Home Blog  
Education / Training Airgun lubrication — spring guns: Part 1

Airgun lubrication — spring guns: Part 1

by Tom Gaylord, a.k.a. B.B. Pelletier

Today, I’m starting a long series on lubricating airguns. Blog reader Joe asked for this; but as I was researching the subject, I stumbled across another request that came in through the customer reviews on the Pyramyd AIR website:

“I wish that RWS or Pyramydair would explain the process and frequency of oiling these RWS rifles in particular the RWS mod 48. Everyone I talk with says the RWS owners manual is outdated and that with the new seals they use does not need to be lubed maybe for years….I purchase the RWS chamber and cylinder oil at a cost of almost $30.00 and now am told I probably will never need it? This topic should be cleared up once and for all by the manufacturer.”

Perhaps this customer is referring to RWS Chamber Lube and RWS Spring Cylinder Oil as the two products he purchased. And they do add up to $28 before shipping. Are they necessary? Should he have bought them? That’s the question I’ll start answering today.

This subject is so vast and complex that I cannot address it in a single report. In today’s report, I’m only going to look at lubricating the piston seal. That constitutes about half of the lubrication requirements for many airguns, in my opinion. In the next installment, I’ll address all other spring gun lubrication, including the mainspring and piston.

Leather piston seals
In a spring gun, the piston seal is what compresses the air when the gun fires. As the piston goes forward, the seal keeps the air in front of the piston, where it gets compressed because the only escape is blocked by the pellet sitting in the breech. If the gun’s working properly, all other avenues for the compressed air to escape have been blocked.

In the past, pistons were sealed with a leather pad or cup. Leather is an ideal material for this job. It’s rugged, lasts a long time and will conform to the shape of the compression chamber after a few shots — much like a leather shoe that eventually fits your foot perfectly.

leather piston seal
This cup-shaped leather piston seal is for a Chinese spring rifle.

To do its job, a leather seal has to stay soft and pliable, and oil is the best thing for this. As the spring gun operates, a little of the oil is consumed with each shot, so a leather seal needs to be oiled frequently to stay soft. How frequently? In some older guns, I’ve found that oiling every few weeks is necessary if they’re shot a lot. Certainly, all guns with leather seals need a couple drops of oil at least once each month if they’re to be shot. You can leave a gun with leather seals unoiled for years if you don’t shoot it; but before you start shooting it again, that seal needs to be oiled. When I start shooting an older gun that I know has leather seals (I use references for finding out things like this), I put about 10 drops of oil through the air transfer port and let it soak into the seal for at least an hour, although a half day is even better.

What oil to use?
The type of oil you use depends on the velocity of the gun. Guns that shoot less than 600 f.p.s. in both .177 and .22 caliber will be oiled with regular household oil. Any petroleum-based lubrication oil will do. Yes, gun oil will also work. For guns that shoot faster than 600 f.p.s., I use silicone chamber oil, like the product listed above. The spring cylinder oil is not for chambers and should not be used on the piston seals of these guns.

Synthetic seals
Starting in the 1950s, manufacturers began experimenting with piston seals made from synthetics. Some of them, like the ones used by Anschütz and Falke, worked well and lasted for many decades. But others, such as the seals used by Walther on all their airguns and the seals that Feinwerkbau used on the 121 and 124/127 sporting rifles, were made from a material that dry-rotted within about 20 years. If they were oiled by anything, they failed even faster. These seals started out as a light beige color, but as they absorbed oxygen and oil, it turned them dark yellow and brown until they began to break apart in waxy chunks.

Diana was one of the last companies to switch from leather to synthetic, and they had the benefit of watching the others. They were still using leather seals in their powerful model 45 rifle in the late 1970s, at a time when that airgun had broken the 800 f.p.s. “barrier.” When they started making synthetic piston seals, they used a blue-colored material that was tough and long-lasting. It’s interesting to note that the others adopted similar piston seal material when they finally realized their seals were perishing in use.

Diana piston seal
The blue Diana parachute seal is so rugged that hobbyists use it for many other airguns. It needs very little oil!

modern FWB piston seals
These 2 FWB 124 seals are made from modern synthetic material, yet they look like the original ones. The one on the right has been inside a rifle for a few thousand shots. It looks bad but is still in great shape and will last for many decades.

Don’t fixate on the color blue for piston seals! These synthetics can be colored any way and still be fine. I have modern FWB 124 seals that look similar to the old seals in color, yet they’ll last indefinitely. It’s the material, not the color.

Which oil to use?
With synthetic seals, I always use silicone chamber oil. That’s SILICONE CHAMBER OIL — not brake fluid, silicone spray lubricant or any other concoction. Chamber oil is for piston seals. It does not lubricate metal parts because the viscosity is too low. It’ll ruin metal parts if you use it that way. On the other hand, nobody knows what will happen to a gun that’s lubed with anything other than SILICONE CHAMBER OIL.

Diana recommends using two drops of chamber oil on the piston seal every 1,000 shots, and one drop on the breech seal at the same time. That’s it. To answer the person who asked if he needs the chamber oil, the answer is yes. But one small bottle will last a long time. I’ve observed that most Diana airguns can get by with even less oiling than what’s recommended. One diagnostic for when a gun need its seal oiled is when the seal honks like a goose as the gun is cocked.

Silicone chamber oil has a high flashpoint. Since the air in a spring-piston gun reaches about 2,000˚F with every shot, this is important. This heat is adiabatic — it doesn’t heat the gun because the interval is too brief.

Overlubing vs. underlubing
It’s almost impossible to overlube a leather piston seal. And it does not harm the seal if you do.

On the other hand, overlubing a synthetic seal can start the gun detonating. Not dieseling — most spring guns diesel. When you smell burning oil, your gun’s dieseling. Dieseling is just a few oil droplets vaporizing with each shot. It’s perfectly normal in a spring gun.

Detonation is when a lot of droplets vaporize and cause an explosion. That will damage your piston seal if it’s allowed to continue for a long time. It can also break your mainspring.

So, dieseling is okay, but detonations are bad. And overoiling synthetic seals causes detonations.

Do you see why I had to cover just the piston seals today?

author avatar
Tom Gaylord (B.B. Pelletier)
Tom Gaylord, also known as B.B. Pelletier, provides expert insights to airgunners all over the world on behalf of Pyramyd AIR. He has earned the title The Godfather of Airguns™ for his contributions to the industry, spending many years with AirForce Airguns and starting magazines dedicated to the sport such as Airgun Illustrated.

