Page 8 - UTG Drooper Scope Rail, 11mm-to-Weaver Reviews

Excellent product. Inclusion of extra screws and wrenches a definate plus.

Nothing

pyramids shipping,while somewhat expensive,is first rate.

Everything was GREAT.

Since I am new to air rifles... more information for installation would have been nice... Perhaps Pyramid Air can include a small info sheet. If they did it would be Great since everything else I have experienced from Pyramid Air has been Great.

No comment.

This mount was perfect for my drooper barrel. I wish it had been recommended by the Pyramid staff rather than the one they suggested. It corrected the droop so that my scope was exactly in the middle of adjusting up or down. Excellent quality.

Nothing

You cannot go wrong with this mount.

Bought this to install on my Diana RWS 34. Installed in seconds, scope mounts on it with no issues. Had the rifle zeroed in just a few shots and have had not had to readjust anything.

Would like it to be a little longer.

Very solid & well constructed.

Nothng.

Learn from my mistakes. I ordered a RWS 34, this rail, a 3x12 leapers and some other stuff and I put it all together and started shooting... I did get frustrated. Here is what I recommend to anyone new like me: 1) Shoot the gun 1st without a scope. Make sure all the screws and fasteners on your gun are snug. As you get sighted-in at close distances eventually extend your range & learn what your pellet trajectory is (how much drop the pellet has at further distances). 2) When you have that baseline mount your scope and try to keep it as low as possible to the barrel. I had to use lower rings than what came with my scope. 3) Be sure to START sighting in your scope at the distance recommended by the scope manufacturer. For me this was 35 yards - which seemed like a very long distance. Fortunately for me I WAS at least hitting the paper. My point-of-impact was very low but I was able to adjust UP enough without any further shimming.

Fite perfectly with my l Stoager X20. It reaches over the sights with the 1' rings. it's perfect, and I'm happy with my new scope and how it fits with the UTG Drooper Scope Rail. My Scope is made for Weaver Mounts & the adapter works perfectly

Nothing to change for me with the Stoager X20. It's like this adapter was made for this gun

With adapters like this- Dovetail to Weaver you can put ANY Weaver accessory you want on your dovetail mount

It works

Cheaper shipping.

If you have a spring gun with barrel droop, just get it.

Solid, well designed and came with decent hardware.

No much.

I'm a newbie when it comes to spring air guns. I put this on my new RWS34 (t06) and i'm still really low. The problem could be entirely me. Hopefully further testing will reveal the problem...

it did what it was suppose to do.

nothing

I bought this for my TF99 to add a Leapers 4-16x40 scope.i had to mod 1/4" on both ends of this mount for it to clamp correctly to the rail. The TF99's rail is not long enough for this mount and will need modded. other than that it worked very well and was on target in no time :)

Good product! Could not have zeroed rifle without it!

Better instruction's!

This was an inexpensive solution to my RWS 34P barrel droop. It worked like a charm and I never have to worry about any scope movement. It's a set it, and forget about it product.

nothing

If you don't have barrel droop it is well worth it to get the 11m dovetail to weaver conversion mount.

Very solid construction. Mounted this on my RWS 34 with T06 trigger and it hasn't moved a bit. Easy to install but the instructions aren't all that helpful.

Might need a few more degrees of compensation for the RWS 34. Could there be some adjustment within the rail itself?

May still need to do some shimming for RWS.

I like the way the mount locks up! The droop part work great on my RWS 350 Magnum!

Nothing! Works great!

I liked the open sights on my RWS 34P and was pretty accurate with them. However, I got the gun to get rid of squirrels, and there were a couple times when shooting without a scope caused me to wound, not kill, one. Time for a scope! I like how easy it was to mount this rail. Piece of cake. I like how solid it is. Rock solid! I dropped a 4x fixed scope I had on the gun, which was easy too, and the gun hits dead center on those tiny Beeman targets every time. I like that most of all!

Not a thing.

fantastic mount. use it on both my diana 48 in .22 (heavy recoil) and my diana 34 in .22 and after sighting in one time, haven't touched them after thousands of shots. they really stay put.

absolutely nothing on this fantastic mount!!!

If you have an 11mm dovetail on your air rifle and need to convert to a Weaver, this is the rail to get. Plus the compensation for droop, does the job. Once I got it on my rifle, I was able to use the factory UTG scope rings that came with my Accushot scope. After just a few shots down range, I was sited in. I didnt have to make any further adjustments with the position of the rings on the rail.

The recoil stop screw...the rail is pretty long and the distance from the stop screw to the end of the rail is a fraction longer than the dovetail grove on the rifle. So with the rail to its furthest position towards the shooter, it takes a bit of work to get the rail positioned and held on the dovetail and the stop screw in the stop hole on the rifle.

Besides the stop screw position,if you are used to quickly resting your cheek on the stock, this rail really raises your scope height off your rifle. So it takes a bit of practice to get into your scope eye.

Got this mount for my RWS 350 Diana TO6 trigger . The mount should function properly after a lot of use. Good construction ,kind of light,reasonable price.l

Why does it not have the front anchor that all the similar UGTs have?

Check to see that the trigger on your rifle is TO6 the scope rail will be longer. This mount although it does not have the front anchor it does have four heavy screws that should do the job of anchoring the mount well. The RWS 350 is a mule so you better be sure the scope mount is tight . I have a 460 and the RWS Feuerkraft they both have to function with these types of mounts. You can also use this mount on the Gamo Socom extreme.

It gives a person options that may not have a small tube diameter scope for barrel droop issues. Well made and very sturdy.

Not sure anything should change.

I bought this for my HW97k because I have one of the few rifles that my current scope with a Accushot 1 piece mount system would not compensate or be okay in elevation. When adjusted as high as I could get my scope to go I still had my pellets impacting inches below my target. I looked to a BKL drooper but they do not make one for a 30mm scope tube. I contacted the PA and they showed me this piece of equipment. It transforms the 11mm rail on the gun to be able to use my rings with my scope which are a Weaver mount system. This system with it's 4 set screws securely holds the rail system to the guns rail. Then I was able to attach my UTG SWAT 3x12x44 scope to the system securely. I was able to bring my POI up and on target! This $19 unit saved me hundreds on another scope with a 1" tube to be able to use with a BKL drooper mount. This may be your answer as well if you are in my situation.