In-stock
Create an online review and share your thoughts with other customers
5.0 5.0
5.0 5.0
By Lcloria2 from USA on 2020-03-10 16:18:43
Fits as expected for a .20 HW90 barrel, without adding a lot if weight.
Things I would have changed:Nothing.
1.0 1.0
1.0 1.0
By John from USA on 2015-07-07 19:16:44
...not much, other than the looks. I have an RWS 350 Mag in .22 and I replaced the open sights with a Leapers scope. I bought this to cover up the groves for the front sight, but my accuracy at 100 ft went from 1.5" groups to 4"
Things I would have changed:If you're going for looks, I'll admit it's sharp. However, it throws the harmonics of the barrel off, and the accuracy goes down the drain.
What others should know:Just like a tuning fork, an air gun barrel is a tuned instrument... Make it too short, and the pellet flies out too early, and the piston slams into the end of the cylinder. Make it too long, and the pellet is still in the barrel when the piston hits the end of the cylinder, and the resulting "twang" throws your accuracy right out the window. So going back to the tuning fork, the mass determines the resonant frequency. When I put the "muzzle brake" on (really a cocking handle) the added weight affected how the barrel oscillates or "whips" Cool looking cocking handle, but if you want a small tight group, go without it and live with the groves on the muzzle.
Sort by: | Date
| Helpfulness
| Rating
|
---|
Filer by: |
---|
5.0 5.0
5.0 5.0
The front is open, and it has a good finish.
Things I would have changed:Nothing
What others should know:You may need to sand or bore the Inside diameter to get it to fit properly
5.0 5.0
5.0 5.0
Fit & finish & price and the open end at muzzle !
Things I would have changed:Nothing !
What others should know:the open end at muzzle is what I prefer it give you a choice of leaving it that way and not having anything in front of your barrel crown & face which is good when cleaning you can wipe off the barrel crown when done or you could make a few baffles for a quieter backyard
3.0 3.0
1.0 1.0
Verified Purchase
It fits perfectly my Beeman R1 !
Things I would have changed:For the price I expected something else , it is only a hollow tube with 3 set screws , noting more .
What others should know:Well , it is not a moderator , that is for sure but , it give more leverage when cocking !
4.0 4.0
3.0 3.0
Verified Purchase
Looks cool, doesn't seem to change performance, 3 grub / set screws holding it on. Not gaudy, simple and seems made ok.
Things I would have changed:Give it away.give it way now... Not a deep blue finish. Good enough, but not a oh la la! super machined item
What others should know:My 34 Diana model had c fiber sights front and rear, also no Diana logo ( Goddess holding the gun) I have it all scoped out with a drooper mount so no need the stock worthless plastic sights. This covers the notch on the barrel end makes a nice grab to help cock. My vintage 24 has old school metal non fiber optic sights and is nice. I know you can buy this model with the metal sights, if your not a scooper get that one. Your mileage my vary but this thing was worth of for me. It gives the gun a nice balanced finished look.
5.0 5.0
4.0 4.0
Verified Purchase
Looks, great fits perfect on my Diana 34. maybe some blue loctite needed? . Mine has 3 grub screws in perfect length. Replaced my plastic fibre-optic sight with the plastic " glow" as big as a horses leg. Good handle for cocking. less snag out of the case. Price a tad high? but not crazy. .630 ID fit my barrel good
Things I would have changed:Just a fuzz of machining / de burring at the tapered end. Just a tad rough off the lathe Instructions on on where to place it on a barrel , i.e how much barrel crown to stick out over it? Or any help..
What others should know:I don't buy into the accuracy loss, or the sound thing. Even the the change of whip? dynamics? It fits the bill for me. Less plastic and easier to cock the barrel. I go scope as my old eyes can't see far away. I doubt your young eyes can see far away as you can drop pellets. Looks awesome. Decent price. Shipped well and fast. What more do yah want?
3.0 3.0
3.0 3.0
Well made except for machining defect near front set screw hole
Things I would have changed:Better QC, defective part should not have been shipped
What others should know:Good fit
5.0 5.0
5.0 5.0
Well made.
