Crosman Pellet Loader, Holds 16 Reviews

Absolutely useless I wish I could get my money back

Metal tube

Plastic vinyl tubing end cap

The sleazy little piece of clear vinyl tubing end cap is pretty useless.

It is:
- somewhat difficult to get on the end of the metal tube;
- captures one or two pellets which then both: hinder putting the vinyl tubing section back on the holder, and are difficult to get out of it without possibly deforming them,
- doesn't help the process any more than preventing the remaining pellets in the tube from falling out.

It would be much more helpful to have:

- a custom cap that would fit over the end of the tube;
- perhaps with a provision (hole or indentation) on the end that could hold one pellet by the skirt ready to grab and load;
- a keeper strap to prevent it from being dropped and lost.

The little clear vinyl tubing section for mine at the moment is lost as I set it in my lap as I write this ( I'm glad I'm not out in the grass and brush... )

Note: the pellets pour freely from the far end of the tube - it's easy to inadvertently dump too many out.

I have (3) of these that I use with my Crosman Varminator break-barrel, and the work out great. Mostly metal construction, so they offer greater durability than the all plastic ones that are out there. Even though it does not have "clicks" (eye-roll) it is very easy to use one handed. Yes, it may hold (16) pellets, but don't fight the long reach with your thumb, and try loading only (10), works that way with no problem.

Nothing, IMHO, works great as designed.

As I mentioned above, loading only 10 or 12 pellets make it easier to reach with your thumb and is very positive and easy to load one-handed.

It does help to load pellets better. Is very useful in handling the Crosman 1377 steel breech issue of the screw not being perfectly flush underneath the chamber. It is also very useful when loading the Beeman P17 which has a very awkward loading method without this loader. It would also help in a scenario where you wanted to fire in rapid sequence as you wouldn't have to fumble with the pellets from the pouch, but could just squeeze them out of this device.

I think it's a little over priced, as it's very simple, but cost more than a picatinny adapter.

It wouldn't be necessary if the steel breech kit or the P17 were engineered a little better.

Loads easy.Makes loading pistols and magazine easy.

Nothing

Plunger may need smoothed with sandpaper or pocketknife.

Great tool and easy to use.

Nothing!

used it only one time and was not to impressed

Loads my pellets

Not much, maybe a better stop so it's easier to just push one pellet at a time.

When you will, it, the red push stick hangs out the top a little awkward. Good for at home plinking, not sure how practical it is to use for outdoor shooting away from home.

Nothing

Should never purchased such a cheap item, is not worth 2 cents

It is easy to load. When your loading the rifle you are not fumbling with the pellets.

None

Be safe; air guns can hurt you.

Pellet Pen is better

Pellet Pen is best

Get the Pellet Pen
It's worth the money

nothing

make it work

the design is fundamentally flawed. it does not work. who approved this for production?

Solid construction

The design is flawed. When it is full, the plunger or push stick is way too long so you cannot really carry it since it sticks way out. Also has not way on controlling how many pellets are pushed through.

Go with the Pellet Pens which are much better products

Keeps Several pellets available

Construction and design

This is flimsy and only properly centers the pellet about half the time and then it very rarely seats the pellet to the necessary depth. I would not recommend to those who want anything more than a pellet keeper. This simply falls short when used to attempt loading and seating. I am very disappointed. This report is from use with a brand new clean Crossman rifle and Crossman Premier pellets in .17 Cal.

nothing

better way to stop pellets push to hard more than one will come out

not worth monny

Solid construction, stays in pocket/shirt well with clip

Plunger is very long when full

This thing is huge when it's full of pellets!

reduces reload time

add lanyard

This Loader is great.I would give it a top rating. It will fix in your shirt pocket and is easy to load up. I like the way that I can securely load the pellet into the barrel and seat it firmly. This will allow for a more consistent shot each time. buy this item it is a good value as is all of the crosman products

I would change nothing, Crosman pretty much has thing figured out when it comes to fine tuning their products.

Buy this to ensure you pellets are protected while being carried around... it will stop the end of the pellet from being damaged and causing the pellet not to fly true to its target...

Here the real deal on this Crosman Pellet Pen it works & works great. I own only one .177 break barrel rifle and the pen works perfectly. No more fiddling in my pockets for pellets when reloading. It works so good I want one for my three 22 cal pellet rifles but I don't believe Crosman makes one. I do know that Pyramyd Air sells a different brand for 22cal. The crosman is built tough and does have clip to hang it off your shirt or pants pocket. Very well built and worth every penny no more dropping pellets when loading.

I can't think of one thing that I would change it just works the way it is.

Compact and easy to use. Makes loading quick and simple. Holds more than enough pellets for any air gunners needs.

Nothing