Posts Tagged ‘semi-buckhorn rear sight’
by B.B. Pelletier
Dave Cole is this week’s winner of Pyramyd Air’s Big Shot of the Week contest on their airgun facebook page.
Nelson Lewis combination gun, made in Troy, NY, around 1850-1870. Rifle is .38 caliber; shotgun is 14 gauge.
Today, I’ll show you the results of the last two outings with this unusual combination gun. Lessons have been learned.
Before we get to today’s test report, I’d like to share a little more background on the gun’s maker, Nelson Lewis of Troy, New York.
The big match
As readers of the internet, you’re all aware that sometimes tempers flare and conversations become heated on the web. Would it surprise you to learn that this is nothing new? One hundred sixty-eight years ago there was a famous confrontation in the internet of that day — the newspaper — between Nelson Lewis and another noted gun maker, Morgan James of Utica, New York. Nelson Lewis had heard rumors that one or more of his fellow gun makers (presumably Morgan James, from the events that followed) had said he had not made the rifle he had used to beat a Mr. Williamson in a rifle match the September before. This was in the Feb. 18, 1854, edition of Spirit of the Times/A Chronicle of the Turf, Field Sports, Aquatics, Agriculture and the Stage, published in New York City. Lewis challenged whoever was spreading these rumors to put up or shut up.
Morgan James accepted the challenge, and the two men began a public correspondence in the newspaper that was not unlike what we see on the chat forums today.
Morgan James was also a famous rifle maker and a contemporary of Nelson Lewis. Like Lewis, he made long-range target rifles that were used by snipers in the Civil War. Many of James’ long-range guns were so heavy they could only be shot from a bench rest that was included as part of their equipment. He was justifiably proud of the rifles he made, as well as his own marksmanship (as was Nelson Lewis); so when he read what Lewis accused him of, he attacked with a letter of his own to the editor of the cited publication.
To make a long story short, the two men exchanged challenges in the paper, and they finally agreed to shoot five each of their rifles against each other with each maker and one or more of his friends doing the shooting. One-hundred dollars was put up for each rifle in the contest, so each maker had five hundred dollars at stake.
Morgan James and his shooters won all five matches and Lewis paid him the money (I believe); but in the end, Lewis was a sore looser. He wrote a final letter to the editor, citing the fact that Morgan James’ rifles were all heavier than his (15-18 pounds against 10-13 pounds) and of a larger caliber (.43 to .48 caliber compared to .36 to .38 caliber), plus James and his partner shot from a machine rest — but their rifles weren’t clamped down, while Lewis and his shooters all shot from common shooting benches. And Morgan James had some sort of elaborate wind gauge on the range that was operated by a separate man who reported the wind to each shooter, so he didn’t have to look at the flags. Lewis and his shooters used the common range flags that had always been used, and each shooter watched the one flag for himself.
From his report, Nelson Lewis seems to have been at a disadvantage, but why he didn’t pin down the details of the contest beforehand with so much money at stake (approximately $13,500 in 2012 purchasing power) is a mystery. He certainly should have. He claimed he thought the match was to be with hunting rifles that could reasonably be carried afield, but the small calibers he chose are a real puzzle! Morgan James did nothing wrong except to try his best to win.
So things haven’t changed, even though a century and a half has passed. Shooters still get hot under the collar and makers will do anything to defend their reputations. This is why I enjoy reading real history — because it shows that people don’t change, even though their technology does.
Enough history. Let’s go to the range.
This time, the gun was ready for the range. The loading and cleaning procedures have been worked out.
Patch problem solved
The second time I took the Nelson Lewis gun to the range, I’d solved the patch problem. Instead of the too-thick patch material I had been using the first time out, I discovered that handkerchief linen from Ireland was both the correct thickness and also was tough enough to do the job in this rifle. I cut my patches by placing a nickel over the material and cutting around it. That gives me a patch of just the right size. And when the ball is seated, I can press it into the bore with my thumb — exactly as the old masters reported a century ago.
The thinner patches fit the balls perfectly, so they can be pressed into the muzzle with the thumb as the masters of old recommend.
The proof that this material works well is seen in the patches I recovered after shooting. They are textbook examples of what a good patch should look like.
The fired patches look good. Irish handkerchief linen is strong, yet thin.
