Date: 25/4/2018 8:4
0
SPRING CLEANING: 10% OFF + 2x REWARDS + FREE SHIPPING* Use Code: SPRING-18
*Some items excluded. Can be combined with free ground shipping on orders $150 or more to the contiguous U.S. Expires April 27th, 2018 at 3 a.m. EST.

Leapers Accushot 1" Rings, Medium, 3/8" Dovetail, 4 Screws/Cap

Leapers Accushot 1" Rings, Medium, 3/8" Dovetail, 4 Screws/Cap

Roll over image to zoom in

See customer imageShare your images

Lifetime limited warranty

2X Earn 24 Bullseye Bucks

PY-A-793

$11.99

List Price $14.99 Save $3.00 (20%)

Add to Cart

In-stock

Estimate Shipping

Add to Compare
Add to Wish list

  • Description
  • Customer reviews
  • Q & A: 10 answered questions
  • 1" rings
  • Medium profile
  • Fits 3/8" dovetail
  • 4 hex screws/ring secure the scope
  • Vertical stop pin
Special tape inside the rings keeps your scope tight without excessive clamp pressure!


In stock


Item Code: RGPM-25M4 [PY-A-793]

other products by Leapers > UTG

Create an online review and share your thoughts with other customers

5.0 5.0

5.0 5.0

By Patrick from USA on 2017-12-13
See all my reviews
Was this review helpful?
0.00 ratings

Things I liked: Great price....works as billed....when paired with the right scope it keep it low on the gun.

Things I would have changed: Nothing....

What others should know: I bought them for a 40mm objective lens scope that is max for medium rings.

 

5.0 5.0

5.0 5.0

By johnny from USA on 2017-03-12
See all my reviews
Was this review helpful?
5.01 rating

Things I liked: These are my go rings. I keep several pairs of the medium and high in stock for use when I get a new gun. They stay where they are supposed to.

Things I would have changed: nothing

What others should know: These aren't expensive so keep some of the medium and high for spares.

 

5.0 5.0

5.0 5.0

By Ron from USA on 2016-10-30
See all my reviews
Was this review helpful?
5.02 ratings

Things I liked: Very easy to set up and use.

Things I would have changed: Use counter sunk fasteners for a smoother less colthing catching setup

What others should know: Snug the fasteners only

 

Show Other ReviewsCreate an online review and share your thoughts with other customers

Got a question? Got an answer?
Log in, then enter your text.

  • Douglas from USA asked:

    Can I remove the stop pin? My dovetail doesn't have a hole for it.

    • Chevota from USA:

      Yes, it just screws out either up or down and out. I'd save it just in case.

  • Timothy from USA asked:

    Will these rings fit a Hatsan Edge, and Centerpoint 4-16x40mmAO scope?

    • Chevota from USA:

      I don't have that same gun but that dimension is basically the same as mine. I've used them on 40mmAO and 44mm w/o AO and they're a similar fit, which is close but it works. With the UTG scope SCP3-UM312AOIEW (44mm) on a generic Crosman B18 break barrel there was ~.024" clearance between the rubber lens cover and the gun. W/o the cover there was ~.120". So yes it'll fit but it also depends on how much shim the scope will need. I've found that on avg it means you can't get the scope cap on unless you trim it, which is easy for hard plastic caps, not so easy for rubber ones like the UTG has. I'd much rather have no cap than use the High mounts b/c I hate the scope on stilts look. You don't have to shim the scope, it just works better shimmed. Or just shim it as far as it'll go with the cap on.

    • John from USA:

      These medium rings should fit a 40mm scope. Any bigger than 40mm and it's best to use high rings.

  • chuck from USA asked:

    Will these fit a gamo air rifle?

    • Chevota from USA:

      As long as it has dovetail rails, which most do.

See all discussions

Consider the following similar item(s)

You may also like

Navigation