250 thoughts on “Airgun lubrication — spring guns: Part 1”

  1. B.B., Thank You for creating an online, encyclopedia of Airgun Knowledge!
    As stated previously,I’m Stuck! and swear to always, make sure I can’t answer my own question, before I ask it,(Good luckw/that!)

      • Reb, it sounds like someone’s got a little ADD….. lol, right there with you buddy! Is that beeman the dual caliber model? I bought one that was so filthy it was ridiculous, the chamber had chunks off something and within a few shots ground to a halt. This was before I did any mechanical work on them or I would have opened it up and cleaned it all out, it was a solid gun that looked nice but if the internals are shot that’s no good. Returned that one. Heavy as an old TV too. Overall evaluation from me is it would sit or sell, probably wouldn’t take it for free besides to sell, at least not if they’re all even close to as dirty as the one I got. Id love too see other guns with the quick change caliber option. – Long day today, early day tomorrow, Goodnight evrybody

            • What does BB have? ADD.

              I would of never known. I had that before so I know there is a cure. First you have to find out what started the problem. Then you start putting on the medicine to reduce the problem to see if the medicine works.
              All I know is ole Gunfun1 was sad at that time. But it was all better after he got it all balanced out again after the medicine worked.

              • Oh I forgot the most important thing about ADD. Usally its not the person that you think that has something wrong. Its somebody else!

                And all that time they thought back when I had that it was me.

                So you will find out about this type of ADD that that BB is really ok. Same as they found out about me.

                  • TT
                    This is the first time ever that I heard of you being confused.

                    And Im a bit confused also now after reading what I wrote.

                    What and the heck am I talking about. Yep to much wild turky. I need to go to sleep.

                    Ignore what I said. See I got to sleep. Really

                    We really need a edit button you know.

                    I should shut up now!

                    • Careful with that Kickin’ Chicken! I remember giving myself 4 stitches after a knife sharpening debacle, while rather well lubribricated with it!

                  • Phew. And they say that stuff is suppose to be good for a tooth ache.

                    Wrong! I still got the tooth ache and now a head ache! I should of known better. But it was ok at first. 🙂

                    And now I got to go out and move that wood and stack it from that tree that fell the other day. Hopefully I can get done and get some shooting in. Its nice out.

          • If it is a Beeman RX-2, it is made in Germany by Weirauch. If it is a RS-2, it is made by Wang Po Industries in Chea Po, China. If it is made in Spain, it is not a RX-2.

            If someone is selling one for that price, they either really like you, have no idea what they have or it is a scam.

            • MADE IN SPAIN was stamped on the left side of the breechblock. There was also a Chinese Beeman beside it and a “pump air rifle” that felt like a fully loaded AR15 for $150, wasn’t interested in much else once It clicked.

            • Thanks for the info, buddy. Looks like someone swapped barrels on it. I guess whatever it is it’s more than likely worth $80, And I can put it on layaway for $14. I’ll be lookin’ at it again today while I’ve got the money in my pocket. Imagine a .20cal 30fpe $1000 gun on MY wall! The laminated stock makes absolutely no sense to me. I can only hope it’s for structural integrity because it’s uggly!

              • Reb

                Laminated stocks may be something like plywood in a couple respects.
                You have different runs of grain with glue holding them together. It becomes more stable and less prone to warping . The grains tend to reinforce each other and will have less tendency to split. Then there is less tendency to have a resonance .

                twotalon

        • When I held this gun i got dizzy. No, I’ts not the one at Wally’s.I got one of those back when I first saw them but had to take it back for the $.This thing is the biggest, most heavy duty air rifle I’ve ever held! I needa headsup on what to look for on it, didn’t even find the caliber stamp.
          It’s been a while since I made $1000 in one day.

          ~Daddy needs a new pair o’ shoes~

          Reb

          • Reb,

            The “MADE IN SPAIN” stamp on the breechblock leads me to believe the gun you found is a Beeman RS2. Some of the RS2 had laminated stocks.

            The Beeman RX2 was made by Theoben of England for Beeman. You would find the name “Theoben” on the breechblock and on the side of the tube. All of the RX2’s came in a laminated stock.

            kevin

            • If I recall correctly, it said Beeman RX2 on the spring tube. I’ll be taking a second look in a couple of hours,We”ll know for sure then! Stuff like this drives me nuts!

            • You were right and I’m Definitely not interested in it but it did have a nice trigger. They go down by the week at this pawn shop. hmm buying a gun for a trigger?

  2. BB
    I guess Im going to be asking for it after I ask this guestion. And remember most of my guns have been pump, pcp and Co2 and I forgot nitro piston guns.

    I have 2 spring guns to my name. One is the 54 Air King and the other is the Stoeger X20.

    Im just going to talk about the 54 because its the oldest. Im going to say its about 11 yrs old. It came with the little bottles of lube that you talked about above.
    There was a schedule for maintenance that came with that gun. Here is the problem. I never followed the schedule. The gun has been lubed maybe a dozen times over the years.

    And here is the other thing about it. I got the chrony almost a year after I got the 54 and this is the thing It still chronys the same.

    So am I lucky with my results or what? And remember BB I asked about those flat Torrington roller bearings in the 54. Well I still want to do that also.

    • Hey I thought that was my stoeger x20!? Hehe, I do need to buy something with some really quality in it, I might have to ….make you an offer….you can’t refuse….. lol. I have yet to own any airgun I really just LOVED and feel like Id have in 5 years still.

      • RDNA
        I have really been wanting a TX 200 Mark lll for some time. But I keep buying other guns knowing deep down inside I should be putting money towards the good one if you know what I mean.

        When you get a good spring gun in your hand you will not want to get rid of it.

        I shot some pretty heavy hitting firearms in my younger days. And I will say I dont enjoy that kick any more. Thats why I shoot the buttery smooth pcp’s these days.

        The 54 falls pretty darn close tp that buttery smoothness. And from the way every body talks the TX mark 3 is like that also.

        Beazer where are you.. You got a TX. You know how they are better than me. (sorry to call you out again buddy but they made me do it)

        I dont know about you all. But airguns can be very addicting.

      • You are buying some pretty cheap stuff if you think the X20 is quality. Don’t get me wrong, I am sure Stoeger has it all over Wang Po Industries, but they ain’t Air Arms or Weirrauch or Feinwerkbau, etc. If you hunt around, you can get some real sweet deals on quality.

        I just picked up two FWB 300S’s at an unreal price. They need new seals, but that is no biggie. My 1906 BSA needed rebuilding, but because the quality was there, it could be done and without that much effort. That tiger striped walnut stock looks real nice also.

        • RR
          Oh I knew the Stoeger wasnt quality. i was hoping that maybe they would introduce a smoother spring gun with the technology thats available today.
          And I said I didnt want to talk about the Stoeger. They have thier place in time.

