Page 6 - Leapers Accushot 1-Pc Mount w/1" Reviews

Rock solid mounting to a dovetail, Great fit and finish.

Not a thing.

Do not hesitate to install one of these units. Beats 2 piece mounts hands down.

Good clamping power on gun and the scope. Mount looks good. Large allen head screws that don't strip out. I can really torque the screws for a secure fit.

Remove the tape from inside the scope rings as this stuff is messy when removing the scope later.

This is a great little mount for the money. I have it on my favorite rimfire rifle and a Gamo .177 and have never had any trouble with it other than the mess the tape leaves behind on the scope. You can use alcohol to remove the mess.

Fit and finish. Rock solid dovetail mount and stop. Huge improvement in consistency and accuracy with the Crosman 800 Quest & scope.

Not a thing.

Based upon reviews and advice given here and other forums, I replaced the two piece scope mounts/rings that came with the 4 X 32 Center Point scope packaged with the Crosman 800 Quest. I had to turn the mounting bar to better fit the dovetail, Rock solid mounting with very little re-tightening (so far).
As mentioned, three allen wrenches are included; small for the scope stop, med. for the ring screws, large for the base screws; plus 3 spare screws.

Very solid; holds perfectly

nothing

I use it on a .22 rifle, not an airgun. It isn't affected by the recoil at all.

Fit and finish...excellent great price described perfectly and works great! thanks again!!

nothing!

nope...pretty much says it all!

very nice mount used it on a remington spr-18 223 dose not move wish this was around when i scoped my rws 34 ten years ago

nothing

buy it

Looks very strongh and well built.

Nothing to change, perfect as is.

I was able to swap mount and scope to fit my other rifles very quickly without the need to re-site in the field.

Very nice.

Nothing

the whole mount is very well built and sturdy and doesnt move on my Beeman RS2 air rifle...

why change anything?, its perfect for the best price for a 1 piece mount that stays still on a springer/nitro piston air rifle or pistol

buy this mount you will be pleased for sure!!

It keeps the scope in place...I torqued all the screws 5 in/lbs. over the recommended settings with my FAT Wrench...300 shots & it hasn't budged yet.. Had 2 other sets of rings that couldn't last more than 25 shots...The extra screws were a nice touch...I wish more manufacturers would go the extra mile like Leapers did...Buy this mount!!!!

Not a thing..

I didn't lap the rings in...Should they ever come loose (Never say Never!!!), I'll lap them in & that should end any movement... So far, it hasn't been necessary!!!

Holds the scope still. No creep! Works well on my Gamo Big Cat.

Nothing

Recommended to me by the PA staff. The stop pin fits the Gamo design.

stays in place so far

lower shipping price, one more screw on mount for extra peace of mind

get it if you have a scope mount that moves on springers

Solid mount, well made.

Not much.

I bought this for a Mendoza 2000, but it was a little too long for the Mendoza dovetail, I had to file the mount a bit to shorten it. Also, it still moved to the rear after I fired several shots. So, I had to remove the vertical setscrew, and drill a depression in the top of the barrel for the setscrew to fit in - that seems to have fixed it! As long as the setscrew doesn't shear off!

Nice, solid mount. Scope stop pin. Came with spare screws and all required allen wrenches.

Not really a change but another version that would be an adjustable drooper version for breakbarrel springers. Leapers may already have one but I haven't come across it.

I'm using this on an Air Force Talon SS so there is no real recoil to speak of but the mount seems like it would hold up on a moderately powered springer.

I had previously purchased the 30mm Ring version of this at thought it was a great deal so I purchased this for one of my other scopes. This mount is solid. I am able to switch between the scope and iron sights with this mount. Each time it would go back right where I had it zeroed.

The appearance is a bit blocky. But even that is okay.

The space between the rings measures 2.28in or 58mm on my mount. This is useful info. Some scopes (like the 30mm Red Dot I have) have a larger housing that has to fit in here.

everything

nothing

good product that works just like it is supposed to.

SOLID AS A ROCK! Great value for the money!

I do not see how this product could be improved.

No surprises here. It is as tough as it looks. If only everything worked this well!

This one piece mount is built very strong. I have one on my rws 350 and it stays in place. I also have one on my QB57. No troubles on eighter gun. The screw heads are deep and uniform. I know that sounds like a given but I've had trouble with much more expensive mounts.This mount can be tightened down with out rounding your allen wrench or screw heads.

Nothing

Great value

Price, durability, and the built in stop pin. like every Leapers product i have ever owned it is reliable and not to pricey. Think gamo but cheaper.

bigger knobs on the rail i had to use an oddball allen wrench to get it tight.

Do not use on bolt action rifles if you use a bolt lock it makes it impossible to get it in their.

Very sturdy, easy to setup and stop pin is a good size.

nothing at this point in time.

I bought this for a Gamo Bat Cat. I have tried a few different mounts on this rifle but the recoil (very strong) would always knock the mount loose. These rings were my last atempt for this rifle or I was going to get rid of it. So far this mount has done the trick. I have shot may be 50 to 100 rounds and it's still perfect.