Page 8 - UTG 11mm (3/8") Dovetail to Reviews

I used these to mount a massive Millett 6-25x56mm scope on my Mrod. They have held up so far over 100 shots. This is a scope that I originally bought for my .50BMG rifle, so it's a far larger/heavier scope than you would normally subject these adapters to.

Shorten the set screws so they don't stick up beyond flats of the adapters.

This part does what its intended for...Its a cheap way out..I wouldnt mount something big and heavy with it but for a small scope or red dot it works well ..Just tighten it up evenly and i never recomend using Lock tight..That stuff is for cars..

Maby make them a little stronger..

I used them on one of my Hatsans,It worked great for me..

it works pretty much like it should

better instructions The fit into the actual scope rings is not what I would have liked. The toloerances on either these bases or the scope rings (or both) could be much better. In the end, it may not matter since I have this on a P-rod and it will not really take a beating.

A lot of work to make these for such a low price.

These piece are light duty and way to delicate. You need four hands to get them in place.

Save you money and get the Hawke ones. B-Square also has the same thing. Part No. 17025 3/8" to weaver adapter

Great design, solid construction, best adapter for picatinny to weaver out there in my opinion, great price point.

Mine did not come with the allen key for the small locking screws that lock the sliders into place, not a big deal though, other then that I have no complaints.

These do not add any unnecessary bulk to your gun or weight. Great way to keep an optic low close to the barrel.

Hold great, easy to use

great simple solid conversion without adding height

nothing to change

put the smal sliding side on the side of your scope mount adusting screws and it seems to fit tighter and lower and more level

The price

No matter what I tried I couldn't get this adapter to hold. It just couldn't seat deep enough in the grove to get a solid grip and at some point during my session it would fly off. Might work in a single or multi pump pistol like the Beeman P17 or Crosman 1377 but if your gun has any kick this adapter isn't for you.

Very low profile, light, easy to install. Comes with a screw for scope stop.

The scope stop screw seem to interfere with the rings if it is not screwed down into the scope stop. I used them on a PCP and had to remove the screws.

Perfect for using Weaver/Picatinny rings on Airguns. Have not tried them on a springer so don't know if they will work as well with the springer recoil.

As advertised it converted a weaver mount onto a 11mm and 3/8" dovetail.

Nothing

Have been having a hard time finding a low 11mm and 3/8" dovetail mount. Easy to find Weaver low mounts. This did the trick!

I had my doubts but these adapters have proven themselves to be quite solid. Gives more flexibilty when trying different scopes and mounts. May save purchasing another set of rings.

Nothing I can think of.

Will raise the scope position about an eighth on a inch. That can be a benefit in some cases.

- Does what it was meant for, elevates no more than by 2 mm. - comes with a small allan key. - spring loaded so it keeps them in the scope mount for ease of installation. - Has stop pins for rifles that have recesses in the dovetail.

- The springs inside can get stuck. - it wobbles a bit on my crosman 2289 even with the clamps tightened - cannot install on the QB-70 family of rifles since their dovetails are convex.

ease of use,did not raise sight almost any very solid when tightned up

Fantastic and long overdue to the market place. Buy these and keep them handy for your AG.

nice idea ! Now I have more scope mounting choices

nothing, they worked out perfectly

Nothing

Buying this

Bought this to mount a Walther Multi Reticle Sight after about a dozen rounds the sight flew off and landed on the ground. The front window on my new sight is now cracked. I had checked before going out and after zeroing the sight. Everything seemed to be in in order, even re checked the screws for tightness. Not even worth sending back this piece of junk and I'm also out the cost of the sight.

Very easy to use and very functional with Quick detach solutions

Nothing

Nothing

Purchased this item to mount a red dot scope on my Crosman 1377 with steel breech. Easy to mount and still holding the sight solid after 100's of rounds. Can be positioned to allow easy access to the breech. Simple, effective, affordable.

Better instructions but overall installation was fairly easy.

This adapter does not tighten to the mount independently but uses the tightening mechanism from the sight to clamp to the adapter and the dovetail mount.

Small light and work well. Keeps low profile.Work well for pistols Marauder and 2240.

Nothing

You need something like these to adapt from 11 mm dove tail to weaver mounts.

not much other than they were cheap

more durable