          But come on Crosman with the NP2. And you know whats bad about it all. I will buy one for myself to try. No matter what anybody else says about it. Sorry stuborn ole Gunfun1 again. 🙂

        • Stoeger is probably better quality then I’ve been able to buy, the NP is the first gun I’ve bought over one hundred bucks, that had been my limit for a long time. If I put all the hundred dollar guns I’ve bought together Id have an evanix 3D rainstorm by now! I’ve never been with much money, and when I did make 800 a week I wasn’t airgunning at the time, too busy with bills girls and being a bad boy! Now I survive well enough but there is no extra money for toys… 🙁 I have to sneak them in, what I need to do is sneak my next three toys together,( about 6 months+) and get something nice.

          • Heh… For many years $100-150 was my price range for fountain pens… In that range they used to come with at least a 14K gold nib. One had to check the specifications closer for those in the $75-100 range. Below $75 tended to be highly polished, maybe plated, steel.

            Now? Steel nibs are common in pens selling for $200. Bexley, I believe will allow one to order a gold nib… for $200 extra 14K, and more like $300 more for 18K.

              • RDNA,

                Fountain pens are highly collectible! In fact, there was a time when B.B. was interested in collecting vintage fountain pens. It never took off, however, because they’re not as much fun as vintage guns 🙂

                Edith

              • Scrawl… (my hand-writing is that bad…)

                I’ve been using fountain pens since the end of the 60s — 6th grade.

                A good one (which, strangely, more and more seems to be the cheap steel nib models — Lamy AlStar, for example) have good ink flow, and need NO pressure on the paper. Makes for fast writing without much strain on the hand.

          • RDNA
            Some of them hundred dollar guns can be winners. I just got one of the Daisy 953 target pros with out the sights.

            I left a comment about it farther down where RR but up the link about the Walther LGV and the Torrington bearings.

            But you got to get your hands on one PCP gun for a day of shooting. You will be hooked. Now what needs to happen I believe more than ever is if Crosman is going to take on the $100 PCP they need to get on the ball with it. Even though I have some high end guns and qiute a few of the lower end guns. I will buy a hundred dollar PCP if Crosman makes it. Even if it is loud.

      • I too thought of getting a X20, but I knew that before I even shot it the first time, I was going to have to put a new trigger in it. Then I was going to have to drop a few hundred bucks on a stock. It would be cheaper for me to buy a TX200 M3 with a walnut stock or a HW 35.

        I am not going to have a room full of these things so why not just have a few really nice ones?

        • RR
          And thats what Im talking about. You know what kind of PCP guns I have.

          And look at my 54. Sooner or later the quality top end performance bug will get you.

          I got a Daisy single stroke on the way right now. I bet you know whats going to happen to that gun RR. I will put it this way. I will not be able to keep my hands ofg of it if you know what I mean.

          By the way how is your AirForce project going?

  3. Hi B.B.

    I’m sure you can read minds Sir. I was just hoping for this & your timing is spot on. You see my best friend is going overseas for a couple of years & gave me his Norica Titan Basic with brand new mainspring & piston seal (synthetic) for tuning & safe keeping. I have no experience with synthetic seals so this is so timely. Its rated 623fps so do you think Singer Multipurpose Oil would do? Just a few drops or would it damage the new seal? Please keep up the Great Work & God Bless You.(the gun is 2 years old and is in super condition but the mainspring is weak cos he used to keep it cocked for long spells)

    Errol

    • Errol,

      No, on the Singer oil. It’s used for lubrication, not for sealing. You really do need silicone chamber oil for the piston seal of that rifle.

      I have never seen a synthetic seal fail in normal use, with the exception of the ones made in the 1970s and -80s from improper material. I doubt you need to do anything but shoot your rifle. Maybe ONE drop of oil (silicone) through the transfer port each year, unless the gun starts honking like a goose when cocked. Then the seal does need some oil.

      B.B.

  4. If I got this right, a couple of drops and no more of that silicone chamber oil should be safe on any spring air gun, regardless of what the seal is made of? But how can you tell if you’re shooting an under oiled leather seal? So that you could give it more of the oil it needs.

    • JPM,

      Welcome to the blog.

      Errol is right — a loss of velocity is the best diagnostic for leather seals that need oil. That’s why a chronograph is such an important tool.

      When I lubricate a gun that has leather seals during a teardown, I use a petroleum-based grease on the piston seal and also on the rear of the piston. I have a Diana 27 with leather seals I lubed 15 years ago and it still functions fine. Of course I don’t shoot this rifle that often. If I did perhaps it would have needed more oil or grease by now.

      I have many airguns, plus I’m always testing new ones, so I don’t get to shoot even my favorite guns as often as I would like. But I know guys with one or two guns they are constantly shooting. These are the fellows who need to worry about more frequent oiling.

      B.B.

      • Hey if you ever need to lighten the load, you know I could use an airgun that’s actually worth holding on to. You know a super powerful .22 springer is my cup of tea and your least favorite, so….. 😉

  5. Is there a lubricating oil that works better on rubber piston O rings?, or should i invest in some silicone chamber oil. At the moment i’m using Abbey SM 50, which i’m lead to believe is silicone based.

    • Sir Nigel,

      I’m not familiar with that product, but if it seems to work I would go right on using it. I recommend silicone for rubber piston o-rings, just to err on the safe side.

      Having said that, I lubed my battered old Meteor Mark IV seal with moly grease. So I guess I’m a bit of a two-face.

      B.B.

  6. I picked up a RWS Diana 45. The manufacture date is June 1987. Is the piston seal leather or synthetic? It currently shoots 7.9 Boxed Premiers at 690 to 695 FPS over the chrony.

    • Heat,

      This is a real tough call, but your 45 is definitely dry. I’d try 10 drops of silicone oil through the port and let it soak into the seal for a couple hours — just in case it is still leather. After that you can work the barrel up and down through couple inches of arc — not cocking it, just moving the piston a few inches. If you hear a squishing sound, the seal is leather.

      The date on your rifle seems to indicate that it was made in the synthetic seal era, but the 45 was the last rifle Diana converted from leather, so your seal may be leather.

      After the oiling job, if the velocity settles down around 850-900 f.p.s with those Premier lites, the seal is leather. If it settles at 930-980, it’s synthetic and you may have some smoke for a while.

      B.B.

  7. B.B.,

    Thanks again for another great report. The basics are most important, and often most interesting.

    I enjoyed your writings this week. Have a good weekend, and don’t forget to tell us about the airgun show.

