Date: 25/3/2017 4:18
0

Leapers 30mm Rings, Medium, 3/8" Dovetail

Leapers 30mm Rings, Medium, 3/8" Dovetail

Special tape inside the rings keeps your scope tight without excessive clamp pressure!

Roll over image to zoom in

Share your images

all marauder

PY-A-790

Lifetime limited warranty

$11.95

List Price $17.99 Save $6.04 (33%)

Add to Cart

In-stock

Estimate Shipping

Earn 12 Bullseye Bucks

Add to Compare
Add to Wish list

  • Description
  • Customer reviews
  • Q & A: 3 answered questions
30mm rings
Medium profile
Fits 3/8" dovetail
4 hex screws/ring secure the scope
Vertical stop pin

Special tape inside the rings keeps your scope tight without excessive clamp pressure!


In stock


Item Code: RGPM-30M4 [PY-A-790]
See manual

other products by Leapers > UTG

Create an online review and share your thoughts with other customers

5.0 5.0

5.0 5.0

By shawn from USA on 2016-12-14
See all my reviews
Was this review helpful?
0.00 ratings

Verified Purchase

Things I liked: These are the perfect height on my marauder. Seem to be good solid rings.

Things I would have changed: nothing

4.0 4.0

5.0 5.0

By kirk from USA on 2016-12-11
See all my reviews
Was this review helpful?
0.00 ratings

Verified Purchase

Things I liked: Solid build quality; they always just work with little fuss.

Things I would have changed: Can't think of anything that wouldn't increase their cost?

What others should know: Leapers/UTG are inexpensive, scope ring "Standard". No Whistles and Bells, but they just work.

5.0 5.0

5.0 5.0

By Chevota from USA on 2016-10-10
See all my reviews
Was this review helpful?
0.00 ratings

Verified Purchase

Things I liked: Outstanding mount! Looks really nice and is super strong with super clamping force on the rail.

Things I would have changed: Nothing.

What others should know: Be sure you consider the height. For example this medium is ideal for most things imo, and I much prefer the lower stance over a high mount. So far I have not needed a high for any gun, but I limit my scopes to 40AO and 44 like the UTG/Leapers with side parallax. Example; with a UTG 3-12x44AO (SCP3-U312AOIEW) I just measured and the largest part of the obj lens housing is 2.09", and the dust cap brings it to ~2.3". Mounted on a generic Crosman break barrel (Titan), with no shims, the dust cap has ~.024" clearance to the receiver. Without the cap there's .120" clearance. Something to think about if you need to shim the scope, so if needed you could sand a flat spot on the dust cap to gain room. Fyi; scopes, guns and mounts can vary with mfg changes over time etc., but at least you have some info to go on. The 1" version of these rings is ~.060" lower at scope center. Not sure why but fyi. The picture doesn't show a hole for a stop pin, but it does have one.

Show Other ReviewsCreate an online review and share your thoughts with other customers

  • Brian from USA asked:

    What is the saddle height of this ring?

    • Cory from USA:

      It is 14mm from base to bottom of ring.

  • frank from USA asked:

    will this ring accommodate a 44 mm objective lens?

    • Chevota from USA:

      With a UTG 3-12x44AO (SCP3-U312AOIEW side focus) on my generic Titan, these rings give me .024" clearance. Without the rubber dust cover I have .120", which I mention since the cover can be sanded down if needed, like if shimming the scope. That scopes bell is 2.09". Fyi.

    • Erika from U.S. Virgin Islands:

      Depends on what gun you are mounting the scope on. If it has a raised rail it shouldn't be a problem. If it is directly grooved then it will be cutting it close, a high profile may be a better choice.

  • Daniel from USA asked:

    will these fit a 11mm rail?

    • Tyler from USA:

      Yes. The Leapers/UTG mounts are made so that one side of the portion you tighten onto the rail is 3/8" and the other is 11mm.

Navigation