was trim it tl length.

This was a simple answere to having two very different guns.

Should be shipped with a reusable protective cap.

Simple change for Korean guns. Took about 2 minutes to complete and I did not have to drain the air prior.

easy to use, no more leaking probes.

Nothing.

Sometimes refill probe's can be finicky to seal. Quick-Disconnect fittings solve
that problem.

The fitting was very easy to install. Took all of 5 minutes or less. I just unscrewed the fitting on my Sumatra 2500 carbine, removed the o-ring from it, and put it on this fitting and screwed it in and did a very slight tighten with a box wrench. Quick, easy, and it works great. No more blown o-rings on the factory probe!

Pyramid air should include the o-ring which matches the original one on the gun just in case it is damaged removing it from the factory fitting. The TWO o-rings they sent me are way to small and have NO use for this application. I have no idea what they fit.

Just do it! So much better than the factory fill probe that comes with the gun. Since installing this I have lost no air due to the factory probe o-rings blowing because of the sharp edged in the inlet hole. I lost about a quarter of tank of air when these seals would blow and I could not get it turned off fast enough. Makes it easy and painless to fill your guns.

good quality

nothing

comes with o-rings, fits my Sumatra 2500 perfectly

It took a while but, I got it to work.

Some simple instructions might be worth while. Maybe a trouble shooting guide.

I bought this to replace the fill-probe of my new Sam Yang PCP. Although I got it to work in the end, it did take some doing.

The profile of the threaded end of this item is slightly different than the threaded end of the Sam Yang Factory's threaded end. Because of this, the little "O-Ring" that is sent along with it is not sufficient to seal against leaks.

I had to run down to the hardware store to pick up a slightly larger "O-Ring" in order to keep my PCP from leaking air.

All is well now.

You can install it in seconds. Way better than the factory fittting.

nothing

This item makes my career III 707 a breeze to fill up with my benjamin pump way easier than with the factory fitting which had to be greased everytime you filled the gun (pretty messy).

Makes filling even more convenient, no more messing around with silicone grease! This allows you to make all your air rifles use a common fill fitting, which is a HUGE plus!

This was machined flat on the bottom, however the fill port on my Sumatra went into a cone shaped depression. This made the stock o-ring NOT work, and you'll have to get a thicker o-ring or washer to get an air-tight seal or it WILL leak. PYRAMID NEEDS TO ADDRESS THIS! It's an unfortunate lapse on what is a great product otherwise.

If you bought one of these and it leaks, just get a fatter o-ring for it. Also, make sure you get a filler cap to keep dirt out of it when you're hunting. This is a great way to make multiple air rifles all compatible with the same fill setup. I'd give it 5 stars if not for the o-ring situation! According to Pyramid's tech support they were able to use a .105" thickness o-ring to fix the situation and are sending me out a couple, but I couldn't wait and found one at the hardware store, works like a champ!