I also discovered that the powder charge could be increased a little with no detriment to accuracy. Now, the bullet gets downrange faster, which I can tell by listening to the sound of the ball striking the target at 50 yards. That may not be scientific, but it does work!
I also took the advice of Ned Roberts, who says to fill the powder measure to heaping, then wipe a straightedge across the top to level the powder. This gives a consistent amount of powder from shot to shot.
Fill the powder measure to heaping.
Then wipe a straightedge (like a knife blade) across the top of the measure to level the powder. This is called “stricken measure” in Ned Roberts’ book.
A tiny funnel Mac gave me is perfect for pouring the measured powder into the rifle barrel.
The new cleaning process
I clean the barrel after each shot. I did that the first time out, but I’ve added a few steps for a more thorough result. First, the bore is swabbed with a wet patch, followed by a brass brush, then another wet patch. These are followed by two dry patches that leave the bore sparkling clean and dry after every shot. It takes about three minutes to clean the bore this way, but that’s nothing when you’re shooting a muzzleloader.
The final thing I tried was patches lubricated both with grease and saliva. Grease is used for the patches of balls in hunting guns, where the ball will be in the barrel a long time. Saliva is supposed to give a slight edge in accuracy, but it dries out over time and also can promote rust in the bore — two good reasons why saliva is used only for target shooting.
I had high hopes that all these things would give me better groups than the first time out, but they didn’t! Something was missing.
Group fired with greased patches on June 16. Fifty yards.
Group fired with saliva-wet patches on Jun 16. Also 50 yards. No improvement.
Mac suggested that since this is a combination gun, perhaps shooting it as often as once every five minutes was letting the rifle barrel heat up enough to warp against the cold shotgun barrel. If this is a meat gun, then shouldn’t the first shot from a cold rifle be right on target? It was the best suggestion anyone had given me; so when I went to the range again this week, I did everything the same except that I waited 20-25 minutes between shots to give the gun plenty of time to cool off.
The first 4 shots went into the best group I’d seen to this point, but shot 5 went wild at 9 o’clock, ruining the group. I held as perfectly as I know how for all 5 shots, and I’ve held 5 shots in three-tenths of an inch with target sights at 50 yards this year with a .22 rimfire — so it’s not me!
Group fired with saliva-wetted patches and waiting a minimum of 20 minutes between shots. Shot at 50 yards on July 12, 2012. Four close shots, but the fifth shot opened the group to the size of the others. So this is no real improvement.
I’m now thinking that the rifling twist in this gun (remember it has a gain twist) is too fast for round balls, and that the gun wants to shoot conical bullets. A patched picket bullet is what the rifle is supposed to shoot. I’ve avoided shooting the picket bullet that came with the rifle, because making them in the manual swaging dies is a lot of hard work. But now it seems I have to try something other than round balls. We’ll see what happens next time!
Why am I doing this?
If you’re a new reader of this blog, you must be wondering if I’ve lost my mind — reporting on a 150-year-old muzzle loading firearm in an airgun blog. Here’s why I do it. Airguns don’t hold a lot of secrets from me. I’ve been around them long enough to have gotten comfortable with them and their ways. I’m not saying that I know everything there is to know, but perhaps I have become too familiar with airguns to remember all those confusing steps that baffled me when I first encountered them.
This antique firearm, on the other hand, is as foreign to me as it is to you. I’m discovering how to shoot this gun successfully and letting you watch me while I do it, so maybe you can relate to the things that stump me. This old black powder gun puts you and me on equal footing as shooters. That’s why I report on it — so you can watch me stumble around and get confused by the same things that are perhaps confusing to you.
I could just spout off a bunch of words that I read in some book and let you think I know what I’m talking about, but I prefer to do it this way. I know this approach bothers some people who wish I would just stick to airguns, but to my way of thinking, all shooting is interrelated. The more you know about all shooting subjects, the more you know about any specific subject. People who disregard black powder guns, for instance, lack a firm understanding of how pneumatics work because they’re very similar. And a poor crown will harm the accuracy of a .223 as much as it will a .177 pellet rifle.
I try to limit these reports to a minimum, but I will continue to make them from time to time because I have to. They are in me, and they have to come out.
by B.B. Pelletier
Adam Crowson is Pyramyd Air’s Big Shot of the Week.
