Benjamin Scuba Yoke, K-Valve Reviews

It works. The yoke fit on the scuba tank, the quick release coupling fit on the fill nipple, and the pressure relief valve did not leak.

The pressure gauge is difficult to make out.

It helps if you already know what needs to happen to fill and then release the pressure in the line before disconnect - because it was not clear to me from the printed directions. But with a little experimentation it became clear.

As I held this rock-solid handful of precision-made steel and brass, I saw the "Made in the U.S.A." printed on the body and said worth the extra $$$ for a quality-made tool. Very, very easy to attach to a Scuba Tank. Very quickly fills the cylinder on the gun and releasing the excess gas pressure was easy also.

I would definitely make the hose longer so as to at least allow some flexibility to attach this to the gun.

I waited a long time and spent hours using the hand pump to fill my guns which does give a great workout but which I don't always wish to do. While this costs relatively close to a hand pump, it saves so much time! I filled my gun in just a few seconds. In fact, it took me less time to fill up my gun than it normally takes for me to start filling up my gun while using the hand pump. Time is $$$. This saves a lot of time.

Easy hook up.

The gauge is not easy to read.

If you fill your own portable dive tank the pressure gauge is not accurate enough and is too hard to read accurately.

It does what it was designed for. However, this method has its draw backs.why not ship a valve that is designed specifically for the purpose of charging other sources. A unit with a pressure guage and a pressurecheck valve on the incoming side. Real simple.you charge the tank, at 3000 psi it automatically cuts off. Oh and a 24" fill hose.

Compact, easy to place on the scuba tank. Easy to read gauge. The connection to the tank fitting went on and off easily.

Add about another foot of hose.

Remember to read the instructions. Not all work the same.

Compact, easy to place on the scuba tank. Easy to read gauge. The connection to the tank fitting went on and off easily.

Add about another foot of hose.

Remember to read the instructions. Not all work the same.

EASE OF USE

LONGER CONNECTION!! VERY AWKWARD TO USE IF USING A LARGER SCUBA TANK

Does the job nicely.

After the fact I found on line for a lot less money.

Works well ,looks like very little could possibly go wrong,should last a lifetime.

5000 psi gauge could be larger, more easily read.

Short hose minimizes pressure needlessly lost.

Worth every penny not to have to use the hand pump. seconds to fill my discovery.

nothing

no

WORKS GREAT...REMEMBER FOR K' VALVES ON SCUBA TANKS..

1 METER AIR LINE...

Works as advertised, simple to use

Nuttin

Worth the money,

I like the easy operation.

The screws to lock the gauge to the tank is not strong enough when its screwed on tight.

Perhaps you should consider having the manufacturer send with two screws for tight positioning.

works as designed, great quality, nice and compact, great for the field.

a longer fill whip would have made it easier to fill the gun.

Robust construction, easy to install.Bleed screw is easy to turn.

Add about 2-3 inches to the high pressure hose. Make the guage about a half inch larger diameter.

This is the most common valve connection for scuba tanks.

I like that fact that this yoke was made to transfer air from scuba tanks to my Marauder. Made it so easy instead of using a "bicycle" pump.

The hose could be at least 36" long to transfer air a lot easier and the Gauge a litter bigger so the elderly could see better.

If you're thinking of using a scuba tank with a "Yoke" valve to transfer air to your air guns, this is an awesome piece of equipment to have.

I am very happy to be able to air up my marauder now without having to use the hand pump. It takes a lot more air to refill the reservoir on my marauder than it did my discovery, and at nearly 60 years old with a bad back, it is now a breeze to fill. The yoke fit and attached easily to the scuba tank I purchased locally, and seems to work just fine.

I do find myself wishing that the hose on the fill adapter was a bit longer, but the trade off would also be more lost air each time the line is bleed off. As you get older and require reading glasses for small print and small gauges, a larger manometer with larger dial and numbers would be a plus. I find myself having to put my readers on each time I want to charge the rifle. Not so much of an issue for young eyes.

Overall I would give this scuba yoke a good rating as it is very usable, but it could be made better esp. for older shooters, and even younger ones. How much could it cost to add a few inches to the length of the hose, and add a bigger gauge? Also just a word of thanks to Pyramyd Air for their fast shipping, and honesty in suggesting buying the scuba tank locally. Was able to buy a brand new tank at the same cost with free inspection and first air fill free. Honesty and good service keeps customers coming back.

Top of the line. Will not rust. AWESOME VALVE

NOTHING

Now that I have this item connected to a scuba tank ,I can fill my MRod .25 cal to 3000 psi. The easy way

Longer hose would be better

Price was alright . But like I said if hose was longer ,I would still pay for the extra length . Don't know WHY they made it short.

well built easy to use