Page 2 - RWS Lock Down 1-Pc Mount Reviews

This is a well made mount.

Mount grips strong and seems to hold zero.

Anti-creep pin is to far forward, will not line up with hole on barrel. RWS needs to address this issue, as I see others have had the same problem.

Solidly built unit made specifically for my RWS model 34.

In the mount specifications indicate the inside ring to ring distance and the outside ring to ring distance so the buyer can determine if the scope they intend to use will fit. This mount is long and will not work with most compact scopes.

A little Loctite 242 on the screws and check all the screws after shooting several times to keep scope on target.

Very secure mounting. Takes care of barrel drop issues. Good price.

The pin to secure as scope stop will not work on my Walther Terrus. It is not far enough back on base to use ( would interfere with safety) But the four screws to lock on dovetail work fine. Also would like to see four screws on scope rings.

All in all a very good mount set up

Super quality, great fit and finish!

Nothing

Great item

Works well and looks good. Well made.

Supply the thread lock with it.

Seems to be holding my scope well on both my RWS 34 and RWS 48. No movement so for after 100's of shots. What more could you ask for.

Works great on my hw97. Had to lower the scope because it was shooting high. A big plus for droopers

None

None

Quality, works well

Nothing right now. I'll see how I feel after 1,000, or more, shots.

I mounted the RWS Lock Down Mount on a Walther LGU that kept shooting low with a scope mated to a UTG mount without droop compensation. The RWS Lockdown mount, with its built in droop compensation, corrected the problem zeroing the scope. I can now hit field targets at 50 plus yards while staying within the operating range of the height adjustment of the Centerpoint scope mounted on my Walther. After a few hundred shots, there is no slippage. The Walther's smooth firing cycle probably helps in keeping the Centerpoint scope secure.

Good one piece mount for Large scopes Corrected my 19 inch low pellet impact at 30 yards down to 10 inches low

would have been nice to have more droop compensation to bring my pellet impact point up to bulls eye

I used this on a FWB 124 with a UTG 4-16 power X 40 mm scope and it adjusted quit nicely after I shimmed the rear of the scope up .016 which got the point of impact up to 5 inches low with a factory zeroed scope . It probably would have adjusted OK without the shims BUT I like to keep the scope adjustment minimal. Might be closer to zero on your rifle

Simple mounting, lined up perfectly on my xisco xs28m, compensated perfectly for droop

4 screws on each ring instead of 2 (used rosin and no probems )

fits chineese clones of rws models perfectly with no base movement.

Exact Fit

Nothing

Did what it was supposed to do. About 15 years ago I got an RWS 34 as a gift. Bought what was available at the local gun store as far as an airgun scope that came with two piece mounts. The scope could not be adjusted enough to get on target. I tried shimming but eventually gave up. Recently while looking on line for another scope mount for another air gun I noticed this mount. Problem solved and the RWS 34 is finally in service.

Nothing

For a break barrel springer this is what you need.

This a very solid scope mount and is clearly designed to work with RWS guns. It has not moved a bit, even with a somewhat heavy scope on it.

Nothing. It has worked perfectly.

Don't know if I really needed the droop compensation with an RWS 34, but there have been no sighting problems with it. I just works great.

I mounted a 3-9X40mm scope on a RWS Diana Model 34. The this medium height mount is holding the scope securely and has the necessary clearance without removing the rear sight. It also corrected the barrel droop problem which is common to many RWS Diana air rifles.

I would have preferred wider rings with two sets of locking screws instead of one set each.

You may need a higher set of rings if you want to mount a 50mm or greater objective scope.

made by of specifically for RWS

there are no options for change

Will not fit some scopes

Very well made. Fits perfect on my RWS 34. It won't move a bit. Droop compensation.

Use four screws in each ring for extra hold. So far, I've been tightening the rings after several shots. It's getting better...

A very good one piece mount overall.

This mount firmly grabs the grooves of any air gun. The droop compensation is vital for maximizing scope usage.

Nothing.

This piece of equipment is manufactured from aluminum. Be careful when tightening both rail screws and ring screws.Check torque guides for maximum tightening pressure for the size screws used in this product.

I bought 2 of these for my Hatsan 95 and Hatsan 125 they took care of my barrel droop problem Good product.

Not much you might say that it should work well on most springers.

Before I bought this my Hatsan 125 had so much recoil that the scope mounts would get loose after just a few shots but this adapter fixed that problem too.

Solid easy to mount, very effective for correcting barrel droop.

Maybe it cold be a little lighter

Great value

Works as it's supposed to. I had a 30mm version on my rifle before in combo with a big Hawke Sport Optics 6-24x56 AO Sidewinder 30 SF rifle scope. Has two set screws to keep it from sliding around. These fit perfectly into the recesses on my RWS Diana Magnum.

A wider ring with two more screws per end. A gun that requires locking screws also needs more ability to hang onto the scope than any other mounts do, yet it has small, one screw clamping. This would add next to zero cost. Price is already unusually high for a mount. I'm sure it's high priced because of the RWS association...

You need this if you have an RWS break barrel springer! Get a good scope that is designed to handle the significant recoil!The mount can't do it by itself!