This Nelson Lewis combination gun was made in the mid-19th century. It’s .38 caliber and 14 gauge.
A lot of readers have been waiting patiently for today’s report. Although we’re airgunners, we’re shooters first, and many of us appreciate the similarities between pneumatic guns and those that use black powder. Today’s subject gun was made about 150 years ago by a maker of some fame who made sniper rifles for use during the American Civil War. I’ve lived with this gun for several months now and have held it, admired it, considered it and wondered about it. And on Tuesday of last week, I took it to the range for its first outing.
On every TV show where old guns are shown, you’re advised to seek the services of a gunsmith before firing any old gun. They’re supposed to check the gun for safety. Last week, I discovered that I was the one performing that service on this piece.
While Mac was still visiting me several weeks ago, we pulled both locks out of the stock and examined them closely. They differ from each other only because one is for the right side and the other is for the left; but, in essence, they’re the same lock. The inletting in the stock is so precise that the left lock has to be “buttoned” into position to get it back in! It fits into an undercut section of the stock and cannot be inserted straight into its slot. A bolt passes through the left lock, through the stock and into the right lock. When tightened, it pulls both locks together in a fit so tight that a razor blade cannot be inserted between the stock and either of the two lockplates.
The locks are not complex, but they are made right and tight, which makes all the difference in the world. This is the right-hand shotgun lock.
The locks are back-action (meaning the hammer spring is located behind the tumbler, so the majority of the lock extends backward — rather than forward – from the hammer) and are remarkably simple in construction. Some file marks are still evident from the time each piece was fashioned by Lewis, who made all his own locks, triggers and barrels. For a short time, I was concerned about the gun having been “gunsmithed” because the rifle lock (operated by the rear trigger) fires with about 2 lbs. of pull and is glass-crisp. It feels too light for the gun, considering the hammer requires about 12 lbs. of effort to cock! But close examination under a 10x jeweler’s loupe shows no evidence of any work other than Lewis’ original job.
The rifle lock is on the left side of the gun, and the hammer on that side was a bit loose when I got it, so one of my gun buddies and I shimmed the square shaft on which the hammer rides with 0.0015″ shim stock. That took up all the play. Now there isn’t a hint of movement.
I removed both nipples and was pleased to see what good condition they were in. Both have tiny flash holes at their bottoms, exactly like they’re supposed to. Often, these holes will be enlarged from the hot gasses and cause greater pressure to flow back through the nipple and against the bottom of the hammer. They seem to be plated with platinum, which was a common touch on the finer guns of this period. The plating allows them to resist the erosive gasses of the gunpowder many times longer than plain steel. These are either original to the gun or are period replacements, and I would think at least the rifle nipple has to be a replacement.
Here you see the bottom of the rifle barrel nipple. It’s clearly in great condition despite its age. Notice that the breech plugs have been shaped into water drains, or “snails,” as they’re termed. They direct any water away from the nipples and also protect the barrel and lockplate from the erosive hot gasses that occur at firing. Much of the original nickel plating has been lost to these gasses.
I shined a powerful tactical flashlight down both nipple holes with the nipples removed to see down the barrels from the muzzle. Both were sparkling clean and shiny. The shotgun barrel, however, is not like any shotgun barrel of today. Instead of a mirror bore, this barrel still has tool marks, both horizontal and vertical, from when it was fashioned. You can see them in the photo of the muzzle in Part 1. I doubt there’s any choke — I can’t see evidence of one.
This photo is very revealing! Notice the graduated gap between the left and right breech plug? That’s not sloppy work, it’s intentional to provide clearance for when the plug shown right in this picture is unscrewed. Both nipples must be removed before the plugs come out. Notice the index marks that align the breech plugs with their barrels. They keep the nipples aligned with the hammers when the plugs are in place.
Then, I did some thinking about when this gun was made and what hunting was like at that time. This gun may have been made before the Civil War. Nelson Lewis made guns from 1843 into the 1880s at one location in Troy, New York. Internet research reveals that the building where he had his gun store and workshop is still standing on the corner of Congress and Church streets. Church Street is just an alley today, but Congress Street still exists, and his workshop has recently housed a small Greek sandwich shop.
