Date: 25/6/2022 10:23
0

Quick-Disconnect Male Fitting + O-Ring Reviews

Quick-Disconnect Male Fitting + O-Ring

Average Customer Review

4.5 (55 reviews)
Add to Cart

In-stock

Create an online review   and share your thoughts with other customers

The most helpful favorable review

2 of 2 people found the following review helpful:

5.0 5.0

5.0 5.0

By Joe from USA on 2015-06-08 20:32:01

Things I liked:

Makes filling so much easier,hassel free filling

What others should know:

I would recomend this item

The most helpful critical review

0 of 0 people found the following review helpful:

1.0 1.0

1.0 1.0

By Michael from USA on 2022-03-06 10:00:47

Things I liked:

Didn't work as hoped

Things I would have changed:

Correct thread and size

What others should know:

Definitely will not fir Umerex Gauntlet air tank

Sort by:
Filer by:
  • 123 Next
  • 5.0 5.0

    5.0 5.0

    Verified Purchase

    Things I liked:

    It replaced the probe inlet on my old SamYang Dragon Claw with the single tank.

    Things I would have changed:

    A little less stressful on the install: It fits but it fits so tightly I originally thought I was doing something wrong or I got the wrong part. It doesn't visually match what came out of the airgun, but it did work. It requires a lot more tightening down with a strong wrench than I liked, but so far so good. I am happy to have the quick disconnect on this gun, not that old probe.

    What others should know:

    You will initially think the threads don't line up on your Seneca or old SamYang big bore air rifle. Check EVERY ONE of the Q&A of this item and see what other people experienced with their guns. If you decide to do this repair/swap/modification, you will want to put the quick disconnect on the gun finger tight to fully ensure you have not cross threaded the thing. Then gently start to tighten it down a couple turns. After this, hook up your hand pump. Don't use a compressor or tank! You want a small amount of air psi. Pump a few times and tighten while the air hisses out. repeat this until the rubber O-Ring is fully smashed between the parts on the inside... that's when the air will stop hissing out. Be gentle, be slow, and be careful. Good Luck. This was my experience. Your experience may vary, so make this repair/modification at your own risk.

  • 1.0 1.0

    1.0 1.0

    Verified Purchase

    Things I liked:

    Didn't work as hoped

    Things I would have changed:

    Correct thread and size

    What others should know:

    Definitely will not fir Umerex Gauntlet air tank

  • 2.0 2.0

    2.0 2.0

    Verified Purchase

    Things I liked:

    Nothing

    Things I would have changed:

    Make sure it fits the product .

    What others should know:

    Wrong threads. Be careful. You could destroy the threads on your rifle.

  • 2.0 2.0

    1.0 1.0

    Things I liked:

    It is easy to install,

    Things I would have changed:

    Make a better valve, I have two Benjamins Marauder and but valves failed after a short period. I retired the valves and put teflon tape on the treads and both worked. Benjamin needs to do something with these valves.

    What others should know:

    Always carry a spare especially if you are doing any kind of competition shooting. I hope one would have a compressor or you will be pumping for a long tiring time. If I knew about this before buying these Air Rifles I would have looked for a different. brand,

  • 2.0 2.0

    2.0 2.0

    Verified Purchase

    Things I liked:

    allowed me to ditch the probe type fill on my Sumatra

    Things I would have changed:

    This was not machined correctly. The male foster is not long enough, and did not allow the female coupler on my compressor to seat and lock into place. I had to mill the base of if about 2mm further down into the nut to allow it to couple properly. The threaded portion also is not the same shape or dimension as the Sumatra fill probe receiver, and required adding an extra O-ring to get a seal. Still leaks when filled over 200 Bar

    What others should know:

    Not a simple swap for a Career or Sumatra rifle.

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    ease of installation, drops right in. Now all my rifles use the same fill fitting.

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    Very Happy Fits my Sam Yang 909s So much better than the factory fill probe that comes with the gun. Since installing its so much easer then factory probe ALL PCP Air Rifles should be Made with a Male Quick Disconnect AND NOT with the Probe. and Made in USA

    What others should know:

    So much better than the factory fill probe that comes with the gun. Since installing this I have lost no air due to the factory probe

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    Very good service ,fast and good product, thx

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    Great product, works like it should.

    Things I would have changed:

    nothing

    What others should know:

    Lot better than the probe.

  • 4.0 4.0

    3.0 3.0

    Things I liked:

    Much better than the old probe fill, easy to install.

    Things I would have changed:

    20.00 for a quick connector seems way high, just sayin.

    What others should know:

    It does make the fill of my airguns much easier than the old fill probe did, get the hard dust cap to keep it clean.

