In-stock
Create an online review and share your thoughts with other customers
Sort by: | Date
| Helpfulness
| Rating
|
---|
Filer by: |
---|
5.0 5.0
5.0 5.0
rock solid. awesome quality
Things I would have changed:none
What others should know:this thing is a beast. throw your gun out of a moving bus and this mount will be the only thing left attached
5.0 5.0
5.0 5.0
Unless you need a BLK mount to counteract barrel droop, this is a great mount. I installed it and my new Hawke Airmax 3-9x40 scope on my Gamo Bone Collector about two weeks ago and couldn't be more pleased. The 40mm objective lens clears the receiver by about 1/8". Neither the mount nor the scope have moved an iota. Permatex Blue threadlocker keeps all its screws tight.
Things I would have changed:Increase the diameter of the stop pi. I pushed the pin back against the rear of the hole.
What others should know:If you need a 1", 11mm dovetail mount, buy it.
5.0 5.0
5.0 5.0
Solid mount, light weight aluminum,4 screw scope caps, scope stop pin, 3 screw mount to dovetail or 3/8" rails, sticky tape inside rings to stop scope slide, and best of all, best price for the values.
Things I would have changed:Make a longer version. Todays adjustable objective scopes increase in length to magnification. I like to see the ear on that squirrel at 30yds. Also give the length of this mount in inch's/mm.
What others should know:Years ago I bought this mount for my Gamo Hunter rifle and 4-12x40 Bushnell scope. That scope held 0 thru a lot of bumps, bangs and drops. And it was a spring rifle too. I recently purchased the Crosman TR77 NPS here at PA, thought that with this scope mount, it would be a huge improvement over the furnished rings with the rifle (read my review of the TR77 NPS) Sorry to say that where the scope stop hole is on that rifle is more to the rear than on the Gamo or the butt stock is shorter on the TR77. Moving the Bushnell scope to the TR77, I could not get proper eye relief for sight picture. PA has a great return policy. These are the best 1pc mounts for your money, and you will not be disappointed, just a reminder, that mount is roughly overall, 4" long.
5.0 5.0
5.0 5.0
Does what it is supposed to- stays put. This is my second Leapers 1 piece mount I have purchased. The first is mounted on my RWS 94 .177, and has never given any problems. So far, has stayed rock solid on my RWS 48 .22 cal. You can spend more on a mount, but I can't see where it could do anything better than this one.
Things I would have changed:The only thing I can think of would be to make it adjust for barrel droop, but shimming works just fine if your barrel is not too far out of alignment.
What others should know:It has been my experience so far that Leapers products are a very good value for the money.
5.0 5.0
5.0 5.0
Solid, well made mount. I have installed this mount on my R-11, Diana 56 TH, Diana 440 TH, and my Walther LGV Competition Ultra. There has been no scope shift. This mount represents very high value for the dollar and I high recommend it.
Things I would have changed:Nothing.
What others should know:The manufacturer installs a sticky type in the rings that hold the scope securely.
5.0 5.0
5.0 5.0
This is a solid, well designed scope mount with scope stop pin
Things I would have changed:Make a longer version
What others should know:Bought this to mount my 4-12x40 Bushnell scope to my new Crosman TR77 NPS rifle, I also got here at Pyramyd Air. This mount is roughly 4" long, using the stop pin in scope stop pin hole, mounted the scope too far rearward to achieve proper eye relief. I will be returning this mount, I really like the 1-pc mounts, but have not found one longer with a stop pin. I will have to go with 2-pc mounts.
5.0 5.0
5.0 5.0
Quality and price. It works fine.
Things I would have changed:Nothing I can think of.
What others should know:No droop built into this mount; just a standard scope mount. Does not work on a Marauder, as is. You need individual rings for a Marauder because of its magazine. You can make it work if you notch it out on the right side (opposite the screws).
5.0 5.0
5.0 5.0
Shockingly well made for the price. Unlike many other reviews claim, this mount fits 11mm and 3/8" dovetails no problem! All you need to do is flip over the side plate that's held on with the three screws visible in the picture. It has an offset so IT WILL FIT either size just fine. The one I received actually had the RO from a previous purchaser inside the box still. Claiming it wouldn't fit an 11mm dovetail... It's mounted on the 11mm dovetail of my gun right now, and fits like a glove.