It was a very different time
I can’t prove exactly when this gun was made; but as a combination gun, it’s very different from what we think of today. Let’s use the Savage model 24 for comparison. The model 24 is a modern combination gun with a rifle barrel and a shotgun barrel — just like this Lewis gun. The 24 is superposed, where this Lewis gun is side-by-side, or a Cape gun as some would call it. But Nelson Lewis also made combination guns with superposed barrels. A Savage model 24 is a lightweight, handy gun that’s useful for hunting all manner of game. The Lewis gun is also useful this way, but it’s not light!
As I reported in Part 1, it weighs 9 lbs. It’s decidedly muzzle-heavy and would not swing like a modern shotgun. But while thinking about the time period when it was used, it dawned on me that this gun may not have been designed to be used as a “handy” gun in the same terms we would think of today. It was handy because it fired both a single bullet and shot, of course, but I don’t think it was made for shooting birds on the wing.
Hunters in America didn’t always shoot birds on the wing back in 1850. They often shot them on the roost. In those days, game abounded and sportsmanship wasn’t the same as it is today. In both England and the eastern U.S., there were men in small boats called punts, and they were shooting ducks by the hundreds on the water with a small cannon called a punt gun. Nobody thought anything of a lone hunter shooting a few ducks, geese and swans while they were on the ground or the water. Yes, I said swans. Why do you think they called it “swan shot”?
“Shooting flying” is the name given to the sport of wingshooting. The flintlock made it more feasible to shoot a flying bird than anything previous; and the percussion lock, with its instantaneous ignition, coupled with the general improvement in the power of gunpowder at about the same time (1830-1840), made shooting flying gain popularity. But a meat hunter, subsistence hunter or just a plain hunter, wasn’t always interested in shooting as a sport. He was out to get food, plain and simple.
This Nelson Lewis combination gun is no more a subsistence gun than a Dodge Viper is a car for a soccer mom. Yes, it can do the job and yes, it seems to have all the necessary qualifications, but subsistence hunters can and do get along with a lot less. This is a fine sporting gun for the man who has the money to spend and wants something special. Just how special I will now discuss.
Nelson Lewis didn’t make up many guns (if any) on speculation. They were nearly all made to order, because at the price a person had to pay, which was several months’ wages for laborers, customers demanded exactly what they wanted. It’s my belief that the customer who ordered this particular gun was reasonably well-to-do, and he was also a man with very specific tastes. I believe the gun, itself, shows us that.
I’ve now seen six or seven of these Nelson Lewis combination guns in various auctions and on websites, as well as in the book by Ned Roberts, The Muzzleloading Cap Lock Rifle. They’re all similar in size, weight and caliber — with one exception. While more than half of the guns I’ve seen have the lollipop rear peep sight, mine is the only one so far that also has a hooded or globe front sight. That steel hood is there for just one purpose — to protect the thin post-and-bead “pinhead” target front sight — a sight that belongs on a target rifle.
The tiny post-and-bead front sight was meant for the most precise aiming possible with iron sights in the Nelson Lewis combination gun’s day. It seems out of place on a combination gun. Notice the beautiful condition of the rifle’s bore at the muzzle!
Remember — this is a combination gun. A gun that is both a rifle and a shotgun. It’s main purpose is for getting meat of all kinds. It’s not a target rifle, because that would have just a single barrel, double-set triggers and probably a false muzzle for more careful loading of the bullet. It’s not a shotgun, because that would be at least two pounds lighter and not muzzle-heavy. This is a meat gun — pure and simple.
So, why does it need target sights? Who puts a Lyman Super Targetspot scope on a Savage model 24? Yet, this Nelson Lewis combination gun from the mid-19th century has sights that belong on the finest target rifles of the day. Why? What about the gun requires such a precision sight, when it also has a traditional sporting rear sight mounted forward of the breech, between the barrels (see a picture of that sight in Part 1)?
These are all interesting topics to ponder, but they don’t tell us anything about how the gun really works. For that, we’ve got to get real!
When I arrived at the 50-yard range last week, all these thoughts about the gun were rambling around inside my head. Did the owner want a meat gun that was also part target rifle? And, if so, how accurate would it be?
