Hawke 1" Rings, Weaver, Low Reviews

Quality construction at a great price. Not fancy, they just do the job.

nothing

I used these rings to mount a 3-9x40 scope to a drooper rail on a Diana Model 34. Zeroed the scope just below the center point. I also used these mounts with a drooper rail to mount a 4-12x50 scope on my Diana 340 N-Tec.

Rings look good and are very sturdy. See to be as good as rings that cost $ more.

Used these rings to mount a Hawke Air Max 3x9 on my new Diana/RWS 48. These rings hold the scope firmly without slip using the UTG drooper base. The UTG Drooper base is needed on the Diana/RWS 48. I purchased the low rings which work fine but, I would suggest going with the medium height rings if going with the Hawke Air Max the reason for this is that the ring just (paper thin clearance) clears the rubber on the rear 40mm objective ring when mounted and adjusted for the proper eye relief.

For the RWS 48, use the medium height rings. other than that they are very good rings for the price.

Great quality rings that hold true and are way better than the price!

Overall finish is fine.

Use heavier bolts to attach rings to base.

These rings will be going back. Bolt stripped with torque setting at 25 in/lbs, package says to use up to 30. Second ring went on with no issues but you need both.

Well made and holds great. Seems to be a good strong set of rings. Looks like they will last a long time. Price is great for what you get. Would I buy them again? Yes I think so. Holds the scope well, no problems yet.

Overall these rings are serviceable, I do like the sticky padding to hold and protect the scope tube.

Stripped a base screw out on one of these. Threads are very fine and there is very little material there. I did take these on and off several times and most likely tightened them too much.

Just be careful tightening these and you will likely not have any problems.

Four hex bolts hold each ring tightly around the scope. Very solid.

Threads stripped out in hex bolt holding scope ring to the base, very undersized. Bolt diameter on my Leapers scope rings that were included with scope, are TWICE the diameter. I'll be returning these, very dissatisfied

No, I did not over torque. 1st ring was already in,. Used very little force when second one failed on me. Perhaps got a bad batch.

Perfect!

Nothing.

value for $$, they work fine

quality is not 100% BUT you get what you pay for

These Hawke rings hold very well. I mounted them on my rows 34.

Nothing.

I used these in combination with the tug leaders rail mount. Again, great advice from PA. They were a perfect match.

Very well made. Nice finish too.

Nothing.

These matched up perfectly as suggested by PA for the UTG 11mms to weaver mount as PA said they would on my RWS Diana 34. PA gives great advice.

The first set the holes on the top half didn't line up with the bottoms. I sent them back and the new one are great.

Nothing

So far the second set has been great and are holding up great.

The first set was not good the holes in the top and bottom did not line up. The second set was great so have not installed them yet.

better QC

Properly mounted in conjunction with the correct base, these will eliminate point of impact shifts on your air rifle. But be certain to use the correct base, it makes all the difference. If in doubt, contact the Pyramyd Air support team and let them help you.

Nothing

Like anything else, simply purchasing the right equipment will not hlp if it is installed incorrectly. But f you have an air rifle and are experiencing a shifting point of impact, install these rings correctly with the right base and watch your problem disappear.

like the padding inside the rings and 4 screws per ring. these centered very good on my rws 48, only moved windage 1/4 turn to get to bullseye.

nothing

good rings, would buy again.

LOCKED IN PERFECTLY ON MY RWS 48

NOTHING

GREAT RINGS AS MY SCOPE RERTAINS ZEROS

Low profile and solid hold.

Nothing

These rings were included on a previously purchased RWS34 striker combo so I bought them again for another new 34. The 4 screw/ring cap is solid as is the weaver style bolt. The scope has never shifted on my other rifle which is why I purchased these again.

Tremendous value for the quality of the item. " Rubber " liners inside the ring to prevent scope creep and cut down on the amount of pressure needed to tighten the screws.

I would not change anything with this item, except it might be nice to have a small container of blue Locktite. Just a personal thing I know.

the Allen wrench used to tighten the screws, which I tend to always lose, are metric.

These rings were what I needed to use along with a droop compensator mount for my Fury air rifle. They worked very good to hold the scope in place.

Nothing

I really didn't know what I needed until I talked to a rep at Pyramyd Air. He was very helpful and I'm happy I called and talked to a knowlegable rep rather that ordering without knowing more about what I needed. Thanks Pyramyd Air for this support. Steven