Things I would have changed:As obvious as it seems, apparently a picture showing how to flip the side plate is needed on the package so people know how to use this.
What others should know:DOES fit both 11mm, and 3/8" dovetails by simply flipping over the side plate held on with three screws!
5.0 5.0
5.0 5.0
Its a solid mount, and it goes well with the leapers/utg 3-9x32 a0 scope.
What others should know:Clean the mount and the dovetail of any grease and or oil; lock this baby down and your good to go.
5.0 5.0
5.0 5.0
I own 2. One on a 640 gamo and the latest on a Beeman dual caliber 22 barrel. Both are working as advertised. No movement on the beeman at all. Great product and great service.
Things I would have changed:Nothing. I would like to see the manufacturers include 1 piece mount on their scope packges for the more powerful springers. They do make a difference.
What others should know:Spring air guns are a different animal when shooting. Read and heed the guidelines on the pyramid air websitefor shooting a springer air rifle. I did and it made shooting springer guns a whole new and enjoyable experience. I would buy 1 piece mounts for any springer.
4.0 4.0
4.0 4.0
Worked great on my Remington NPSS and Benjamin Trail NP.
Things I would have changed:Nothing
What others should know:Loctite Blue. Use it appropriately and you will be less frustrated with your scope and accuracy.
5.0 5.0
5.0 5.0
Precisely built . All the screws and mounting holes are accuretly milled. The fit for the scope is nice when setting it in the mounting rings. It incluedes Allen wrenches and extra screws. It has everything needed to mount a scope
Things I would have changed:nothing
5.0 5.0
5.0 5.0
Very solid and easy to install. Love how the base locks up tight.
Things I would have changed:It's great
What others should know:Get it, great for the money
5.0 5.0
5.0 5.0
low price, fits good.
Things I would have changed:all of the 1200 fps springers should come with this mount instead of the two piece.
What others should know:I have the gamo hornet. stock scope & mounts affected by the heavy foward recoil. had to keep adjusting the zero after 12 shots or so. this mount fixed the problem. also upgraded scope to a 4x32 UTG leapers scope also from this site. thanks P/A.
5.0 5.0
5.0 5.0
i had the rugar airhawk with the scope mount that came with it and it seamed everyday i was resiting it in. so when i seen this as cheap as it was i bought it thinking its only a 10 to 15 dollars. I bought this about 1 month ago and i have not had to do any resiting on my gun
Things I would have changed:nothing
5.0 5.0
5.0 5.0
Solid as a rock . Easy to install . Even easier than a 2 piece mount . You only have to loctite the base to the rifle . No need to loctite the rings because of the tape which prevents the scope from moving on you . Using on a Ruger Airhawk with lots of kick . Comes with allen set and screws .
Things I would have changed:Not a thing
What others should know:2 piece mounts tend to move . If one mount moves and you re-tighten , you must then re-zero your scope . Double chances for this to happen with 2 piece mount system . But with this mount You can actually remove the scope , reinstall it and as long as you don't remove the mount from the rifle , you probably will retain zero or pretty close long as you mount the scope tube in the same position . Might have to slightly adjust elevation . It's that good .
By luiscomputech from USA on 2014-03-08 |
5.0 5.0
5.0 5.0
solid. keeps scope steady
Things I would have changed:nothing.
What others should know:worked extremely well on my gamo big cat 1250, the recoil from that rifle would just wreak havoc on the stock scope and mounts. this fixed the problem.
5.0 5.0
5.0 5.0
Solid, well-made mount.
Things I would have changed:Nothing!
What others should know:This was just what my Stoeger X20S should have left the factory with! Any high powered springer needs a one-piece mount, and this Leapers Accushot is a bargain!
5.0 5.0
4.0 4.0
sturdiness
Things I would have changed:nothing
What others should know:get high ones if mounting anything with 40 objective or above
Get FREE shipping on qualifying orders!