    RB

    • Awesome! I wonder how true it will be to the original that I have. there is some major machine work in one of these. I am not so sure they can sell it at that price. We’ll see.

    • Shucks, I got all excited for nothing. They are not going to build the “Lincoln Jefferies” again. They are going to build a low powered PCP that will be inexpensive by Europe’s standards.

  8. Kansas heat ,

    Your RWS 45 has a leather seal for sure, the cutoff was 1988. If Your rifle has the cross pin holding in the trigger through the stock it is a leather seal gun. Beeman Precision sold these as the 250. Air tool oil is great on these seals and also helps lube the piston and compression tube. I have brought quite a few of these back to life with oiling.

    • Thank you Edith, BB, and Gene Salvino! I will oil this old dog as you have suggested. Unfortunately today at Noon this project moved to my ‘back burner’ list. I was informed today that my services are needed in Tulsa, OK and will be traveling that way Sunday night for up to 4 weeks. It sucks to work for a big company and not to be in full control of your destiny. I’m putting all my gun toys away and will unpack them when I get home.
      Now for some wishful thinking….are there any BB Blog Contributors that are located in the Tulsa area that I could touch base with? I’m fairly green on this whole subject and would certainly appreciate meeting more experienced shooters to absorb some knowledge.
      I’ll buy dinner and beer,
      Randy

  9. In addition to the older Walthers and the Feinwerkbau 121/124/127 series the Air Arms Pro-Elite used the synthetic seals that deteriorated quickly. Turned waxy and disintegrated.

    If you acquire any of these guns it’s a good idea to open them up and check on the piston seal. Doesn’t take long to ruin the piston and/or end of the compression tube by shooting these guns with a disintegrated seal.

    kevin

  10. OK the possible substitute that I’m considering for velocity tar is…CYCLE CHAIN LUBE-Ideal chain& cable lubricant-anti sling formula-inhibits corrosion-designed for all O-ring chains. This stuff is really sticky! kinda reminds me of what’s left inside a tire that Fix a Flat was used in. Gunk liquid wrench ML2S.

    ANY thoughts?
    Thanks

    Reb

  11. Just saw the Fed Ex truck parked across the street while making a shammich, as I walked out the door he cranked up and went the wrong way! Tried to chase him down on my bike AARGH!

  12. BB
    I visited ARH from my mobile phone could not find velocity tar, under lubricants, only found listing as large heavy tar & large clear tar is this the same stuff?

  13. Pardon, but shouldn’t that first sentence be “… lubricating airguns…”?

    A “lubrication airgun” would be a pneumatic powered greasegun at an auto shop…

  14. Help: I dropped a pellet into my cocked RWS 48 and it went inside the piston tube. I cant shake it out and because the spring is compressed I’m afraid to disassemble or fire it…any suggestions?

    • Mark,

      It’s been done before. No harm will come from firing the gun once, to uncock it. After that you can disassemble it to remove the pellet.

      I have removed as many as half a dozen lead pellets from the piston seal;s of some guns I’ve worked on.

      B.B.

        • Mark,

          Oh, no. I thought, from the way you spoke about it, that you knew how to disassemble a 48. If this is your first teardown, the 48 isn’t the gun I would recommend doing it with. There are some complexities.

          You might want to send this gun to Pyramyd AIR for a rebuild, after you have fired it.

          B.B.

  15. Hey Tom, I have a Benjamin Titan NP and I love it, very smooth shooting and fairly accurate once you find out how it liked to be held. (not every single spring gun likes or needs the artillery hold) but even after 500 or so shots it’s still dieseling. Not much, but smoke comes out of the breach after the shot.
    Should I just let it go away, or take the time to rebuild it? I’ve rebuilt my Crosman Quest 1000 and it was fairly simple.

    Thanks!

  16. I had an incident similar to Mark’s today also, as I was closing the breech on my QB-36 I felt slight resistance so I opened it for inspection, The pellet is nowhere to be found, worked it back & forth all in vain. Finally I closed the breech and felt a lil squish and pulled the trigger. A Crosman wadcutter flattened to about the size of a quarter greeted me on reopening for the next round. I figured I couldn’t be the only one.
    Go Figure!

    Reb

      • I guess so did you see what the AM is doin’-over 10 flbs, the 880 is over 8 and the QB-36 is a little over 7 alongside my 760. Then I ran outta daylight for the Red Ryder. Just took a break from the 3120. The intake seal must be mushroomed or sumpin’, The pump won’t push it out. Grrr!

  17. Help! Anybody have experience with rivets? The one for the pivot link on my 3120 was loose when I got it.A couple whacks with a pall peen got it down enough to pump it, for a lil while. I feel if it’s not attended to it will be a skeleton in my closet. This rivet takes the brunt of the force involved in pumping, It’s also countersunk and flush mount so I believe heat will be necessary but how will this affect strength? and will the heat hurt the bronze bushing/bearing?. I’m thinking, heat it away from the gun till glowing then install and whack. Sound right?

    Any input will be up for consideration and will be greatly appreciated!

    Thanks

    Reb

    • Those rivets are soft steel, Reb. You can drill it out and replace it if the hole isn’t wallowed out. If it is you can put in an oversize rivet by just peening it in with a hammer on one side and a flat bucking bar on the other. Pretty easy if you’re at all accurate with a hammer…

      /Dave

      • Dave, I can get it out but I would like to have one that’ll last, when I get done. From what I understand this is one of the few weak links on this gun. Can I replace it with something harder? I have a fastener fabricator 1 mile away. Everybody keep this in mind if you need something because these guys make ANYTHING including taps and dies! And dirt cheap!

        • I’d replace it with like material. Rivets are cheaper and easier to obtain and replace than the arm parts. Think of it as a consumable… It is the weak link for a reason. If you strengthen the rivet then the something else wears out first. Which piece would you rather replace?

            • McMaster Carr or Aircraft Spruce should have what you need. A nail will work if you anneal it (soften) first. Heat it cherry rd and slowly take it out of the flame until it no longer glows red. Then set it aside to cool slowly. You can then cut it to size (grip length plus 1-1/2 x diameter) and install it. If the head is supposed to be countersunk, you’ll need to make a form to do that.

              • Good info Dave! Just so happens, I found a magnet that fits it perfectly when I whacked it before. most magnets shatter when impacted however, this one’s already survived quite a few.

          • The one thing that really hit me when it failed, was how much damage was averted. Yeah I grabbed the whole thing! I also recall sharing an incident here(just came to mind) where the pump handle almost slipped. It felt like the valve had just dumped 6 pumps through the intake! ever heard of that?

