Date: 16/1/2019 20:31
Use code: FIRST-19
*Some items excluded. Can be combined with free ground shipping on orders $150+, to contiguous US

Air Venturi Williams 64 Peep Sight

4.5100 reviews
Air Venturi Williams.

Roll over image to zoom in

See 3 customer imagesShare your images

1-year limited warranty



List Price $45.95 Save $6.00 (13%)


Out of Stock

Click to get email when it's in stock!

Estimate Shipping

Estimated in-stock date 02-05-19
Place your order now for delivery priority!

Add to Compare
Add to Wish list

  • Description
  • Customer reviews
  • Q & A: 10 answered questions

This product is out of stock.
Estimated in-stock date 02-05-2019.
Place your order now for delivery priority!

Williams Peep Sight for Benjamin Sheridan multi-pump rifles manufactured in the last 5 years. Factory-drilled and tapped for easy installation. Comes with two screws for mounting.

Item Code: AV-BJ1418 [PY-A-5]
See manual

other products by Air Venturi

Average Customer Review

4.5 (100 reviews)

Create an online review and share your thoughts with other customers

5.0 5.0

5.0 5.0

By Steve W on 2019-01-01
Was this review helpful?
0.00 ratings

Things I liked: Easy to install and set up, big difference in accuracy. Highly recommend over the factory sights if you are a little older and eyes not as good as they used to be.

Things I would have changed: Nothing - great sight that's easy to setup and use.


5.0 5.0

5.0 5.0

By George from USA on 2018-09-11
See all my reviews
Was this review helpful?
0.00 ratings

Verified Purchase

Things I liked: Perfect for the 393 and accurate. Adjustments made easy as was installation.

What others should know: Purchase with the 392 as open sights such for us more mature shooters with bifocals and progressive glasses.


5.0 5.0

4.0 4.0

By Howard from USA on 2018-06-18
See all my reviews
Was this review helpful?
5.01 rating

Verified Purchase

Things I liked: The peep sight looks great on my old Benjamin 397PA. It is much older than the 5-years recommended in the description by manufacturer. (approximately 1990 era made in Racine, Wisconsin before Crosman bought them out) It gets my groups at 10 yards as close as the optical sight I put on the gun a few years ago. With the peep sight I don't have to place my chin on the stock to get my eye in line with the scope, so I can now use the rifle with my cheek on the stock which is more comfortable and reliable for sighting in. The aperture that comes with it is .093 inches in diameter, but you can get interchangeable ones at .05 inches which will squeeze the groups even more. The packaging calls this the Williams 5D series not the Williams 64 peep sight. It is the same and does fit my Benji very well. No problems with P.O.I. being too high as others have stated, and no mod. to the sight needed. The screws that fit the holes in the side of the gun were a fraction too long, see below for fix.

Things I would have changed: 1. As stated above, the screws were two or three turns too long. That caused the screws to bind against the bolt and not allowing it to move. This was easily fixed by wrapping some small amount of washer packing below the head of the screw and screwing it back in. The screw heads did not extend beyond the body of the sight and did not interfere with the elevation mechanism, as the second screw is under it, nor bind the bolt any more; thus problem solved. This could be easily corrected by the manufacturer supplying a slightly shorter screw. 2. Possibly Pyramid Air could carry the smaller aperture as an accessory.

What others should know: The peep sight is more accurate than the manufacturer's fixed open sight. It is easier to get target acquisition than the original sight, and may aid older eyes like mine. The original rear sight on the gun must be removed, which is not a problem. Just tap the front edge of the rear sight with a hammer and block of wood knocking it rearward and it will release from the side rails and fall off. Save the side rails and rear sight for later replacement (which you probably will never want to do after using the peep sight. Zeroing in the sight does require you to loosen screws for horizontal (which I did not have to do as it was perfectly centered on the barrel when installed) and loosening one screw for elevation and turning another to raise eye piece. Once zeroed, you are good to go without changing a thing until you change distances. Others have wanted a quicker means of zeroing in, possibly if they are using gun for hunting and having to change distance often, but most of us will not.


Create an online review and share your thoughts with other customers.   Show Other Reviews

Got a question? Got an answer?
Log in, then enter your text.

  • David from USA asked:

    I wish they would make this in the notch site version.I my opinion it would work better with the front blade site on the 392 & 397.Somebody tell em we want a notch site version.Please !

    • Tyler from USA:

      Ever thought about sending Williams an email?

  • Anthony from USA asked:

    Will this sight fit on a Diana Chaser? Tony from Maryland

    • Gary from USA asked:

      how many apertures does this sight come with and what size are they?

      • Tyler from USA:

        Just the one shown

    See all discussions

    This product is out of stock. Estimated in-stock date 02-05-2019