I was about to shoot a gun that was more than a little strange. And this could be the first time it’s been fired in decades! So, as a continuance of my careful examination, the first thing I did was fire a cap on the nipple of the rifle barrel. There was a moment of panic when the caps from one manufacturer proved too small for the nipple; fortunately, the Remington No. 11 caps I had fit perfectly. I’d guessed that the No. 10 on the nipple meant the cap size, and it may well have been a size 10 of a century ago, but today a No. 11 cap fits.
After the cap fired successfully, I loaded a charge of powder into the barrel and tamped it down with a cloth wad. There was no bullet for this shot, as I was still testing the gun. That charge fired perfectly. After that, I did something I’ve never done before. I cleaned the bore with a damp cleaning patch, followed by two dry ones. According to many authors, this is the only way to do fine (accurate) shooting with black powder.
The bore was cleaned and dried after every shot. This practice was universal among target shooters in the 19th century.
Then it was time to load the first ball. For the record, I’m using fresh GOEX FFg powder. You may be wondering how I figured out the correct powder charge for this rifle. It was simple, really. I used an adjustable black powder measure and adjusted it to a little more powder than I use in my .32-caliber Thompson-Center rifle. How did I figure that powder charge? I guessed! Was I right? I seem to have been, because that rifle shot a nice tight 5-shot group at 50 yards its first time at the range.
Black powder works differently than smokeless. You don’t have to weigh each charge. You measure black powder by volumeinstead of weight, and I have enough experience with black powder guns that I won’t overload the gun. The problem may be that I load it too light, but that gets refined the more I shoot. I fill the powder measure to level full, and that’s what goes into the gun. I discovered that I do need a funnel with a really tiny mouth to fit into the muzzle, but I improvised this day with a funnel made from paper.
I used a paper funnel to drop the black powder down the bore of the rifle.
The first patch was laid over the muzzle, and a .375 swaged round ball was centered and pressed into the muzzle with my thumb. I could see this patch was going to be too large, and of course it was. When I started the ball down the barrel with the short starter, the patch closed over the top of the ball and then extended a quarter-inch above it as it was rammed down. That’s way too much patch!
The ball is pressed into the muzzle in the center of a greased patch. This patch is way too big for this ball.
The short starter is used to start the ball down the bore. At this point, the patch material had bunched up around the ball and was fighting the loading effort.
This ball was difficult to ram down until the very end of its travel, at which point I was able to feel the ball settle against the powder charge. It’s very important to always seat the ball on the powder with the same force, so this lessening of effort at the end of the ram was a providential thing. The last step in the loading process was to put a fresh percussion cap on the nipple. I then rested the gun in my rifle rest and settled in for the shot. Once I was comfortable, I pulled the hammer back to the full cock position, making the rifle ready to fire.
When ramming a ball down the bore it’s very important that you purse your lips just right!
The trigger-pull was light and glass-crisp, as noted earlier. That first shot fired with authority. The report sounded sharp, as it should when properly loaded. The recoil was very light and not bothersome to my eye that was very close to the lollipop rear peep. Fortunately, this peep folds forward for storage, so if my shooting glasses contact it during recoil it will simply lay down. I have the same setup with my Ballard rifle that recoils harder, and I always push the rear sight forward a bit with every shot.
Getting set to touch one off.
Crack! The shot is off.
I had envisioned the first shot going to the X-ring, but that’s not what happened. Instead, the shot went wide at 10 o’clock in the 7 ring. Bummer! My thought was that the oversized patch was the culprit, but only more shooting would tell me for sure. Fortunately, I had a batch of smaller size patches with me as well, so I got them out for the next loading. But before that happened, the barrel needed to be cleaned.
The hammer was pulled back to half-cock, and a damp cleaning patch was run down the bore and back out with a satisfying hydraulic pop. This was followed by two dry cleaning patches, the second of which had very little dirt on it when it came out. Then, the rifle was loaded in exactly the same way as before, with the exception that the new smaller patch was used. This time, the ball started easier and rammed easier, though even this patch was still too large for the rifle. Now, before you point out the obvious and tell me that I could have cut the patches down, let me tell you that occurred to me on the range. But I didn’t have any scissors, and a knife makes a poor patch cutter, unless you’re cutting the patch right at the muzzle. I usually do cut off my patches at the muzzle with the patch knife that I had on the range this day, but that can leave scratches on the muzzle — which I don’t mind on my Thompson-Center rifles but wouldn’t think of doing to this vintage gun!
