*Some exclusions apply.
In-stock
Create an online review and share your thoughts with other customers
Sort by: | Date
| Helpfulness
| Rating
|
---|
Filer by: |
---|
5.0 5.0
3.0 3.0
very simple to use and compact
Things I would have changed:price
What others should know:a little pricey but works well and is easy to use
4.0 4.0
3.0 3.0
Gets the job done
Things I would have changed:Allow nylon end fitting to rotate and be easily replaceable
What others should know:I used a 2" hose clamp to prevent the press from walking off end of the gun.
5.0 5.0
4.0 4.0
This compressor works great. I use it on my Diana 34 with no issues. It locks tight on the scope rail and adjusts very easy. It's also very compact and can be used on a desk or table top.
Things I would have changed:Nothing.
What others should know:At first it was a bit awkward trying to get it all lined up. After a couple of uses I was using it with no hiccups. I did have to use a very small thin piece of wood the size of a matchbox car between the end of the drive screw and the spring block. No big deal though.
4.0 4.0
4.0 4.0
The dovetail attachment doesn't slip while compressing/decompressing the gun's spring. I was worried that it wouldn't hold. The compact size is very nice.
Things I would have changed:The fast release button doesn't work on mine. Air Venturi ought to just skip that and simplify the design. They'd be able to offer it at a lower price that way. The spring compressor was also a bit rusty straight out of the box. They aren't deal breakers but... I think they could have dipped the thing in packing grease and put it in a plastic bag before it left the factory. Hence my four star rating.
What others should know:I used my spring compressor to replace the spring in my Hatsan Dominator. I needed a wooden block to do the procedure. Otherwise, it was a no go. I drilled a 3/8 inch hole in the wooden block to fit over the nylon end of the screw. Then, I cut a slot on the other side of the block to fit the tapered end of the end plug on the rifle. With that wooden block, the procedure went smoothly. I didn't have to "guide" the compressor's screw at all. It stayed in place but only with that wooden block.
2.0 2.0
2.0 2.0
Small and does the job
Things I would have changed:The price is really too high, it also needs a swivel on the end of the ram as a c clamp has
What others should know:Just be careful
4.0 4.0
4.0 4.0
Convenient size and solid
Things I would have changed:It arrived with a missing set screw and the quick release button did not "pop" into place so thread engagement was questionable. I dressed the threads on the quick release and then the button popped into engagement so I felt I could trust it. I also added an additional screw near the rail end of the unit (a set screw opposing the clamping screw which squared up the clamping function) to provide a better grip on the dovetail. The original set-up was less than solid when mounted. With the additional set screw the unit mount is very solid and I was much more confident in its function. and operation.
What others should know:I was uneasy using the compressor as delivered especially as I was using it on a FWB-124 which is noted for a high spring tension. After my modifications I was convinced that the unit would perform well and it did. Once modified the unit worked very well and made the job easy and actually enjoyable.
5.0 5.0
5.0 5.0
Works great and provides a greater degree of safety compared to some of the home made compressors I have used in the past. I just used it to install and new spring and piston seal on a Beeman S1 . It worked great to hold the new spring in place while I stuck the pins in the spring plug, then I used a screw driver and an awl to "walk" the spring forward to install the pins for the trigger group, that was the tricky part, but it worked perfectly. Now my Beeman S1 shoots like brand new and can shoot through a 1" phone book like a knife through butter.
Things I would have changed:The over all design is real good, the only thing I could think of would be to provide a vertical adjustment capability to help center the threaded rod on the spring plug.
What others should know:It is worthwhile to have this tool to rebuild pellet guns
5.0 5.0
4.0 4.0
Worked very well on my RWS 34P when installing Vortek kit
3.0 3.0
2.0 2.0
The tool worked to disassemble and reassemble by air rifle.
Things I would have changed:The tool needs a bigger end. I had trouble with it walking off of the end of my action.
5.0 5.0
5.0 5.0
Small, sturdy, well made, easy to use; grips dovetail securely.
Things I would have changed:Include a handle that facilitates use.
What others should know:I easily removed the factory spring in my full power Diana/RWS 350 Magnum rifle and installed a Vortek PG2 kit with the Venturi Rail Lock Spring Compressor. Worked well on my HW85, too. This spring compressor is an essential tool for those who wish to rebuild their spring-piston guns. Your first job will pay for the compressor. Read the instructions, take your time, wear eye protection. With experience, you will learn to fabricate attachments to work in conjunction with the Air Venturi compressor.
5.0 5.0
5.0 5.0
This product is indeed all it's cracked up to be. Years ago I made my own spring compressor which worked but I always had safety concerns about it. I recently got back into airgunning and decided to rebuild my classic HW 35, and I no longer had my old compressor. I really had no need for a compressor to disassemble it, but putting a new spring in required a compressor so I ordered this. It worked great. It being clamped to the scope rails made me feel it was very safe and it was.
Things I would have changed:Well a lower price would be nice, other than that, nothing I can think of.
What others should know:I have read some questions expressing concern about why the white nylon knob does not rotate freely. On one hand it might be nice and help keep it from moving around on the receiver cap. On the other hand, I believe that the fact that it does not rotate encouraged me to go slow and carefully when compressing the spring and helped prevent me from going too fast and possibly cross-thread or "strip" the threads when mating the cap back to the receiver, so I'm good with that. Great tool for the shop and it does the job.
5.0 5.0
5.0 5.0
Simplicity. I just recently used this great tool to disassemble a Beeman R10 and a Feinwerkbau 124 sport to do a total re seal and mainspring replacement. Made the job a breeze.