  • 3.0 3.0

    5.0 5.0

    Things I liked:

    Metal Durable

    Things I would have changed:

    The picture..the one in got is shorter tappered and has a skinny o ring.

    What others should know:

    The one i received had a tappered end and the o ring was way skinner than shown it has the same threads as the original that comes on the Sumatra 2500 but is almost half a inch shorter this added with the skinny oring made it so that I was un able to fill my rifle. PA is mailing me replacement though.

  • 4.0 4.0

    3.0 3.0

    Things I liked:

    This item was received in a timely manner and in it self is a well made part. It installed easily and works well with a standard Parker Female coupling, However the Air Venturi Inline pressure Gauge, 0 to 4500 psi would Pop off at 2300 psi and I would Not recommend using that combination of parts

    Things I would have changed:

    Nothing

    What others should know:

    Do Not use the Air Venturi Inline Pressure Gauge, 0 to 4500 psi item no.(AV-00031) with this part. the Coupling Pops off at 2300 psi and permanently Damages the Coupling Sleeve

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    Easy installation on the Sam Yang 909.

    Things I would have changed:

    A threaded cap would be a nice addition. I am not sure how long the rubber cap will stay on while hunting or doing field work.

    What others should know:

    Pyramid Air is a top notch company to do business with, all of the people that I have talked with over the phone have been most polite and very helpful.

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    MAKES EVERYTHING EASY.

    Things I would have changed:

    NOTHING

    What others should know:

    TRY THEM.

  • 5.0 5.0

    4.0 4.0

    Things I liked:

    Replaced Sumatra 2500 old slide in air fill system that always leaked and needed o rings repair all the time. Followed directions on PyramydAir and unscrewed a fully pressurized system and no leak, thread in new quick disconnect fitting with no problems. Real satisfied with this quick connect fill. Would recommend purchasing,

    Things I would have changed:

    - a better cap on end when not being filled. The current item is a slide on plastic cap and can fall off

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    Works well for the intended purpose, although for my Career II I needed to reuse the original "o" ring as the included "o" ring would depress the valve in the air chamber (causing the gun to leak). For the Career II the "o" ring needs to be closer to the middle of the fixture as opposed to the end.

    Things I would have changed:

    Include a thin flat washer to help support the "o" ring on the Career II.

    What others should know:

    Eliminates the need for a different fill probe for each different rifle you might have in your "inventory".

  • 4.0 4.0

    4.0 4.0

    Things I liked:

    The item makes it easier to fill my air gun.

    Things I would have changed:

    My first one had some sharp edges and was very hard to install so I called pyramid air and they sent another one immediately. It was still hard to install but the tech. rep. said to go ahead and use pressure that he would make right any damages if it caused any. No damages occurred to my knowledge and the fitting did go in.

    What others should know:

    Pyramid air is a very efficient group with friendly service. I highly recommend them.

  • 4.0 4.0

    3.0 3.0

    Things I liked:

    Nice design works good. For filling the gun.

    Things I would have changed:

    Received two of these the first one the threads did not want to go into the barrel without a lot of pressure and the threads had a sharp edge. The second one was also hard to install but pyramid air representative said to go ahead and install anyway he would take care of it if it did damage. It did go in but it took a lot of pressure.

    What others should know:

    The manufacturer should check the tolerances on this product to prevent any damages to guns it is being installed on.

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    Easy straight forward installation.

    Things I would have changed:

    None

    What others should know:

    A good way to make your Sam Yang big bores easier to fill out in the field.

  • 5.0 5.0

    4.0 4.0

    Things I liked:

    Absolute must for the Sumatra 2500. The original fill valve that comes with the rifle is notorious for leaking. VERY SIMPLE to install and allows you to connect and fill up with any pump using a Foster quick connect coupling.

    Things I would have changed:

    A brief diagram showing where it goes on various guns.

    What others should know:

    Don't buy a Sumatra without adding this simple piece to your order. You will be disappointed if you don't as the original fill valve simply does not work.

  • 123 Next

Buy with confidence

Get FREE shipping on qualifying orders! Any order $150+ with a shipping address in the contiguous US will receive the option for free ground shipping during checkout. Certain restrictions apply.

Free shipping may not be combined with a coupon unless stated otherwise.

View Shipping Info

Text JOIN to 91256 and get $10 Off Your Next $50+ Order.

* By providing your number above, you agree to receive recurring autodialed marketing text msgs (e.g. cart reminders) to the mobile number used at opt-in from Pyramyd Air on 91256. Reply with birthday MM/DD/YYYY to verify legal age of 18+ in order to receive texts. Consent is not a condition of purchase. Msg frequency may vary. Msg & data rates may apply. Reply HELP for help and STOP to cancel. See Terms and Conditions & Privacy Policy.