Date: 27/3/2017 9:27
0

Leapers Accushot 1" Rings, Medium, 3/8" Dovetail, 4 Screws/Cap

Leapers Accushot 1" Rings, Medium, 3/8" Dovetail, 4 Screws/Cap

Roll over image to zoom in

See customer imageShare your images

all marauder

PY-A-793

Lifetime limited warranty

$11.99

List Price $14.99 Save $3.00 (20%)

Add to Cart

In-stock

Estimate Shipping

Earn 12 Bullseye Bucks

Add to Compare
Add to Wish list

  • Description
  • Customer reviews
  • Q & A: 9 answered questions
  • 1" rings
  • Medium profile
  • Fits 3/8" dovetail
  • 4 hex screws/ring secure the scope
  • Vertical stop pin
Special tape inside the rings keeps your scope tight without excessive clamp pressure!


In stock


Item Code: RGPM-25M4 [PY-A-793]

other products by Leapers > UTG

Create an online review and share your thoughts with other customers

5.0 5.0

5.0 5.0

By Ron from USA on 2016-10-30
See all my reviews
Was this review helpful?
0.00 ratings

Verified Purchase

Things I liked: Very easy to set up and use.

Things I would have changed: Use counter sunk fasteners for a smoother less colthing catching setup

What others should know: Snug the fasteners only

5.0 5.0

5.0 5.0

By Chevota from USA on 2016-10-10
See all my reviews
Was this review helpful?
0.00 ratings

Verified Purchase

Things I liked: Outstanding mount! Looks really nice and is super strong with super clamping force on the rail.

Things I would have changed: Nothing.

What others should know: Be sure you consider the height. For example this medium is ideal for most things imo, and I much prefer the lower stance over a high mount. So far I have not needed a high for any gun, but I limit my scopes to 40AO and 44. Example; I have a generic 3-9x40AO Centerpoint (bundled with Crosman/Benjamin guns) that I just measured and the largest part of the obj housing is 2.1", and the cap brings it to ~2.3. Mounted on a generic Crosman break barrel (Titan), with no shims, the dust cap is tight on the receiver so it needs maybe .010" sanded off at that spot. Without the cap there's .060" clearance which is plenty for (most) shimming needs. The cap can be sanded all the way thru if needed so the same clearance would apply. Fyi; scopes, guns and mounts can vary with mfg changes over time etc., but at least you have some info to go on. If by chance you need extra super clamping force then consider the one-piece version PY-A-805 because you can drill/tap to add two more screws.

5.0 5.0

5.0 5.0

By RICHARD from USA on 2016-09-05
See all my reviews
Was this review helpful?
0.00 ratings

Verified Purchase

Things I liked: They are made very well.

Show Other ReviewsCreate an online review and share your thoughts with other customers

  • Timothy from USA asked:

    Will these rings fit a Hatsan Edge, and Centerpoint 4-16x40mmAO scope?

    • John from USA:

      These medium rings should fit a 40mm scope. Any bigger than 40mm and it's best to use high rings.

  • chuck from USA asked:

    Will these fit a gamo air rifle?

    • Chevota from USA:

      As long as it has dovetail rails, which most do.

  • Luke from USA asked:

    What is the sight height on a Marauder with these rings installed?

    • Stanley from USA:

      It depends on which scope your using 40mm , 50mm , ?

See all discussions

Consider the following similar item(s)

You may also like

Navigation