Things I would have changed:There should be adapter ends, also made of Delrin, to go against the end that puts a he pressure on the rifles end cap. I say this so the pressure would be more at the center of the cap. As it sits now with its design, the end against the cap was only against the top of the cap, not in the middle, and if youre not careful it could easily pop off, sending that end cap and spring off like a bullet. Yes, adapters, made like round cups, would be perfect. Dont try a block of wood, cause when you get that end cap to the receiver tube and ready to thread on, you wont be able to spin the end cap. It has to be made of a delrin plastic to allow the cap to spin
What others should know:Great investment if you plan on working on your own springers. Because the end of therod against the end cap of your rifle wont be centered, always keep a hand on it as you tighten up the rod to make sure it doesnt pop off the end cap
5.0 5.0
5.0 5.0
I like that it works. Made it easy to tune a Hugh powered gas spring rifle. Np2 and umarex fuel.
Things I would have changed:This should come with a piccatiny rail.if you plan on using it on a dovtail buy a piccatiny rail also.
What others should know:This does not work well on a dove tail. The compressor rod doesn't line up correctly. Maybe on a magnum springer with a bigger air chamber but not on a gamo or titan.
By Geoffrey_K from USA on 2017-09-10 |
3.0 3.0
5.0 5.0
Strong unit, quality materials and simple operation. Does the job
Things I would have changed:A few things I would change are a vertical adjustment, centers fine on 25 mm tubes, larger tubes will be off center when compressing, needs an adjustment on a vertical plane. 2nd thing is the nylon tip needs to be on a bearing so it does not rotate with the shaft, as it is you will more than likely need to guide it with your fingers when it is off center on larger tubes which leads to the next problem, and I recommend you do this BEFORE USING IT!!! The beginning of the threads on both ends of the treaded shaft are razor sharp, upon first use I sliced the heck out of my finger guiding the tip on a RWS 350 large compression tube. Take a small flat file and deburr the start of the threads on both ends or buy some bandaids, your choice.
What others should know:A good tool but Air Venturi could make it better.
5.0 5.0
5.0 5.0
I just used it to put a Vortek kit in my HW50. It clamps on the scope rail. There is a quick release button on top of the threaded shaft that releases the shaft for easy and fast use.
Things I would have changed:Nothing.
5.0 5.0
4.0 4.0
Compact, easy to use, well made.
Things I would have changed:It has worked well for me-I can't think of anything that would improve the item from a functional standpoint.
What others should know:If you work on your springers, this makes life a lot easier.
By Joseph from USA on 2017-08-01 |
Buy With Confidence
Get FREE shipping on qualifying orders! Any order $150+ with a shipping address in the contiguous US will receive the option for free ground shipping on items sold & shipped by Pyramyd AIR during checkout. Certain restrictions apply.
Free shipping may not be combined with a coupon unless stated otherwise.
View Shipping Info
We work hard to get all orders placed by 12 pm EST out the door within 24 hours on weekdays
because we know how excited you are to receive your order.
Weekends and holiday shipping times will vary.
During busy holidays, we step our efforts to ship all orders as fast as possible,
but you may experience an additional 1-2 day delay before your order ships.
This may also happen if you change your order during processing.
View Shipping Times
It's important to know that due to state and local laws, there are certain restrictions for various products.
It's up to you to research and comply with the laws in your state, county, and city.
If you live in a state or city where air guns are treated as firearms you may be able to take advantage of our FFL special program.
U.S. federal law requires that all airsoft guns are sold with a 1/4-inch blaze orange muzzle
or an orange flash hider to avoid the guns being mistaken for firearms.
View Shipping Restrictions
Get the most out of your equipment when you work with the expert technicians at Pyramyd AIR. With over 25 years of combined experience, we offer a range of comprehensive in-house services tailored to kickstart your next adventure.
If you're picking up a new air gun, our team can test and tune the equipment before it leaves the warehouse. We can even set up an optic or other equipment so you can get out shooting without the hassle. For bowhunters, our certified master bow technicians provide services such as assembly, optics zeroing, and full equipment setup, which can maximize the potential of your purchase.
By leveraging our expertise and precision, we ensure that your equipment is finely tuned to meet your specific needs and get you ready for your outdoor pursuits. So look out for our services when shopping for something new, and let our experts help you get the most from your outdoor adventures.
View Service Info
Shop and purchase with confidence knowing that all of our air guns (except airsoft) are protected
by a minimum 1-year manufacturer's warranty from the date of purchase unless otherwise noted on the product page.
A warranty is provided by each manufacturer to ensure that your product is free of defect in both materials and workmanship.
View Warranty Details
Didn't get what you wanted or have a problem? We understand that sometimes things aren't right and our team is serious about resolving these issues quickly. We can often help you fix small to medium issues over the phone or email.
If you need to return an item please read our return policy.
Learn About Returns
Get FREE shipping on qualifying orders! Any order $150+ with a shipping address in the contiguous US will receive the option for free ground shipping on items sold & shipped by Pyramyd AIR during checkout. Certain restrictions apply.
Free shipping may not be combined with a coupon unless stated otherwise.
View Shipping Info
Want More?
Join Our Email List for News and Deals!
Join the Pyramyd AIR mailing list: Our e-mails are filled with new products, deals, sneak peeks, tips and tricks, contests and more - sign up today!
Text JOIN to 91256 and get $10 OFF Your Next $50+ Order!
* By providing your number above, you agree to receive recurring autodialed marketing text msgs (e.g. cart reminders) to the mobile number used at opt-in from Pyramyd AIR on 91256. Reply with birthday MM/DD/YYYY to verify legal age of 18+ in order to receive texts. Consent is not a condition of purchase. Msg frequency may vary. Msg & data rates may apply. Reply HELP for help and STOP to cancel. See Terms and Conditions & Privacy Policy.
By Tim
5.0 5.0
3.0 3.0
easy to ues and well made
Things I would have changed:pricey
What others should know:A little pricey but works fimw