Things I would have changed:The need to trim the sight dovetail so much.
What others should know:Just be slow in your use of file or dremel.
5.0 5.0
5.0 5.0
Perfect fit on Diana 350
5.0 5.0
5.0 5.0
Fits as expected for a .20 HW90 barrel, without adding a lot if weight.
Things I would have changed:Nothing.
5.0 5.0
5.0 5.0
Perfect fit and looks good. Well made.
Things I would have changed:Space the grub screws closer together.
What others should know:If you want to terminate your muzzle with a modern look this one does the job.
By Scott from USA on 2018-11-03 |
5.0 5.0
5.0 5.0
Light, fit and finish.
Things I would have changed:Nothing
What others should know:Fit my Mendoza RM577 perfectly, makes a nice muzzle break for cocking do looks sweet on my rifle!
3.0 3.0
3.0 3.0
Fit & Finish
Things I would have changed:Make it a real muzzlebrake.
What others should know:This is a simple blued tapered tube that covers the unfinished portion of the barrel end. There is no sound suppression or brake action to the exhaust gas.
5.0 5.0
4.0 4.0
Fit my Diana RWS Model 34 perfectly.
Things I would have changed:An instruction sheet would be a nice addition
What others should know:No
1.0 1.0
1.0 1.0
...not much, other than the looks. I have an RWS 350 Mag in .22 and I replaced the open sights with a Leapers scope. I bought this to cover up the groves for the front sight, but my accuracy at 100 ft went from 1.5" groups to 4"
Things I would have changed:If you're going for looks, I'll admit it's sharp. However, it throws the harmonics of the barrel off, and the accuracy goes down the drain.
What others should know:Just like a tuning fork, an air gun barrel is a tuned instrument... Make it too short, and the pellet flies out too early, and the piston slams into the end of the cylinder. Make it too long, and the pellet is still in the barrel when the piston hits the end of the cylinder, and the resulting "twang" throws your accuracy right out the window. So going back to the tuning fork, the mass determines the resonant frequency. When I put the "muzzle brake" on (really a cocking handle) the added weight affected how the barrel oscillates or "whips" Cool looking cocking handle, but if you want a small tight group, go without it and live with the groves on the muzzle.
By Rony from USA on 2018-05-29 |
4.0 4.0
5.0 5.0
The muzzlebrake is a good value for the price. It makes cocking the Diana easier after removing the front sight. I am not sure if the brake has improved accuracy as the Diana was extremely accurate before installation.I installed the brake to improve appearance after removing the sights.
Things I would have changed:Maybe a fitting to encompass the crown of the barrel.
What others should know:Install with the two screws on the bottom of the barrel. File the sight ridges at the muzzle to allow the brake to slide on w/o obstruction. Blue the file marks. I used a dremel tool sander instead of a hand file.
4.0 4.0
3.0 3.0
good solid craftsmanship, lightweight yet functional, finish is nice
Things I would have changed:the price...should be $15 or less
2.0 2.0
1.0 1.0
It fit the barrel of my Xisico XS-28 .25 Cal.
Things I would have changed:It needs to be thicker, heavier and Blued, not painted.
What others should know:The walls of this muzzle break are so thin that there barely any threads for the set screws. It needs to be made thicker.
4.0 4.0
5.0 5.0
Great design (with exceptions noted below), well crafted (for the design), good material and finish. Every metal barrel break I have ever installed enhanced the accuracy and consistency of the rifle and these are no exception. I have 4 of these in operation now (2 on RWS D34s and 2 on Ruger Blackhawks) and they are doing their duty admirably.
Things I would have changed:There is a definite need for an end/muzzle cover on these for both simplicity of installation and barrel crown protection. Would also be nice if installation shims were made available for smaller diameter barrels.