The second shot went to the 10 o’clock position at the edge of the black, cutting the nine ring. That was more like it! I then cleaned and loaded several more times until about the fifth shot. That patch also bunched up from being too large; again, I had a hard time ramming the ball. The shot went out to 7 o’clock in the 6-ring! This demonstrates the importance of a properly patched ball.
The first shot went high and left. Then I changed patches and they started landing in the center of the target, but high. Shot five was a thin patch that got bunched-up during loading and caused unnecessary pressure to ram it down. That shot went wide to the left and low. There are two balls in the same hole at the top center of the target.
I fired a total of seven shots in all, and two of them were fliers from patches that were too tight. The other five went into a group that measures 1.903 inches between the centers of the two shots farthest apart. Two of those shots are in the same hole and have to be examined closely to see that they’re separate shots. Given the difficulties I had with the oversized patches, I think this first session went well. Of course, I’d hoped for better, but this was the first time and there was a lot to be learned.
Seven shots may not sound like a lot, but it took about 45 minutes with the loading, cleaning, picture-taking and lip-pursing. I did notice that I fell into a pattern as time went on; and by the fourth shot, I was loading them pretty much the same every time. Only that one shot (No. five with the patch that got stuck) got in the way of a perfect session.
When I returned home, I cleaned the rifle barrel by removing the barrels from the action and then removing the rifle barrel nipple. I stood the barrels in a shallow tub and poured boiling water down the muzzle of the rifled barrel. The water rushed out of the threaded nipple hole, carrying all the ash and soot with it. The boiling water left the barrels extremely hot, which made any residual water evaporate immediately. When the barrels cooled a bit (but were still very warm to the touch), I ran a clean patch with Ballistol through the bore. The outside of the breech and the nipple were both cleaned with a brass brush and assembled once the bore had been oiled. The barrel exteriors were wiped with a rag soaked in Ballistol.
Getting ready for next time
I ordered some Irish linen handkerchiefs off eBay to use as possible patch material. I thought they probably wouldn’t arrive in time, so I cut down the smallest patches I used at the range this time by holding a nickel over them and trimming around the edges with sharp scissors and lightly oiled the patches with Ballistol. They’re now roughly the same size as the two patches I found in the patch box when I got the rifle. I think the smaller amount of material will allow these patches to load more smoothly (as they are supposed to).
When the Irish linen handkerchiefs arrived, I have cut a strip of linen into nickel-sized patches that I’ve left dry (for the moment). I’ll moisten them with saliva at the range. According to Ned Roberts (of .257 Roberts fame), that gives the absolute last bit of accuracy with a patched ball. That assumes the patches are of the right thickness, and this material seems very thin. We’ll just have to wait and see. At any rate, I now have two different patches to try next time I’m out, and they’re both sized correctly for the balls I’m shooting. A saliva-moistened patch is supposed to have a slight edge in accuracy over a greased or oiled patch. Since saliva can rust the barrel, this kind of patch is used only for target practice, where the gun will be fired and cleaned within minutes. For hunting, an oiled patch is better.
I have some specific goals for next time. One is to get a better-fitting patch so the ball doesn’t have to be rammed so hard. It’s essential for accuracy to always seat the bullet on the powder charge with the same pressure every time. You can do that best when you’re pushing the ramrod down instead of ramming it. I now have patches of two different thicknesses to try, so we should see some results the next time out.
A second goal will be to weigh the powder charge I’m throwing and adjust it to what the vintage books say is the right load. Some of you may have noticed that in Part 1, I referred to the rifle as a .39 caliber, while in this report I’m calling it a .38. The ball I’m shooting is a Hornady swaged 0.375-inch round ball, and the patch does take up some space, so the caliber is just larger than .38. For that reason, I think it should more correctly be called a .38 caliber.
According to Roberts, a .38-caliber ball should use about a 35-40 grain charge, with 35 grains being closer to correct. I’ll weigh the charge I was using the last time out and adjust the powder measure to throw the “right” charge, if necessary.
Why write about firearms?
I can’t do too many of these firearms-only blogs; but since there’s so much crossover between black powder and compressed-air guns, I feel that today’s report contains several good lessons for all of us. Also, since I’m not that familiar with either this muzzleloading gun or with my Ballard, you get to watch over my shoulder as I try to learn something new. That’s useful for any new airgunner who needs to do the same kinds of things I’m doing here to learn about his new airgun.
