Page 4 of 11 - Black Ops Tactical Sniper Reviews

Excellent air rifle, very accurate and hits hard at 20 yards with 14.3 grain Premier Hollow Points. The pellets were punching through 1/4 plywood. Not sure why the stock scope gets so many bad reviews, mine was holding a tight pattern. I'm suspecting others didn't tighten it down properly.

Only thing I would have a complaint about would be the wobbly bipod, just way too much forward and backward movement. They work just not well.

Clean the barrel before you shoot it, otherwise it will be dieseling for the first 5 shots. Too much grease in the barrel from factory.

This is it. The sniper rifle used by 10K. Zombie fighter in Z NATION produced by sci fi channel. It's one hell of a gun! Nitro piston throws these .22 cal pellets 1100 FPS. and man they leave a hole. Buy one now!

I like this gun very much it shoots really hard for a break down it grouped my first 5 shoots into the size of a 50. Cent pice I also have the. 177 in this gun and I couldn't tell you which one shoots the best I would recommend this gun to anyone that enjoys shooting a lot I'm very pleased with it

The trigger set up other then that if ya could make it a little stronger but I like power and these guns have it but I'd like to see some more from it from any gun I use lol

I'm very impressed with this gun I've killed 2 wild hogs with the .177 in this looking forward in seeing what this one will do after I add a little more horse power to it thank you guys very much

Has more power than i thought it would. shots great and has a great range for what type of gun it is,

would be nice to be able to have more than one shot for loading. i get cocking gun every shot but having to load individually kinda of a pain

great gun once sighted in dead nuts accurate.

Very accurate.

Better Scope !

Definitely need a better scope for this model.

Lots of power,features galore. And it shoots straight,once you discover slugs !

More durable sound moderator, my fault maybe being too rough with the brush !

The bipod is quality, and the scews on everything need tightened. I used lower scope mounts for better accuracy and less to loosen up.Pellets need to be as heavy as possible. Enjoy !

Well made and feels rock solid. Looks great. Powerful. Definitely not a toy!

The bipod legs are flimsy and need replacing if you plan on using them. The scope needs replaced also so I gave three stars for accuracy based on the stock scope.

The super insane long and heavy trigger pull can be fixed!! They are terrible right out of the box and you do not have to live with them. You have to turn the rifle over and look through the trigger guard. There are two screws that you will need to adjust with a small flathead screwdriver. The screw in front of the trigger adjusts (shortens) the pull length and needs turned clockwise. The trick here is to pull and hold the trigger back with one hand while turning the screw clockwise with the other. There is a small hole on the trigger guard that allows you to slide the screwdriver through and access the front screw. If you tighten it too much the gun will not cock properly, so if this happens back it out half a turn. Now the screw located behind will make the trigger lighter and easier to pull. Turn this screw counter-clockwise to your personal preference. The screwdriver will need to be thin, long, and have a small flat head. This rifle is so much more enjoyable after adjusting it.

Well made and feels rock solid. Looks great. Powerful. Definitely not a toy!

The bipod legs are flimsy and need replacing if you plan on using them. The scope needs replaced also so I gave three stars for accuracy based on the stock scope.

The super insane long and heavy trigger pull can be fixed!! They are terrible right out of the box and you do not have to live with them. You have to turn the rifle over and look through the trigger guard. There are two screws that you will need to adjust with a small flathead screwdriver. The screw in front of the trigger adjusts (shortens) the pull length and needs turned clockwise. The trick here is to pull and hold the trigger back with one hand while turning the screw clockwise with the other. There is a small hole on the trigger guard that allows you to slide the screwdriver through and access the front screw. If you tighten it too much the gun will not cock properly, so if this happens back it out half a turn. Now the screw located behind will make the trigger lighter and easier to pull. Turn this screw counter-clockwise to your personal preference. The screwdriver will need to be thin, long, and have a small flat head. This rifle is so much more enjoyable after adjusting it.

I really like and enjoy this rilfe after drilling the hole to a just the triger. What a tack driver. And iam not kideing about that. Put a differnt scope on it its a barske.

I would change the scope right off the bat.

Do your self a favor and pick one up. I like the 22 cal.

Its great for the price,an Awsome plinker.

For the price absolutely nothing.

Nope.