What others should know:Lacking shims for some of my smaller diameter barrels, and taking a clue from previous reviews on these that complained about mounting screws loosening, I take a 1" wide strip of Gorilla duct tape 5" long and put it lengthwise dead center on the top of the barrel before installation. Slide the break on with the screws on the bottom and tighten them securely. After a couple of hundred rounds through one rifle, no noticeable loosening yet. I have used "Liquid Welder" and put an appropriate sized washer over the front of one of these, painted it Black and am testing it for robustness and longevity. Will report back if anything about this modification goes wrong or needs correction. If it stays on correctly, at least the barrel crown will continue to be protected.
By John from USA on 2014-12-06 |
By Claud from USA on 2013-05-14 |
1.0 1.0
1.0 1.0
added ballance and handle for cocking
Things I would have changed:tighter barrel sleeve and more set screws with with more substance.
What others should know:when it comes loose and it will your accuracy will be off until you resset it.
Buy With Confidence
Get FREE shipping on qualifying orders! Any order $150+ with a shipping address in the contiguous US will receive the option for free ground shipping on items sold & shipped by Pyramyd AIR during checkout. Certain restrictions apply.
Free shipping may not be combined with a coupon unless stated otherwise.
View Shipping Info
We work hard to get all orders placed by 12 pm EST out the door within 24 hours on weekdays
because we know how excited you are to receive your order.
Weekends and holiday shipping times will vary.
During busy holidays, we step our efforts to ship all orders as fast as possible,
but you may experience an additional 1-2 day delay before your order ships.
This may also happen if you change your order during processing.
View Shipping Times
It's important to know that due to state and local laws, there are certain restrictions for various products.
It's up to you to research and comply with the laws in your state, county, and city.
If you live in a state or city where air guns are treated as firearms you may be able to take advantage of our FFL special program.
U.S. federal law requires that all airsoft guns are sold with a 1/4-inch blaze orange muzzle
or an orange flash hider to avoid the guns being mistaken for firearms.
View Shipping Restrictions
Get the most out of your equipment when you work with the expert technicians at Pyramyd AIR. With over 25 years of combined experience, we offer a range of comprehensive in-house services tailored to kickstart your next adventure.
If you're picking up a new air gun, our team can test and tune the equipment before it leaves the warehouse. We can even set up an optic or other equipment so you can get out shooting without the hassle. For bowhunters, our certified master bow technicians provide services such as assembly, optics zeroing, and full equipment setup, which can maximize the potential of your purchase.
By leveraging our expertise and precision, we ensure that your equipment is finely tuned to meet your specific needs and get you ready for your outdoor pursuits. So look out for our services when shopping for something new, and let our experts help you get the most from your outdoor adventures.
View Service Info
Shop and purchase with confidence knowing that all of our air guns (except airsoft) are protected
by a minimum 1-year manufacturer's warranty from the date of purchase unless otherwise noted on the product page.
A warranty is provided by each manufacturer to ensure that your product is free of defect in both materials and workmanship.
View Warranty Details
Didn't get what you wanted or have a problem? We understand that sometimes things aren't right and our team is serious about resolving these issues quickly. We can often help you fix small to medium issues over the phone or email.
If you need to return an item please read our return policy.
Learn About Returns
Get FREE shipping on qualifying orders! Any order $150+ with a shipping address in the contiguous US will receive the option for free ground shipping on items sold & shipped by Pyramyd AIR during checkout. Certain restrictions apply.
Free shipping may not be combined with a coupon unless stated otherwise.
View Shipping Info
Want More?
Join Our Email List for News and Deals!
Join the Pyramyd AIR mailing list: Our e-mails are filled with new products, deals, sneak peeks, tips and tricks, contests and more - sign up today!
Text JOIN to 91256 and get $10 OFF Your Next $50+ Order!
* By providing your number above, you agree to receive recurring autodialed marketing text msgs (e.g. cart reminders) to the mobile number used at opt-in from Pyramyd AIR on 91256. Reply with birthday MM/DD/YYYY to verify legal age of 18+ in order to receive texts. Consent is not a condition of purchase. Msg frequency may vary. Msg & data rates may apply. Reply HELP for help and STOP to cancel. See Terms and Conditions & Privacy Policy.
By David
3.0 3.0
3.0 3.0
Verified Purchase
helps cocking effort
Things I would have changed:the finish on the product should be better