Air Venturi CO2 Bulk-Fill Adapter Reviews

It works great!!!

Nothing

You can trust pyramid air that they products will work just fine.

Good quality

price high.

Nothing on the first one. It wouldn't let air through. The second one worked like it should.

Make sure it works before it is sent out.

I bought this for my wife's MCX that was a co2. With the adapter and the air tank we have fired 100 rounds through it and the air tank has plenty of air another 100.

Low cost, solid one-piece aluminum

Quality of manufacture

What I received is different from what's advertised here. I tried using this adapter with the bottle & regulator from a .22 Gauntlet, but the adapters pin does not quite reach the regulators shutoff valve, so I didn't get any air to flow. So I bought another adapter to have a Foster QD on this Air Venturi piece, an ASA with another QD for the Gauntlet bottle, and finally had that setup working. I think it'll be better off this way, as it would've been too long. I'll just cut a hole in the MCX buttstock to run the hose out through

Perfect for the mcx

The ups delivery

I payed 4 times the because ups support is terrible

Size

Didn't add much length and can install larger C02 if you can't find local HPA fill station. Well designed.

Nothing

Price not bad.

This tiny adapter rocks my Sig-MPX O'yea!! More shots now. Many more shots now. Way more shots than i... yes!!

None. May be lower the price a bit.

Be careful with the treading. Thanks.

It's a good deal and woth the mony

What do you say?It works fine.Machining was sharp.

Nothing.

Saves u a bunch of money.88-90g tanks are about 2 for 15$ but filling up my 12 oz tank is $4.25.you do the math.

Not a damn thing

Works flawless with the EBOS

Can adapt compressed air tank to co2 guns.

Internal threads on fitting are burred, will need cleaned up before use.

Pyramyd Air fixed their suppliers mistake pronto with no questions asked! At no extra charge to me btw! Fixed part works perfectly.

It is easy to believe that when good parts come in from another source that those parts will remain at a high standard of quality. Not always the case though. 2 or 3 thousandths of an inch off can mean that all those good looking newly machined parts simply will not fit! Quality control and hands on inspection of adaptors would prevent sending out parts to customers that do not fit and have to be replaced.

First adaptor did not fit. Second adaptor did not fit. I asked them to please check the third adaptor to make sure it would fit because I did not want another bad one. They repaired some threading where the co2 tank screws on and that part worked!!! Thank you guys...thumbs up...!

I purchased it to put a large CO2 cartridge in my Hammerli 850 and it works great.

A bit on the short side for Hammerli 850.

It works and its well built not much else I can say

Nothing

Well machined with a nice finish; no rough edges or spots to nick o-rings. Has a through hole for an allen wrench or other rod to tighten it. Is long enough to seal in any 88 gram fitting. Many aren't long enough for all air guns.

Five bucks less expensive?

For my EBOS I didn't need any tape - just snug it up with a wrench through the hole.
I'd *really like* somebody to make an 88 gram to CA Mail fitting. One or two piece but compact to eliminate the length and additional o-ring (and cost) of a CA adapter.

First one went on my EBOS (which soon also gets one of Merv's FA boards)
Second will go on Blackbird as whatever adapter they send with it must be for some Russian fitting.

Easy to insert and use. Save money by using a bulk air tank, rather than the 88 gram CO2 cartridges.

Nothing

A small amount of plumber's white teflon tape put onto the threads assures no leaks.

Everything this is a basic add on that enables one to use a paintball tank for more shots and less cost than the standard 12 gram co2.

Nothing it is a good accessory that is perfected and doesn't need to be tweaked.

It's a good buy and you can get a lot shots by using it.

works great and saves you a lot of money.

You should have an on-off CO2 bottle for safe handling.

It works once its in tight.

Price is a bit high. Instructions would be nice so you don't waste a can of CO2 and risk frostbite.

Has to be tightened way way down so it doesn't leak and its soft aluminium so use the provided holes and be careful because it will deform around these tightening holes if the tool you use is too small.