Testing the Crosman 2200 - Part 3
by B.B. Pelletier
Today, I'll look at accuracy with the 2200, and I also promised another velocity test. The gun has more shots through it now, and we wanted to see if heating or break-in was responsible for the velocity increase seen during testing last time.
I was interested in the best accuracy the rifle could offer, so I scoped it, though that really would not be my preference. With a scope on top of the receiver, the rifle is harder to pump because your other hand has to hold it at the pistol grip. That separation of hands makes you work harder to close the pump lever.
Leapers 3-9 doesn't overpower the rifle. The loading port on the side makes a one-piece mount possible.
I selected a Leapers 3-9x40 illuminated scope for this test. I selected it mostly because of the 13.5-inch length of this standard-sized scope than anything else, though I must remark that this scope has a finer reticle than many Leapers scopes. The optics are very clear, plus my lighting was nearly ideal for this test. The range was 25 yards, and 9x is close to optimum for that range.
I also discovered how to load the 2200 so that pellets never turn around. They load perfectly this way. Hold the rifle normally, instead of tipping it on its left side to see the loading port. Place the pellet on the rounded loading port side and roll it into the port. At some point the pellet will jump from your hand because you can't hold it any longer. When it does, it's in perfect alignment! Remember, hold the rifle level!
Here we go!
Two shots to sight-in and the pellets were on paper at 25 yards. I decided to stop at 8 pumps instead of 10 because the pumping was so difficult. The first shots landed low and in line with the bull, and a few clicks of elevation got me into the black.
The first 5-shot group was about one inch, but the next one went into one hole that measures 0.42 inches. The rifle seems to want to be accurate and will lob several through the same hole, then throw a couple wide. Some of the groups opened up more than I thought they should, and I guess the reason is something like the barrel crown.
Some groups looked like this one. Two shots through the center of the bull.
The best group was this one that measured 0.42" for five Premiers at 25 yards.
I tried only Crosman Premiers. I was so fixated on them for the velocity test that I guess I overlooked other good pellets such as JSB Exact 15.8-grain domes and some others. That means the accuracy might be better than I suspect from these results.
The velocity retest
This is the test that's been under my skin all along. Did the 2200 start to break in and get faster in the last velocity test, or does the gun just go faster as it warms up. I waited two hours after the accuracy testing before testing for velocity again.
The drill here was 10 pumps and shoot a Crosman Premier. I'm also showing the 10-pump string from the last test that led me to this test. Remember, we want to know if my gun is breaking-in or if it's just shooting faster because I'm warming up the pump seal with all the shooting.
The average last time on 10 pumps was 607 f.p.s. with an extreme spread of 41 f.p.s. The average this time was 612 f.p.s. with an extreme spread of 55 f.p.s.
Then, I tried pumping 2 to 10 times to see what the velocity was.
During the pumping on this test, I thought I discovered what was behind the faster shots. It had to do with how I pumped the gun. If I pumped slow and deliberate, the gun shot slower. If I rammed the pump lever closed as fast as possible the gun shot faster. Or at least that's what I thought. So, I tested the gun on 10 pumps:
Slow and deliberate
Rapid pump closure
But then I tried it again and got this:
Slow and deliberate
Rapid pump closure
The jury is still out on that one. I'd like any of you who own 2100 or 2200 rifles to try this and see what velocities you get.
This has been an interesting test. I never knew this old airgun had so much potential. And it still falls in the very affordable category. I paid $40 for mine.
One final note. I was also testing the work of airgunsmith Rick Willnecker in this report, because he resealed the rifle for me. I would say this last test demonstrates that his work can be quite good.
Rick Willnecker in PA. Visit his website, call him at 717-382-1481 or