  18. Guess I’ll have to type it all again,Grr!

    Help! Anybody have any experience with rivets? One of the ones for the pivot link on my Benjamin 3120 was loose when I got it. I gave it a couple whacks to get it down so it would clear the slot but it’s not gonna last once I get pressure on it. This rivet is countersunk and flush mount so I don’t see doing it without heat. what effect will this have on strength? There is also a bronze bushing/bearing that goes between the rivet and link. I’m thinking heat the rivet while uninstalled, insert while glowing, whack and grind if necessary. Sound right?

    Any input will be up for consideration and will be greatly appreciated!

    Thank You

    Reb

        • Reb,

          I think your internet service provider (ISP) doesn’t give you a permanent IP number for connecting to the internet. There are a LOT of IP numbers that are known sources of most spam, and I’ve added those to the spam filter over the years. So, if your ISP changes your IP number from time to time, then that explains why you can post freely and frequently most of the time but occasionally get caught by the spam filter.

          FWIW, my ISP gives us the same IP number all the time. However, if our internet service goes down and then comes back up, chances are good that there’s some repair going on & our IP number changes.

          You can check this yourself to see if that’s the issue. Go here: http://www.whatismyip.com

          Mark down the number. Whenever you write a comment that doesn’t get posted, go back there and check your IP number. Is it the same one you had when you were able to freely post a comment? If not, then that’s the problem.

          If your IP number is the same, then there’s a word in your comments that’s causing you to get kicked into the spam folder.

          Edith

          • Just in case anyone else ever has this problem,by following the steps, outlined after clicking this link,it gives you the option to change your IP address, (right?might work?). Good luck!

          • Hello Edith
            Thanks so much for this website. As it happens, I have been having problems with what I thought was my brand new iMac. Running the speed test the offer, tells me my computer is tickety boo. I have owned these ‘time saving machines’ in one form or another for over 25 years now, and it seems I’m still learning the basics today. Much gratitude.
            Ciao
            Titus

  19. B.B., So when I get into this QB-36 if it has a leather seal and it looks alright,Which would be better, the leather one or replace with a synthetic? And why? The bore on this gun is very nasty right now and I’m kinda thinking the leather seals and having to oil may be part of the reason for this. The gun clocked at about 600fps yesterday with just about anything I ran through it.

    Thank You

    Reb

    • Based on my QB36-2 (longer stroke, but very similar), you’ll likely find the leather has been torn by the cocking lever shoe slot on installation; this causes excessive dieseling and possible detonation with oiling, possibly even breaking a spring eventually. If this is the case and you clean up the cylinder, you can use whichever type of NEW seal you want, leather or synthetic. I went with synthetic (JM Apex), for the challenge (had to rig up mounting) and I’m glad I did, as it requires a lot less attention. If you don’t do much to the cylinder, install another leather seal as it is more forgiving, but do at least smooth the burr that cuts seals on installation.

      • I can only imagine how much deburring a Chinese gun would need! I feel this is one of the top most important parts of prep work. once it’s done things are easier to handle, go together easier, with less damage, it’s easy and once it’s done, it’s forever.(or until you drop it!)
        My gun’s running about 600fps,this may mean I’ll have no choice because the original is toast. I was hoping for 800, I assume this is doable and would like to start building from the ground up. Where would you start, and will a leather seal support this much power? If it’s gonna have recoil behind it, I want power in front of it!

      • Reading this all again makes me glad I used a synthetic lubricant for soaking. I figured, if it was leather and I let it soak overnight, that it should raise velocity by 10-30 percent. Today’s conditions were unacceptable for the Chrony, here, so, nothing concrete, But, no real increase after 10 drops soaking for 2 hours
        At least it’s not blowin’ up, on me!

    • Reb,

      If the leather seal is okay I would keep it in the gun. If it has to be replaced I would try to get another leather one. Leather takes care of a host of weaknesses in spring guns, including rough machining. And the Chinese synthetic seals aren’t the best.

      B.B.

  20. So no threads on np muzzle, guy wouldn’t do it if he couldn’t put it on a lathe, I didn’t think it would be much more difficult either way but he’s so anal its obnoxious, urrrggh.

  21. Does anyone know of an air rifle scope that focuses closer than 10 yards (like the UTG Bug Buster which can focus at 3 yds.) AND has a SWAT focusing knob? I already have a Bug Buster, but it doesn’t have SWAT.
    Thanks,
    Jerry

  22. Goodness ya’ll, where do I start? Anyhow, I attended the airgun show in Findlay earlier today, and for some reason my wallet is considerably lighter. Meeting Tom after reading his blog after all these years was quite the treat as well. Tom autographed my Blue Book of Airguns for me like the true gentleman he is. Also got to meet Mr. Twotalon as well which was a surprise. I went to the show with the image of a Feinwerkbau 300S burnt in my mind after lusting after one for somewhere near a decade now, and I failed at that mission, but all was certainly not lost. Another fine 10M match rifle lay on the table before me, and upon picking it up and examining it I discovered I was holding none other than a well preserved Anschutz LG-380. You see, I have a serious weakness for anything that possesses surgical accuracy and precision but always assumed a 380 would be out of my league pricewise, but this one wasn’t!. After some slight negotiation, the rifle was mine! Interestingly, someone in the past added a little artwork to the stock in the form of a rather beautifully carved and painted Ram’s head almost like a little medallion to adorn the stock, but other than that the rifle appears to be well maintained and cared for. I hope Tom shows that picture he took of it to you all because it really is rather unique and well done. After bringing it home and running some various pellets through it rather informally, I realized what a jewel I now own. I managed my first honest one hole group totally off-hand and unsupported earlier today so needless to say I’m just over the moon. Thanks again to Tom for the autograph, and I’ll be looking forward to the next installment of this blog as I always do! Take care everyone…..

    • Somehow I had a sneaking suspicion that bringing up model 25’s would elicit a reply or two… =) I have one too, but it wasn’t my first. My very first airgun for me was a god forsaken Marksman Model 1010 pistol. Cocking that pistol all day long would literally make my hands nearly bleed, but boy did I have a blast with it. And as soon as the pellets ran out, I always had my wrist rocket slingshot as a sidearm.