Have you noticed that I’ve not subscribed to any forums and asked other shooters what they think about this combination gun? That’s because, in my research, I find that most people don’t know very much about guns like this, so they make stuff up or they guess. The same holds true for airguns, doesn’t it? Whenever I read a question from a new shooter about a gun he’s just bought or hopes to buy, asking me what sort of modifications I think he should do to it, I shudder. I’m saying don’t do anything at all until you have shot that gun enough to know it well. Then, you won’t be tempted to make unnecessary changes that might not be reversible. That’s the real lesson in today’s report.
And, now, for something completely different…
In 1948, the Johnson Indoor Target Gun sold for $15. That was a lot of money for an airgun in those days. What kind of powerplant did the Johnson have and what caliber was it? The answer will be in Monday’s blog, but please feel free to leave your answer in the comments.
by B.B. Pelletier
BSOTW winner Chris Moreno is shown with his first PCP.
This Nelson Lewis combination gun was made in the mid-19th century.
A little more than two years ago, I traveled to Maryland to see Mac and to help him drive back to Texas for the Malvern, Arkansas, airgun show. We visited a friend of ours who was loaning me some vintage photos to scan for articles. While there, we were admitted into his gun room, or as Mac and I refer to it — the Holy of Holies! This guy has collected odd and unusual guns all his life and, just like the Pawn Stars TV show, you never know what you’re going to find. It was there that I found the airgun pogostick repeater that Vince is attempting to make operational.
But there was another gun in his collection that intrigued me, even though I didn’t act on it right away. It was a combination gun made by Nelson Lewis, a well-known gun maker from Troy New York, who made muzzleloading guns from some time in the 1840s until at least the 1880s.
The gun came in its original oak case.
Lewis was a very prolific maker, and his guns still abound today. They’re of fine workmanship but not the absolute top tier. As far as accuracy goes, an N. Lewis gun can hold its own at 40 rods (220 yards) with all but the very finest rifles; and as far as I’m concerned, there are only three in the top rung — Schalk, Warner and Pope. Nelson Lewis belongs on the next rung down with makers like Billinghurst, Perry, Brockway and others of equal fame. His guns are never finished as fine as those of Billinghurst, but they’re equal in accuracy. They were among the first rifles selected for sniper duty in the American Civil War and made confirmed kills at ranges beyond 1,000 yards — surveyed distance.
The other kind of gun Lewis was noted for was the combination gun — with a rifle barrel on one side and a shotgun barrel on the other. That’s the gun I saw in Maryland. What intrigued me wasn’t the quality of the arm, though it’s very fine, but the condition. This gun is still in its original box after 150+ years and is in NRA Antique fine condition. The patchbox contained two round patches of thin linen material, and Lewis was known for sending a sample of the proper patching material with his guns. I can’t prove these patches are original to the gun, but they’re appropriate to it.
When it was new a gun like this cost between $50 and 60, with engraving extra if you wanted it. For that you got the gun in a wooden case, a powder measure and a bullet swage. Lewis made this gun without the use of power tools. He had a local machinist make the parts requiring a lathe, and he made the barrels, locks and triggers. His son stocked the gun in finefigured walnut.
Look at the fine joining of the shotgun and rifle barrels.
Also packed with the gun are the original dies for swaging lead picket bullets for the rifle barrel. And there were two bullets in the box along with everything else.
The swaging dies are also handmade by Lewis.
Picket bullet was the first elongated bullet that was popular. It lasted from about 1840 to 1880.
The box isn’t a presentation type box. It’s entirely functional, as though Mr. Lewis had shipped the gun yesterday and this is how it arrived. It’s designed to hold the gun when it’s broken down by removing one cross key and lifting the barreled action out of the stock. It has a patent breech with hooks that allow quick disassembly, so the gun can be transported safely to the hunting grounds.
Drift out the one key, and the barreled action can be lifted out of the patent breech. Each barrel has a separate hook that locks into the breechplate.
The ramrod appears to be original to the gun, which is quite rare for two reasons. First, this gun was probably made in the 1860s or ’70s. For anything wooden as thin as a hickory ramrod to have survived that long is remarkable. Second — a muzzleloading ramrod undergoes the most strenuous life you can imagine. Modern muzzleloaders almost always have fiberglass ramrods for this reason. Because this ramrod has lasted this long, we can surmise that this gun has been particularly well cared for.
