AirForce PCP Hand Pump, 3600 PSI, w/ Hose, Adapter

Was great when it worked, but didn't last a year.

I would buy a Hill

Had this pump about 10 months. Had the internal seal on the third stage go bad: no biggie, just rebuild it, right? Well, after completing a full O-ring rebuild, the pump refuses to push air on the down stroke. It will work at times, but it is usually one in three strokes. I have taken it apart and reassembled it 6 times now and have checked everything imaginable, but it just will not pump consistently. It now takes four times the effort to pump my rifle and is keeping me from shooting. Save yourself some hassle and buy a Hill. It seems there are a lot less online complaints.

Works as advertised. Little effort by not bad.

Nothing

When using this pump be sure to use full throw of the pump.

As this is my first jump into PCPs, this pump does work well up to 3600psi for my TEXAN LSS.

As has been stated in a previous review, the 10-32 screws provided to attach the handle to pump are junk. Either a pre-fit check before shipping or a different supplier is needed.

VERY good exercise! Pumping more often is better than waiting till it is low.

If it would work.

Arrived broke. Cant get ahold of the company to replace

Good luck

It does its job

Hose too short causing it too bend quite a bit Clip that holds hose/fitting sharp and can cut your leg Screws that hold handle not adequate Poor quality control: glue on handle, lable not straight, screws came out of pressure gauge Put pressure gauge where it can be seen.

Every time I hit 2000 psi I can top off with this pump easy just 115 pumps to top off

Nothing

Perfect for hunting if you need to reload quietly

It worked.....barely. Nice hose, adapter, microfilter, and moisture trap for spare parts. Even the gauge fell apart, one I the screws holding the meter plate fell out.

Make it last, it was never smooth even when it "worked"

I bought this as a backup for top offs on my talon-ss-dor (3000#), and my HiPac'ed 2240 (1600#). I barely used it and it was never smooth, and was finicky about when it wanted to work. Then after three years it quit....sent it in to AF for rebuild and added SunOptics moisture trap. Three years later.....same. I didn't know what smooth was til I got the AV G6....NO I WOULD NOT RECOMMEND THIS TO A FRIEND.

After 6 months it would not pump past 2500psi. It seems to be leaking from the brass screw that is near the hose. Probably a o ring seal ether under the brass screw or inside the pump itself. I have not contacted airforce yet. I will update this review and rating after i see how airforce responds.

I weigh 200lbs pushing the pump down is not n issue. It would be cool if the pump was adjustable to higher pressure to decrease the number of strokes it takes to get to desired pressure.

I you use it a lot It is a pretty good core workout.

Made In Ft Worth TEXAS

Nothing

Hello,Airgunners
I had the Venturi G6 Handpump for 2 Days,it malfunctioned, so I sent back and got this one. The G6 is Made in China. AF Handpump ive had 2 weeks filled up my Coyote 5 times so far. Excellent buy

This is a very well made hand pump. But it takes a lot of pumps to fill a new tank. And toward the end a significant amount of force. I'm an older guy and at 1300 psi it bothered an old shoulder injury, and I could not continue. I had to send it back for credit against the 'Shoe Box' compressor. (An expensive upgrade.)

3000 psi compressors do not grow on trees. The Shoe Box is a well made but expensive alternative. I waited two years before buying a pre-charged air gun for this reason. I would prefer a smaller/slower and less expensive compressor.

I love the AirForce condor air gun. But the 'cost' of 3000 psi air is a big issue.