  23. One last thing for tonight, my buddy stopped by to see the Anschutz and try it out, and we were shooting playing cards in half on edge in no time. I don’t want to admit it, but he was actually out-shooting me on my own rifle! :::gasp:::

    • Mitch

      That kind of thing happens to a lot of people. Most often, the owner does not have a clue as to how to shoot their own gun. Now if you take two guys who both know what they’re doing, somebody is usually going to do a little better anyway.
      You do have an edge…it’s yours and you will get to shoot it more than your friend does. You should be able to wax him in no time. Enjoy !!!!

      twotalon

        • Ironically enough I almost bought a pack of Tannerite the other day. Since it doesn’t work with airguns and I don’t get out to shoot my powder-burners all that often I decided against it. Other competing companies make these little round reactive targets with a special blend that work with rimfires, and I know I’ve seen videos of people setting them off with PCPs, but I wonder just what kind of velocity or kinetic energy those thing truly require.

  24. GF1,
    The discussion of the Torrington springs got me to thinking that the new Walther LGV had something similar, so I went the their site and what they have done is the piston is free to rotate in the compression chamber. I also noticed in their video that the spring is not under any compression when it is at rest.

    http://walther-lgv.com

    A pox on them! I am going to have to end up with one of these.

    • RR
      I just watched the video. Always have liked when they show the views of the guns mechanisms.
      I just wonder how much of a difference it does make in the way the gun feels when you shoot it if a person would go to the Torrington bearings. Is that what they did?

      And I had to make a order to PA the other day for some pellets and a longer air hose for my Shoe box compressor to fill the guns instead of using my little Benjamin carbon fiber bottle. I had some Bullseye bucks saved up. And PA had that 10%+free shipping. So I got me one of the Daisy 953 target pro without the sights also. And also put a little fixed parallax, fixed power 4×32 UTG scope on it. (killer little scope, very clear)

      Cool little can killer is all I got to say too. I think its what I have been looking for. Only got to pump it once and nice and smooth when it shoots; like a PCP gun. Alot better than the Stoger x20’s vibrating kick. Been looking for something like that so I can shoot while I’m refilling the PCP guns and the Benji bottle. Of course its not got as much power. But its going to come apart today to give it a little more power I hope and the 6 pound trigger has definitely got to be worked on.

      Will see how all that goes. And time to go out and shoot for now though.

      • I don’t think they went with a T bearing. The piston is free to rotate in the compression chamber. If I am not mistaken, so does the TX 200 M3 and possibly the RWS 48/52/54’s. By doing such you eliminate the need for a T bearing as the spring will rotate the piston as it uncoils. Would it help? Maybe.

        SSPs and MSPs are in effect PCPs with an onboard pump. That is why they are so smooth when you shoot them.

        • RR
          You know I got the Monsoon. If FX makes the Independence semi auto like the Monsoon I will be all over it.

          Problem is I wont have enough money to buy it without selling a gun or two. Hmm, which one would I sell. That would be a hard decision with the guns I got now.

          But wait what am I thinking. If its semi auto like the Monsoon and you can pump it and top it off like a PCP then you know what I would probably do. Or not I like my Monsoon too.

          But here’s another thing. The cost verses value of the Benjamin Marauder. Its probably one of the better PCP guns out there for what you have to pay for it. So if Crosman made a PCP with a independent pump and offered it at half the cost of the FX Independence I think they would have a winner.

          Come on Crosman you can do it.

      • You’re really gonna love your 953 with a scope on it! The headspace mod is very easy and takes about an hour plus set time, and increases effective range substantially! The single stage part ain’t so bad but the trigger is heavy and rough, so a little trigger work would definitely be in order. Good Luck!

        Reb

        • Reb
          You just don’t me yet do you.

          I just put a little heavier spring in front of the knock valve. I took the pin out that seals the transfer port from where they cross drill it from the factory. I opened the transfer port up to about .085″ And put a bigger pin in to seal it.

          Then came the trigger and also smoothing the gun out a bit. I cut some coils off the striker spring so when the bolt and trigger was at rest like after you fired the gun. The striker spring sat in it place freely. Then the spring under the sear got a coil cut off of it. Same for the spring that controls the magazine advance.(all those springs work at making the trigger heavy) And I put just a bit of radius on the sear where it latches the striker and a bit of polishing at that point.

          I know got about a 2 pound trigger(6 pounds when it started). And the gun is more tame when it fires and the point of impact is higher now. So to me that means its making more power since the point of aim was higher than the point of impact frrom before the mods. Didn’t get a chance to chrony it before or after the mod for that fact but its hitting higher for some reason.

          How did they do that in the old days with cars before the dyno’s came out. Didn’t they call it seat of the pants tuning. Punch it and see how the car pulls. 🙂

    • Derrick,

      Thanks for the pictures. Wish I could have made it.

      My favorite caption of yours that is under one of your pictures is…”… I think the show was about 65% pellet guns and 45% BB.” Seems the show was a 110% success 😉

      kevin

        • Good catch! I rewrote part of that sentence and didn’t fix the numbers. There were more HW guns as well as vintage match guns this year than ever before. And many, many good deals. You could’ve bought at least a two or three R1’s for less than $350 each. I was really close to pulling the trigger (no pun intended) on a Diana Model 10 pistol but I’m really not in acquisition mode anymore.

    • There’s an amazingly informative pictorial/tutorial after the pictures posted here, anyone about to go into a spring gun should definitely give it a glance!

      Thanks for sharing, Derrick!

      • Reb,

        Thank you for the kind words. My co-blogger Nick and I have almost 700 posts there related to airgun repair and tuning. The index down the right side will link you to all the various models we’re covered over the years. The “older posts” button at the bottom of each page takes you back to earlier posts.

  25. Just took a peek at the 2015 Z06 ragtop. This thing is gonna be a Monster! With a 6.2L Supercharged V8 AND choice of 7 speed manual or 8 speed paddleshift, it’s gonna be major competition for the overseas Supercars, Especially once a few good tuners get busy with their projects!

    Be sure to check it out Gunfun1!

    Reb

  26. This is off topic but I watched a documentary I guess that is what it was. It was about Fred Bear. The owner and maker of Bear Bows.

    It was pretty neat to watch how they made the bows. Plus he was a hunter and a amazing shot with a bow and arrow. What I also thought was cool was he knew what it took to market a product. He made amazing films about hunting with the bow and arrows.

    Me and my daughters watched it. They thought it was good since they are both into bow and arrows also.

    Just wonder if the other people here that are into archery ever saw it.

    • I never saw that but I know Bears are really good bows. I mentioned before that I got some lessons with an archery/bow hunting pro! This guy was amazing, he could hit bulls from just miles away, his trophy room was filled with EVERY type of big game from across the globe. His pointers changed my bow shooting fast, I am a pretty good shot now, always a pretty naturally good shooter, but there’s no denying the difference. I had a question about opening up transfer ports for .22 spring/gas spring guns…. Any blogs that have any experiments with changing the size?

      • RDNA
        My daughters are both actually pretty good with the bow and arrow. I stink. I will just stick to my rifles.