The rifle barrel is .39 caliber and just under 28 inches long. We know that the six-grove rifling is cut with a gain twist because Nelson Lewis refused to cut any other kind of rifling. Because the picket bullet is a conical, it’s heavier than a round ball, making the rifle appropriate for deer and even black bear hunting.
The shotgun barrel is 14 gauge and is probably without a choke, as they were not popular when this gun was made. Also, a blackpowder shotgun will throw a tighter pattern just by the nature of how it functions. What we have is a cylinder bore that’s probably good out to 30-35 yards, depending on the game and shot size.
The gun has two different rear sights. On the tang is a lollipop peep sight that elevates by turning the disk on its threaded post. Halfway up the barrel is a sporting-type rear sight that can be used for a faster hunting situation. Sporting was the 19th century term for hunting.
The front sight has to be seen to be believed! The thin post is steel filed into the shape of a tiny post and bead. It’s thin but strong, because the post is an I-beam with thickness front to rear. The sight is protected by a small steel globe.
Sporting (hunting) sight is adjustable for elevation. It is a semi-buckhorn.
Folding lollipop rear target sight adjusts for elevation by turning on its stem. Windage adjusts by loosening the screw and sliding the peephole sideways.
Front sight post and bead is protected by a small globe. Entire sight can be drifted to either side to correct for windage.
The gun is 44 inches long and weighs 9 lbs. Until I received it, I had never seen it together — but it fits together tightly with a cross key and a hooked or patent breech. Once the gun is together, you can’t tell that it comes apart — it still fits that tightly.
The left barrel is the rifle barrel, and the right is the shotgun. There are no set triggers, but the rifle trigger (rear one) breaks at about 2 lbs. The rifle hammer is somewhat loose, indicating the rifle was used more than the shotgun.
Gun has a deep, crisp maker’s mark, indicating it hasn’t been refinished.
I found an oiled patch at the bottom of the shotgun barrel, which was considered the right way to store a gun in the 19th century. It had dried out and could have caused some rust if it had absorbed moisture from the air, so I removed it with the worm screw on the ramrod. The breech plugs are both removable, making both barrels accessible for cleaning. I plan to do that before long.
Both nipples appear new and would certainly have been replaced over a century and a half of use. If they were original, they would both show signs of pitting from the flame of thousands of percussion caps. One of them has the number 10 on it, so I’m guessing that’s the correct cap size.
In the patch box on the right side of the butt, I found two cloth patches that appear to be the correct size. It will take a lot of experimentation before I discover the right bullet and load for this gun, to say nothing of the shotgun side; but initially I’ll just be examining it for clues to its history!
This is an example of a fine hunting gun in very good condition from the 19th century. It shows lots of use, but the bores are clean and bright, and the action is tight and crisp, except for the hammer that was noted. It’s a wonderful window on the past that’s been preserved exactly as it was in its heyday.
Over the next few months, I’m going to get more familiar with this gun, in preparation to shooting it.
Some of you may be wondering what has become of my Ballard rifle. Well, my great idea of the special Hudson bullet didn’t turn out as well as I’d hoped. Apparently, I spec’ed the bore diameter a thousandth too large for the mold-maker, and the bullets are too difficult to push into the rifling. I have a bullet seater that’s supposed to work — and does with my smaller Lyman bullets that only go to 0.381 inches — but they don’t fill the bore all the way.
I’m going to try a couple different things to fix this. First, I’m going to shoot the rifle with loaded ammunition, using a 0.379-inch bullet so it’ll chamber and loading the cartridge with black powder to obturate the bullet. I’ll have to wipe the bore after every shot, but that was the way most shooters did it when this rifle was new.
If I get the accuracy I hope for (10 shots in a half-inch at 100 yards and 10 in two inches at 200 yards), I may invest in another hand-made Hudson bullet mold. But the rifle will really have to shine before I’m going to do that.
I’ve also found a place that will fit double-set triggers to my gun without modifying the original parts in any way. The current 7-lb. trigger-pull is one aspect that is keeping me from shooting my best.
I should have an update on shooting the Ballard sometime soon.