UTG Drooper Scope Rail, 11mm-to-Weaver Reviews

Well made and easy to install

Make it longer by 3/4 inch

Use this if you are scoping a break barrel rifle.

I bought the UTG Drooper Scope Rail, 11mm-to-Weaver Adapter for my RWS 34 Classic to mount a rifle scope I already had. Easy to install, scope mounted good and it is high enough that removal of the open sights was not necessary, it all looks good together as well.

Nothing at this point.

The rail is sturdy, mounts easily and looks good. I have not had it long or used it enough to know how it will hold up over time though it seems it will last as long as the rifle.

Good price, extra screws.

None

Needed a different base for new scope and rings and this works very well.

I hadn't experienced 'barrel droop' prior to purchasing a Ruger/Umarex break barrel rifle. This mount most definitely corrects it. At 50', even after turning the elevation a half-turn down, I was still hitting the top of the target. Now I'm shooting 'ragged hole' groups with the H&N Barracuda Hunter Extreme, and dead center at that, with a gun that's definitely NOT a target rifle. There's also been no movement of the scope or the mounts. This mount really does the job.

Nothing that I could think of.

If properly torqued, the four screws on this mounting system will prevent scope/mount movement, even if there are no holes in your receiver for the staking screws in the center of the mount.

Enables you to adjust scope turret spring to high tension and still have enough elevation when sighting in scope. This helps prevent scope reticle shift.

Nothing

Excellent quality. Did what its intended to do fixed my droop.

Nothing

Mounted on Diana 45/.177 Tuned with Hawke 3-9x40 AO with UTG high strength quick detach. Was Leary of the rings at first. Re -Centered scope via V blocks. Shot 5 HN baracuda match @ 20 . Elevation 0 windage 1.5 Rt.1/2 group. Bench. I was amazed not much adjustment at all . 50 rounds later no movement at all on any ring or base mount Marks. I still cant Get over how little scope adjustment I needed to zero. V blocks are more accurate then the mirror or counting for Centering. Make a good one out of wood with a decent size base and clamp it down.

have so many different types airguns this will work with, fast easy

Had great potential to be a good transition from the 11mm dovetail to the Weaver adapter rail. The four hex screws on the Weaver adapter rail made for a firm attachment to the dovetail.

Description said this was for RWS rifles, but that it would fit any 11mm scope dovetail rail. It did not fit my Weihrauch 35 air rifle b/c only 1 of the stop pins lined up with the "holes" in my HW35. The stop pin that screwed down into the "hole" was not the right size/width/depth, therefore not a snug fit b/c it didn't fill up the hole in my Weihrauch 35. If I knew what to replace it with, I would. Should have been a picture of the bottom side or a better one from the top showing where the spacing was for the stop pins. I was able to use only the rear stop pin and I'm apprehensive it won't last for the long-term. Also, there were no directions on the correct direction to put the adapter rail on so I had to take everything off and reverse it when I found out my Hawke scope wouldn't adjust for correct POI. I didn't know whether the writing on one side of the adapter rail went on the left side or right side, haha! Sorry, I'm a retired 69 yrs old guy, new to air guns.

Check spacing & measurements of the stop pins.

Seem to be good quality and clamp tight.

Did not give me enough elevation on a cheap break barrel Crosman.

solid 4 screw mount and seems well made and fit perfect

nothing

fits my 11mm rail good and solid. I recommend it

Strong, light weight, quality construction. Nothing fancy, it does the job it was designed to do.

nothing

I mounted a 3-9x40 scope using low profile rings and this droop compensating rail to a vintage Diana Model 34. This rail brought the scope vertical adjustment down below the mid-point.

A must have if you own a Diana break-barrel air rifle and plan on using a scope with it.

Nothing

Installing a UTG AccuShot SWAT 4-16 x 56 scope I used Medium Leapers AccuShot 30mm Rings.

Inexpensive

Construction quality.

Had this on a swarm magnum .22! Complete failure and the company would not stand behind it.. Perhaps it wasn't designed to handle Mangum rifles!

Great mount. Solved barrel droop issue. Great price point

Nada

Put on my Hatsan Proxima and thats where it will stay. Had barrel droop issue at 25 yds. With this mount, I was able to dial in at 40 yards with nickel sized groups on a mostly calm day. Thats outstanding for .177 7.9gr CPHP. 16+ ft/lb energy at muzzle

Does what it says

It is built good.

Nothing

Can now use my weaver scope mounts on my crosman 1077. And the droop compensation helps to zero scope when shooting long distances...like 50 yards. Well, that's long distance for a 1077 crosman!

Quick release levers would be awesome.

If your scope runs out of elevation adjustment, and your POI is still low, give this a try. Worked for me. Actual results may vary depending on type of bb slinger, scope, and/or scope rings used.

Good quality and fit and finish

Dose what it is so posed to.

I bought it as a scope riser for an HW97 but because of the angle built into it and I was not using it for long distance shooting or correcting for barrel droop I was not able to sight in with it as I ran out of travel in my Hawke Sidewinder scope. No fault of the product!! It dose what it is soposed to.

Very well made, heavy-duty. It worked on my Daisy Powerline 880

It was made just for my Diana Panther N-Tec 22cal breakberral, and it's solid and has 2 stop pins to keep from moving.

Nothing to change.

Perfect for breakberral air rifles.