        And I’m sure BB has wrote about that but I don’t know for sure off the top of my head. And I haven’t done anything on spring or nitro piston guns but I have on pcp’s, pumps and C02 guns.

        I would have to say on a spring/nitro gun its probably more critical than with the guns that I mentioned I worked on.

        • Thanks guys I read both that and the older one and ended up opening up the NP to just under an 8th of an inch, about .15, where it was maybe .10 or .11, probably didn’t change much but since no chrony, its all guessing anyway, but it feels good. The numbers from B.B.s tests say it should have given me about 20 fps. I wrote the part two for it but I just did the transfer port so that’s not on there but its not much to talk about without a chrony, anybody got an extra one for like 20$ or 40$?

          • Time to bite the bullet and spend the money! I’m glad I did and I’m glad I got the Alpha Master, at first I was a little disappointed because the Chrony itself didn’t have a readout but after using it I believe I prefer my electronics off to the side, out of harm’s way, and the jumper’s gotta be 10 yards long.
            $119, cheaper than a gun and a very valuable tool. I now know, with confidence what my guns are capable of, and I gotta couple that need work. Consider it an investment in knowledge!

            Reb

      • My transfer port experiences have all been fixing ports that are too large. If you don’t have enough restriction, you won’t see a peak in pressure that prevents the piston from slamming into the front of the compression tube. I’ve had two previous and now working on a third gun that need a reduction in port size. So, go easy if you do enlarge that port–it’s a lot easier to open it up than to reduce it. I’d recommend an all around size of 0.125″ (1/8″) for a .177, .20 or .22 cal. How the pellet fits the bore (for resistance) will also come into play at some point for any given caliber. A loose pellet fit in the barrel means it’ll be halfway down the barrel (or gone) before the piston can build that cushion of air –and then it slams into the front of the compression tube. You’ll hear this as a “ping” at the end of the shot cycle. Piston weight is also a factor. And I think a heavier piston needs a bigger cushion of air. But I’m not saying that all heavy pistons need a small port. And I’m not sure that very low powered guns need small ports. But I do think there several factors that interplay and it’s not a one size fits all answer.

        • Sorry, my measurements were way off, it is now opened up to exactly an 8th of an inch, so its .125, and it was just under that to start, probably 3/32 Id say. The pointed Benjamin’s fit blatantly loose and those get the ping, the domed fit tightest and shoot smoothest so It definitely wants fat pellets.

      • Matt61
        I don’t know how some people are so good at the bow and arrow. It looks so simple but all the things there are to learn. (kind of like how airguns are I guess)

        I don’t know if I should relate the two together here but what is funny is I could shoot the heck out of a wrist rocket in the day. But not the bow and arrow. So I’m wondering where the heck my daughters got it from.

        They both hold the bow straight up and down. And they have both arms positioned right.

        I just hope they continue the interest of guns and bows. I remember what happened to me when I was a teenager.

  27. Piston seals are on my mind after the one on my IZH 61 gave out after 100,000 shots. But I don’t think it was from lubrication but from the very dumb thing that I did.

    Matt61

    • I think your piston seal was simply worn out from all the shooting that you do. It’s really hard to kill a seal with a few dry fires in such a low powered gun.

  28. B.B.

    Great blog today! This report is a gem that I needed to read–and reread often! I admittedly overuse silicone chamber oil on my spring and gas piston air guns.

    In addition, I do have one question: How does silicone chamber lube ruin metal parts? I, incorrectly, have been using a few drops of silicone oil on the cocking linkages and occasionally on the gas pistons and springs. Well, we live and learn. But, surprisingly, they have suffered no ill effects regarding their performance–yet.

    Thanks again for the much-needed report.

    Mike

    • Zuwain,

      The installation is obvious, once you have the piston and seal in hand. You simply button it onto the piston.

      Have you read the 15-part report about the 124 in which we show that?

      /blog/2011/02/a-shrine-built-for-a-feinwerkbau-124-part-15/

      Look at parts 12, 13 and 14.

      B.B.

  29. I’m still completely confused as to how often I should use chamber lube in my Crosman TR77 with a metal spring. The owners manual say one drop every 250 shots. One drop affects my accuracy for so many shots if I used it every 250 shots I would only have about 100 accurate shots before I needed to apply another drop of oil. I should note that I am using 100% silicone chamber lube by Alchemy Gun Werks Which has a slightly higher viscosity than RMCoil. I’m wondering if RMCoil burns off faster and needs to be applied more often. I’ve read I should lube the chamber 3,000 to 5,000 shots, not every 250 as stated in the owners manual.

  30. I have an RWS 52 Deluxe that I bought years ago but haven’t shot much until recently.
    Finally got a scope (Nikon Pro staff target EFR) that has parallax done to 10 meters.
    Any way the accuracy (consistency) seems to have really dropped off. I thought maybe the seals had dried out.
    I too bought both oils a long time ago but had forget the procedure so I broke down & read the instructions.
    1. Does long term storage change the rules for lubrication?
    2. Could I have damaged something by firing cleaning pellets?
    3. Too much recoil for this scope?
    Any suggestions would be appreciated.
    Thanks for the timely article,
    Brian Ward

    • Brian,

      Welcome to the blog,

      1. Long term may affect lubrication, depending on the lube and how long. My guns have been lubed past 15 years and are still fresh. Today’s post talks about this subject. Read it here:

      /blog/2015/03/rws-diana-45-part-7/

      2. Cleaning pellets are not meant to be shot. They are to be pushed through the barrel with a cleaning rod.

      3. A 52 can damage a scope, but if the scope’s elevation is set too high because you have a drooping barrel, then the scope may be fine, but unable to hold zero. That is the cause of 99 percent of accuracy problems.

      B.B.

      • The 52 is a side lever so I’m not sure if the reference to the 45 applies.

        The instructions for the RWS cleaning pellets say to “fire the cleaning pellets as you would a regular pellet”.

        Again, the 52 is a side lever rifle, so I’m confused by the reference of a “drooping barrel”.

        • Brian,

          The fact that the 52 is a sidelever has nothing to do with how the gun operates. It is still a spring piston powerplant. The cocking method is divorced from the rest of the powerplant.

          Now, the 52 does have a sliding compression chamber, and that does make a difference in some ways — though not in the one we are discussing. And the 52 does have a synthetic piston seal that makes all the difference in the world. My answer was suited to guns with leather seals — not synthetic seals, so you were right to question what I said.

          As for RWS telling you to fire the cleaning pellets, you have to remember that these companies are staffed with people for whom the job is just 9 to 5. They are not airgunners, and many times what they write in the instructions for their products is something they have read in other instructions for things the company sold many years before. In other words — they simply do not know and are not interested in finding out.

