Page 2 - Air Venturi Microbore Hose, DN2 Reviews

The coil protectors to prevent damaging bending are helpful. Long enough for easy use. I puchased the quick full connector, and the combination works very well, and I lose minimal air after detaching.

I would add about 6 inches of length.

Attaching the quickfill connector required no teflon tape for a good seal.

It's longer than the one I received with my MK-4 Pump.

The flexability makes this hose a pleasure to use to fill my PCP from my Air Venturi 4300/90 tank while in the field

Nothing really

I also purchased a female Female Quick Disconnect to male 1/8" BSPP fitting from Pyramid to connect the hose directly to my PCP. https://www.pyramydair.com/product/air-venturi-foster-female-quick-disconnect-to-1-8-bspp-male-5000-psi?a=4926

the strain reliefs on both ends

add a washer to the end that goes into the pump

I replaced the standard hose that came on my Hill mk4 pump with this microbore hose. I noticed that the pressure dropped on the pumps gauge between strokes and it as taking a lot of work to raise the pressure on my Marauder. I looked at the standard Hill hose and saw a metal washer with a rubber insert. When I installed it on my microbore hose the leak stopped and the pressure in the gun went up faster.

You will save your self about 2-4 pump stroke each time you pressurize your pump for filling. These hoses have less volume so it takes less strokes to fill them or you waste less air from your scuba tank.

Nothing

Replace your existing hose with this one or get two and make your hose longer. I have three of these two are connected together and I can pump my gun in any location because of the long length.

Less pumping.

Offer it in longer lengths.

It takes 1/2 as many pumps to fill the hose.

Length, Flexibility, Durability.

Make a version with Foster quick disconnect fitting as standard.

Hose length seems adequate to me. The with the small hose you don't waste a lot of air when charging your gun.

I wish it was offered with a male foster fitting on one end and a female foster fitting on the other.

I ordered this hose along with the two fittings I needed (PY-A-3550 & Air Venturi Microbore Hose, DN2,...) to make an extension for my Discovery pump or to use with my scuba tank which has a female foster fitting.

It extends the length and gives you more leeway so you don't have to have your gun in an awkward position.

Nothing" It works as it should it is a basic product that eases the filling of your gun.

If you buy it,You will say,Why didn't I get one before?

I was able to adapt this hose to my Ninja 90ci PCP tank. I helps to conserve air over the stainless braided line, that came with the Ninja setup.

Offer a hose with two male ends, instead of one female and one male end.

length of hose

none

Like the product just fine

well made.

it needs to be longer, 3 feet.

This is a high quality product. - well made. I recommend this hose for adding to the Hill Pump.

If this hose came in 4 - 6 foot lengths it would enable the shooter to set the gun on a shooting bench, tailgate, etc for better re-filling convenience.

I added this hose directly to the existing hose on my Hill Pump to give me more length so the gun doesn't have to be so close to the ground when re-filling.

These hoses hopefully become the "new standard" as they save a lot of air. I used this hose to extend the hose I already had and makes my guns much easier to fill.

The hose works great, I just wish they could be bought in several different lengths as this would save everyone money that needs longer hoses.

High quality hose and saves air!

works as intended, no leaks, no thread seal needed, like the spring coil at each end to prevent kinking

make a longer one, 4ft, lower cost

It's a well made product. The strain relief prevents kinking and the small internal diameter doesn't waste much air.

Nothing

Make sure you get fittings for the BSPP threads.

Replaced the standard hose on the Hill pump with this, it allows me to recharge my Marauders while sitting in a gun vise and not laying on the floor.

Nothing

It is a direct replacement for the hose on the Hill MK3 pump.

Better than my stock hose and a little pricey, but the quality is good.

Include the quick- disconnect.

I bought this and the Air Venturi Female Quick-Disconnect Adapter to go on a used hill pump I picked up. The microbore hose is nice and takes less pumps than the stock hose.

Durable, well made

Use NPT ends ...that's all just say'n We aren't Britts,

BSPP is not NPT.. get the adapters and you'll be alright

Easy to use, fits well with fittings on air rifle.

Seems like small diameter flexible tubing may be too weak to hold up to high pressure. I had the hose "blow out" on my first fill.