Date: 30/5/2023 20:32
0

Page 3 - UTG Drooper Scope Rail, 11mm-to-Weaver Reviews

UTG Drooper Scope Rail, 11mm-to-Weaver Adapter, Scope Stop

UTG Drooper Scope Review

4.5 (158 reviews)
Add to Cart

In-stock

Create an online review   and share your thoughts with other customers

Sort by:
Filer by:
  • Previous 1234 ... 78 Next
  • 5.0 5.0

    5.0 5.0

    Things I liked:

    This is a must have base for the Diana 48 springer. good build quality and very reasonable price.

    Things I would have changed:

    nothing

  • 4.0 4.0

    5.0 5.0

    Things I liked:

    I like the 4 set screws that hold it tight.

    Things I would have changed:

    I'd put more slant to the device...I still have to shim the scope even after putting this on the rifle

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    Very well made, love the 10 inch built in elevation and the length. This will replace a shorter version that is on my Texan big bore 45.

    Things I would have changed:

    I can not complain about anything. It is what it is.

    What others should know:

    This is a longer version approx 5 inches in length.

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    Well made and functioned as intended.

    What others should know:

    Not enough drop for the scope I was using, a cheap scope for a cheap rifle the scope was not up to the job. I used a different scope and all was well, needed to compensate for barrel droop on a break barrel air rifle.

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    When I mounted my scope on my .22 Benjamin Prowler it was shooting low at 25 yards with the scope elevation fully up. I shimmed the scope and was able to zero at 25 yards but the shims seemed like a stop-gap measure not to mention possible damage to the scope barrel. I put on this adapter and a pair of low Weaver rings and was able to easily zero at 25 yards with plenty of adjustment left should I decide to re-zero at a different distance. The rail mounts easily on the 11mm dovetail and clamps on tight. Of course being a Weaver rail the scope mounts solidly with no movement. The rail also seems to clamp on pretty much perfectly aligned left and right so only a very small windage adjustment was needed.

    Things I would have changed:

    It would be nice if the rear stop pin was a little farther back, like only 2mm. The stop pin doesn't line up with the hole in the receiver of the Prowler. This may not be a concern since it is all the way back and probably can't move any further but having the stop pin in place would be nice.

    What others should know:

    The hex screws that tighten the rail are a different size than most scope ring hex screws so you need a different size allen wrench to tighten them. The wrench is included so no problem but if you ever need to adjust it in the field be aware that you'll need to carry that wrench as well.

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    absolutely works. as advertised, locks in place and elevates and mounts true inline with the barrel (no tilt to the left or right)

    Things I would have changed:

    a 1 inch picatinny extension to the rear would be nice.

    What others should know:

    need it? do not hesitate to get it. I have several.

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    It bolted right down onto my Gamo Hornet Maxxim. It was a perfect fit and was a perfect solution for my barrel droop. I was hitting at about 8"-10" low with my scope dialed all the way up. It installed this mount and my first shots to zero the scope again were dead on. No adjustments necessary.

    Things I would have changed:

    I did have to swap out my rings because the stock rings did not fit. I had some used weaver rings that worked just fine Picatinny rings would also work.

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    Price. Another similar option I looked at was more than 60 clams. Ive used this in place of the factory provided rail on a Browning Leverage. It corrected the droop very nicely and the scope was so easy to sight in. Highly recommended instead of shimming back of scope.

    What others should know:

    Clean the screws and screw holes well before mounting. Mine were pretty oily/messy. I did not use the provided stop screws as the Browning has a built in stop at the rear of the dovetail and none of the holes lined up with anything on the top of the rifle. So far so good with slippage.

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    FIT MY DIANA AND UTG SCOPE PERFACK .

    What others should know:

    BEFORE YOU GET INTO SPRINGERS DO A LOT OF RESEARCH, THEY ARE A BITCH TO SHOOT. A LOT OF FUN.

  • 3.0 3.0

    4.0 4.0

    Things I liked:

    This mount did not work out for me. At 20 yards there was a 7" drop from point of aim. No fault of the mount...just not the correct mount for my level of droop.

    Things I would have changed:

    More droop compensation.