Any order $150+ with a shipping address in the contiguous US
will receive the option for free ground shipping on items sold & shipped by Pyramyd Air during checkout.
Certain restrictions apply.
Free shipping may not be combined with a coupon unless stated otherwise.
View Shipping Info
We work hard to get all orders placed by 12 pm EST out the door within 24 hours on weekdays
because we know how excited you are to receive your order.
Weekends and holiday shipping times will vary.
During busy holidays, we step our efforts to ship all orders as fast as possible,
but you may experience an additional 1-2 day delay before your order ships.
This may also happen if you change your order during processing.
View Shipping Times
It's important to know that due to state and local laws, there are certain restrictions for various products.
It's up to you to research and comply with the laws in your state, county, and city.
If you live in a state or city where air guns are treated as firearms you may be able to take advantage of our FFL special program.
U.S. federal law requires that all airsoft guns are sold with a 1/4-inch blaze orange muzzle
or an orange flash hider to avoid the guns being mistaken for firearms.
View Shipping Restrictions
We have a team of expert technicians and a complete repair shop that are able to service a large variety of brands/models of airguns.
Additionally, we are a factory-authorized repair/warranty station for popular brands such as
Air Arms, Air Venturi, Crosman, Diana, Seneca, and Weihrauch airguns.
Our experts also offer exclusive 10-for-$10 Test and 20-for-$20 Service,
which evaluates your air gun prior to leaving our warehouse.
You'll be able to add these services as you place your order.
View Service Info
Shop and purchase with confidence knowing that all of our air guns (except airsoft) are protected
by a minimum 1-year manufacturer's warranty from the date of purchase unless otherwise noted on the product page.
A warranty is provided by each manufacturer to ensure that your product is free of defect in both materials and workmanship.
View Warranty Details
Didn't get what you wanted or have a problem? We've got you covered! Return any item in new, unopened condition along with its original packaging and any accessories that might have come with your product and receive a refund within 60 days of purchase.
Our customer service team can help determine the best course of action and provide you with some options in the event you're interested in a return.
Learn About Returns
Join the Pyramyd Air mailing list: Our e-mails are filled with new products, deals, sneak peeks, tips and tricks, contests and more - sign up today!
Airgun safety is no accident. You must be 18 years or older to buy any air gun or air rifle in our store.
Text JOIN to 91256 and get $10 Off Your Next $50+ Order.
* By providing your number above, you agree to receive recurring autodialed marketing text msgs (e.g. cart reminders) to the mobile number used at opt-in from Pyramyd Air on 91256. Reply with birthday MM/DD/YYYY to verify legal age of 18+ in order to receive texts. Consent is not a condition of purchase. Msg frequency may vary. Msg & data rates may apply. Reply HELP for help and STOP to cancel. See Terms and Conditions & Privacy Policy.
By Jeff
4.0 4.0
4.0 4.0
4 screws per ring, Distributes the hold down load on scope rings and should be less likely to have screws loosen over time.
Things I would have changed:Although 3 screws should work, add a 4th screw on the gun to dove tail rail (reason for 4 stars)
What others should know:On the advice (phone call) of Pyramyd Air, bought this Medium Height Ring mount for my GAMO Bone Collector Bull Whisper to mount a Leapers UTG 3-9x40 AO True Hunter Rifle Scope, EZ-TAP, Illuminated Mil-Dot Reticle, ¼ MOA, with 1” Tube. DID NOT WORK. Length of the scope was a good match for Bone Collector BUT the front 40mm objective lens pressed against the gun barrel to the point it was difficult to turn the adjustable front lens (should not touch gun barrel at all). With AO lens touching gun barrel, AO cover could not be installed either. Good thing I also purchase the sister mount with the HIGH 1" rings. This fit my Bone Collector, AO cover installed on front lens with 5 mm clearance. NOTE: My .177 GAMO Bone Collector has so much Barrel Droop that I was unable to adjust the elevation on the scope to zero it even tried a rear ring shim (not the fault of this mount, its a zero correction barrel droop mount). Ended up purchasing a mount that accounted for barrel droop.