UTG Universal Dovetail To Picatinny/Weaver Adapter

This product works very good and is quite unique, This is something I will be ordering again soon because I have more projects coming up that will require this for a very secure platform to build from..THANKS.. P.S first time I used this product and I really like it..THANKS AGAIN..

Nothing...

When installed properly you would need a large hammer to get this mount to move it is that good...THANKS..P.S sure wish this would have been available years ago...

I used it on one of my Walther UIT BV's that has a very short rear mounting area. The front overhang worked great though I wish it was 30 to 50mm longer.

Longer front area for my particular use.

BE AWARE.... Use some anti seize on the screw threads and under the threads. Also pre-squeeze the mount to your 11mm dovetails. Meaning, pre-bend the mount side walls before you apply it to your receiver. If you over bend them, the mount has provisions to widen it again. You will likely use the spreader screws to remove the mount from your gun so that you don't scuff the bluing.

Beautifully made. Fits perfectly and, I think, absolutely necessary on most break barrels to get a comfortable "cheek weld" when shooting. Without this Adapter, I have to put my head forward to see clearly through the rifle scope and then it is hard to get a comfortable "cheek weld". This Adapter mounts very securely and does not move when mounted on my high FPE Hatsans. My rifles need little adjustment over time and use.

None.

Keep your instructions in case you want to remove the Adapter. There is a special technique to remove the Adapter!

Solid mount,amazing machining

Others mentioned that it does not work on an airforce texan.It does but you have to put the bolts extremely tight.

I really like the generous room for the offset, with a lot of smaller or shorter scopes it's very necessary for proper I relieve. The rail comes very tight and with spreader bolts much like be much like BKL The rail comes very tight and with spreader bolts much like be much like BKL and the quality is very comparable aswell. The stopping pin is a nice bonus although it didn't work for the proper offset I need on my Crossman. Not a game changer I think I'll be fine without using that. The instructions were very easy to read and follow and it came with torque specs.

It's great the way it is but maybe spec it to strictly picatinny.

The instructions are kind of tricky to find in the packaging. They're in between the outer and inner cardboard.

Nothing.

Make it a two-piece base so it will actually hold onto a dovetail rail.

Completely useless. The base of this is a single piece, so there is actually no way to tighten it to the rail. I tried putting it on an Airforce Texan to use Picatinny rings to mount the scope, and it just would not grip the rail. By the instructions, they want you to run the long screws all the way through and use them to, I don't know, bend the solid, one-piece aluminum base to squeeze the dovetail? The thing just doesn't work.

Solid mount with a very nice set-up.

Mounted this on my Nitro Piston Rifle and it's doing great. No shifts in point of aim after several hundred shots. Solid mount with plenty of clearance for large diameter scopes.

I like the adjust ability of the adapter you can easily adjust the scope forward or backward for eye relief.

Nothing.

This UTG Universal Dovetail to Picatinny / Weaver Adapter works grate on my Umarex Octane.

works good

This UTG picatinny mount does exactly what it is intended to do, at least when mounted in a standard 11mm grooved receiver, and at least when mounted in the crisply executed and finely machined grooves of quality receivers. Out of the package the mount is just a bit wider than the 11mm grooves, so in my experience there was no need to widen the mount further. The directions that are included are very clear, both as to text and photographic illustrations. Follow them precisely and deliberately, and the mounting should succeed perfectly. Tighten the four long machine screws slowly, deliberately and sequentially, rotating between them to maintain an even tightening along the length of the mount. I found this mount to be precisely engineered and handsomely finished. It mounted very solidly, and did exactly what it claimed to do. I was entirely satisfied with the result.

Nothing.

As for the claim of its being a "universal" mount, I cannot speak to that. However, I am not certain than I would wish to mount this on a 3/8 inch receiver, as I might be a bit concerned that tightening it down to 9.9mm might over-stress the aluminum, even if executed slowly and carefully, as a number of reviewers have complained. Also, be aware that not all grooved receivers may be machined as crisply, deeply, exactly and uniformly as others. The UTG is a precision product designed for a precise application.