    What others should know:

    Gun is an RWS Diana 350 Magnum in .177

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    Ez to install

    Things I would have changed:

    Nothing pretty basic

    What others should know:

    The numbers are for how much competition you need

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    This product is very well made and with the four tension screws there is enough torque it will not shift. Comes with an extra stop screw and a tension bolt. I doubt that you will need the stop screws maybe on magnum air rifles.

    Things I would have changed:

    nothing

    What others should know:

    no

  • 5.0 5.0

    5.0 5.0

    Verified Purchase

    Things I liked:

    Well make from high quality materiai; grips dovetail securely; stop pins designed for Diana rifles with T06 trigger.

    Things I would have changed:

    No comment here.

    What others should know:

    I installed the UTG Drooper Scope rail adapter on a Diana Model 48 and a Diana Model 52. The adapter is solid. It has not shifted. Four screws and two stop pins do the job. I mounted UTG True Strength scopes on my Diana rifles. I did not use the rings that came with the scopes because they were too tall. Instead, I used Hawke low rings which made it easier and more natural to use the scope. You made not need the droop compensation provided by the mount as I have found the degree of droop varies in RWS/Diana rifles.

  • 1.0 1.0

    2.0 2.0

    Things I liked:

    Seems to be good construction!

    Things I would have changed:

    Have it set up so you have less elevation . For those of us who want to use it in air gun league it's way to much elevation. I went from not enough elevation on my scope to too much. I'm also not sure if it held up to the shock of my springer air rifle. It's not being used, I put it on the shelf. A waist of my time and money! Sad thing is it was recommended by Pyramyd Air tech. dept.

    What others should know:

    Research these products in detail before you buy!

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    THIS ADAPTER IS MADE OUT OF GOOD AND HEAVY MATERIAL. NOT CHEAP STUFF. SHOULD LAST A LONG TIME WITH NORMAL USE.

    Things I would have changed:

    I WISH I HAD ORDERED ONE WITH A NARROW UPPER RAIL. I WOULD CHANGE NOTHING ON THIS ADAPTER.

    What others should know:

    THIS IS A GREAT PRODUCT. STRONG, WELL MACHINED AND I CANT BELIEVE HOW INEXPENSIVE IT WAS FOR THE QUALITY

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    This mount worked perfectly for my needs, it seems well made and is a very stable platform for your scope rings. If you have a rifle that needs droop correction, either down or up this will do the trick.

    Things I would have changed:

    Nothing

    What others should know:

    I would buy this again if needed on another rifle.

  • 4.0 4.0

    4.0 4.0

    Things I liked:

    Well made, solid with a nice finish. High end appearance. Does what it's supposed to do.

    Things I would have changed:

    Offer in different degrees of droop correction. I used it in conjunction with Burris Signature rings with offset inserts to get the total amount of droop correction needed for my Gamo Bone Collector.

  • 4.0 4.0

    4.0 4.0

    Things I liked:

    Works we'll on my Hatsan BT65 Elite.Gave me the added rise that I needed.

    Things I would have changed:

    4 tightening bolts is a little overkill and has to be placed perfect to fit all slots in uniform.

    What others should know:

    Works best on Weaer rails.

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    Very nicely made, no issues whatsoever.

    Things I would have changed:

    Nothing

  • 5.0 5.0

    5.0 5.0

    Things I liked:

    WELL MADE

    Things I would have changed:

    nothing

    What others should know:

    I tried a different mount at first, but found I needed one that compensates for droop, this mount does. I put this on my Diana 56 and it has not moved or come loose. I shoot almost everyday, and I've put around 1500rounds thru it.

  • Previous 1234 ... 78 Next

Buy with confidence

Get FREE shipping on qualifying orders! Any order $150+ with a shipping address in the contiguous US will receive the option for free ground shipping on items sold & shipped by Pyramyd Air during checkout. Certain restrictions apply.

Free shipping may not be combined with a coupon unless stated otherwise.

View Shipping Info

Text JOIN to 91256 and get $10 Off Your Next $50+ Order.

* By providing your number above, you agree to receive recurring autodialed marketing text msgs (e.g. cart reminders) to the mobile number used at opt-in from Pyramyd Air on 91256. Reply with birthday MM/DD/YYYY to verify legal age of 18+ in order to receive texts. Consent is not a condition of purchase. Msg frequency may vary. Msg & data rates may apply. Reply HELP for help and STOP to cancel. See Terms and Conditions & Privacy Policy.