          “Cleaning pellets” are simply pieces of felt that a marketeer sold in the 1970s to airgunners for cleaning guns that are far less powerful than they are today. They are a poor joke and a travesty, foisted on an unsuspecting public by marketeers who have no idea whether they work or not.

          Dr. Robert Beeman, whose company sold these cleaning pellets, revised his instructions for using them several times, when he discovered they do not cushion the blow of the piston like lead pellets do. His final instructions were to load as many as 6 cleaning pellets in-line in the barrel, in hopes of cushioning the piston blow. Airgunners soon discovered that was impossible to do, and in the late 1990s there were lots of discussions of the “right” way to use felt cleaning pellets.’

          Today the accepted method is to push them through the bore one at a time with a cleaning rod, which is the same as pushing a patch through. So, why waste your money of a product that doesn’t work?

          But the fantasy of cleaning pellets will continue, because the retailers haven’t got a clue about how they really work or how to use them. And their title — “cleaning pellets” — sounds so right to people new to the hobby.

          Now, to the barrel droop situation. Droop isn’t the right word. Downward slant is more correct, and, yes, fixed-barrel airguns can have it. In fact, the Diana (not RWS) 48/52 is notorious for being a drooper. That’s why I developed an anti-drooper base for the rifle with Leapers several years ago. Tens of thousands of fixed-barrel sidelever Diana 48 and 52 rifles were finally able to hold a zero, because their scopes are no longer adjusted too high. Read the 3 articles I wrote about mounting scopes and sighting them in on the articles page.

          /articles

          /article/All_about_scopes_Part_1_January_2005/19

          /article/All_about_scopes_Part_2_February_2005/21

          /article/All_about_scopes_Part_3_April_2005/22

          When a scope is adjusted too high, the erector tube that contains the reticle starts to “float” or to bounce around with the vibration of each shot. This is the number one cause of a scope that won’t hold zero and is responsible to a high percentage of scope problems. Get that scope closer to the center of its adjustment range and it suddenly starts to work as advertised.

          B.B.

  31. I have a Model 48 Diana RWS side cocker and would like to know what type of piston I have and where to oil the air rifle. I have bought many years ago Pyramid and would like to know what of oil to use, I have a plastic bottle of Beeman oil, I would like to know if I can use this oil on my RWS. The air rifle was bought about 10 years ago from Pyramid air what is recommended for this air rifle. Plus I have a Benjamin Nitrogen piston air rifle and can I use the same oil or what type of oil.

    • Robert,

      Welcome to the blog.

      Your Diana 48 sidelever can accept one drop of silicone chamber oil through the air transfer port every 3,000 to 10,000 shots. The air transfer port is the hole in the center of the sliding compression chamber. I don’t know what kind of oil you have, but it must be silicone chamber oil with a high flashpoint so it doesn’t detonate when the gun fires. If you read on the Beeman bottle the words silicone chamber oil, you can use it.

      A Diana spring gun doesn’t need much oil. I never oil mine at all. The piston seal is self-lubrication to a large extent.

      The Benjamin Nitro Piston II is a gas spring powerplant that also doesn’t need much oil.

      Basically these guns only need to be oiled when they start squeaking when they are cocked.

      B.B.

Leave a Comment

Buy With Confidence

  • Free Shipping

    Get FREE shipping on qualifying orders! Any order $150+ with a shipping address in the contiguous US will receive the option for free ground shipping on items sold & shipped by Pyramyd AIR during checkout. Certain restrictions apply.

    Free shipping may not be combined with a coupon unless stated otherwise.

    View Shipping Info

  • Shipping Time Frame

    We work hard to get all orders placed by 12 pm EST out the door within 24 hours on weekdays because we know how excited you are to receive your order. Weekends and holiday shipping times will vary.

    During busy holidays, we step our efforts to ship all orders as fast as possible, but you may experience an additional 1-2 day delay before your order ships. This may also happen if you change your order during processing.

    View Shipping Times

  • Shipping Restrictions

    It's important to know that due to state and local laws, there are certain restrictions for various products. It's up to you to research and comply with the laws in your state, county, and city. If you live in a state or city where air guns are treated as firearms you may be able to take advantage of our FFL special program.

    U.S. federal law requires that all airsoft guns are sold with a 1/4-inch blaze orange muzzle or an orange flash hider to avoid the guns being mistaken for firearms.

    View Shipping Restrictions

  • Expert Service and Repair

    Get the most out of your equipment when you work with the expert technicians at Pyramyd AIR. With over 25 years of combined experience, we offer a range of comprehensive in-house services tailored to kickstart your next adventure.

    If you're picking up a new air gun, our team can test and tune the equipment before it leaves the warehouse. We can even set up an optic or other equipment so you can get out shooting without the hassle. For bowhunters, our certified master bow technicians provide services such as assembly, optics zeroing, and full equipment setup, which can maximize the potential of your purchase.

    By leveraging our expertise and precision, we ensure that your equipment is finely tuned to meet your specific needs and get you ready for your outdoor pursuits. So look out for our services when shopping for something new, and let our experts help you get the most from your outdoor adventures.

    View Service Info

  • Warranty Info

    Shop and purchase with confidence knowing that all of our air guns (except airsoft) are protected by a minimum 1-year manufacturer's warranty from the date of purchase unless otherwise noted on the product page.

    A warranty is provided by each manufacturer to ensure that your product is free of defect in both materials and workmanship.

    View Warranty Details

  • Exchanges / Refunds

    Didn't get what you wanted or have a problem? We understand that sometimes things aren't right and our team is serious about resolving these issues quickly. We can often help you fix small to medium issues over the phone or email.

    If you need to return an item please read our return policy.

    Learn About Returns

Get FREE shipping on qualifying orders! Any order $150+ with a shipping address in the contiguous US will receive the option for free ground shipping on items sold & shipped by Pyramyd AIR during checkout. Certain restrictions apply.

Free shipping may not be combined with a coupon unless stated otherwise.

View Shipping Info

Text JOIN to 91256 and get $10 OFF Your Next $50+ Order!

* By providing your number above, you agree to receive recurring autodialed marketing text msgs (e.g. cart reminders) to the mobile number used at opt-in from Pyramyd AIR on 91256. Reply with birthday MM/DD/YYYY to verify legal age of 18+ in order to receive texts. Consent is not a condition of purchase. Msg frequency may vary. Msg & data rates may apply. Reply HELP for help and STOP to cancel. See Terms and Conditions & Privacy Policy.