Date: 19/12/2018 12:5
0
The Winter Sales Event is here! Product Discounts + 2x Bullseye BucksSHOP NOW

Hawke Sport Optics 1-Pc Elevation Adapter, 3/8" to Weaver Rail

4.018 reviews
Hawke Sport Optics.

Roll over image to zoom in

Share your images

Lifetime limited warranty

PY-A-4163

$24.99

List Price $26.99 Save $2.00 (7%)

Add to Cart

In-stock

Estimate Shipping

Add to Compare
Add to Wish list

  • Description
  • Customer reviews
  • Q & A: 7 answered questions

Hawke Sport Optics 1-pc elevation adapter

  • 3/8" to Weaver rail*
  • Rail has some elevation built in to it
  • Compensates for droop
  • Up to 100 MOA of elevation adjustment
  • Includes a rail and a hex wrench
  • 0.63" high
  • 5.4" long
  • Black


*3/8" is approximately 9.5mm, but this adapter has enough room in it to accommodate up to 11mm.



If you need to convert your air gun's 3/8" or 11mm dovetail to a Weaver, this 1-piece rail will do it and offer a firm, secure foundation for your optics. The elevation in this adapter will help compensate for any droop you have in your air rifle.


In stock


Item Code: Hawke-22403 [PY-A-4163]
See manual

other products by Hawke Sport Optics

Average Customer Review

4.0 (18 reviews)

Create an online review and share your thoughts with other customers

4.0 4.0

5.0 5.0

By Scot from USA on 2018-04-16
See all my reviews
Was this review helpful?
0.00 ratings

Verified Purchase

Things I liked: The mount does exactly what I needed-compensate for massive (16" at 25yds, i.e. 64MOA) barrel droop on a Beeman R7. I'd tried using the scope adjustments but the scope shift was unacceptable. Other mounts didn't have the range of compensation I needed. After about 200 shots the scope is still solidly in place and the elevation hasn't changed. It's long enough that I was able to find the best ring spacing for the eye relief my scope requires.

Things I would have changed: The reason I gave it 4 stars instead of 5 is the design makes changing elevation tedious. You have to remove the scope to get access to the adjusting screw. Fortunately, you can leave the lower rings on unless you have to cover the screw with the rear ring. The mount does not come with instructions so you have to download them as a .pdf file that is available on the product description page. You have to loosen the screws that attach the mount to the rifle so it's possible to loosen them too far and have the mount shift position (there is not stop pin) when you change elevation. The elevating part of the mount doesn't have to be loose to adjust it, it will move if slightly snug. None of these things prevent me from recommending the mount.

What others should know: DOWNLOAD THE INSTRUCTIONS AND READ THEM! Some of the features of the mount are not obvious. For instance, there is a pin at the front of the mount. It's to be used if your rifle has a flat "ledge" between the receiver and the barrel and acts as a stop pin. If the receiver smoothly transitions to the barrel as mine does, remove the pin, it just pushes out. The elevation screw is NOT a stop pin. Putting it into a stop pin hole will cause it to break. Make sure the elevation screw is contacting the top of the receiver, not dropping into a stop pin hole. The mount is intended to be sighted in at 20 yards. At that distance each complete turn of the elevation screw moves the point of impact 7." Knowing this makes adjusting the mount MUCH easier. Be sure to use the set screw in the end of the mount to lock the elevation screw and press down on the scope before you lock the elevation to make sure it is firmly against the receiver. Most negative comments were from not reading the instructions.

5.0 5.0

5.0 5.0

By Kevin from USA on 2016-11-11
See all my reviews
Was this review helpful?
0.00 ratings

Things I liked: Well made,sturdy mount.scope hasnt moved yet.

Things I would have changed: Nothing

What others should know: Great mount would buy it again

 

5.0 5.0

5.0 5.0

By Mike from USA on 2015-04-12
See all my reviews
Was this review helpful?
0.00 ratings

Things I liked: Easy of use and fit correctly the first time

 

Create an online review and share your thoughts with other customers.   Show Other Reviews

Got a question? Got an answer?
Log in, then enter your text.

  • Lawrence from USA asked:

    The weaver dovetail extends past the 3/8" dovetail. How long is the 3/8" dovetail at the bottom of the unit that fits on an airgun barrel?

    • Tyler from USA:

      A little over 4.5"

  • Tony from USA asked:

    this work for uzi?

    • Tyler from USA:

      No

  • Richard from USA asked:

    The overall length is 5 1/2", how long is the dovetail portion? Is the 100 MOA adjustable or fixed and if fixed, how does it adjust? Does it keep the scope rings aligned so that they doen't add stress to the scope tube?

    • Cory from USA:

      The 5 1/2" is the dovetail portion, it is adjustable MOA by loosening the set screw and turning the adjustment screw on the top of the base then re tightening the set screw. The top portion of the base is 1 piece so it will not stress a scope tube as the rings will be aligned.

See all discussions

Navigation